Abstract: In this paper, applying He-s energy balance method to determine frequency formulation relations of nonlinear oscillators with discontinuous term or fractional potential. By calculation and computer simulations, compared with the exact solutions show that the results obtained are of high accuracy.
Abstract: This work investigated the steady state and dynamic
simulation of a fixed bed industrial naphtha reforming reactors. The
performance of the reactor was investigated using a heterogeneous
model. For process simulation, the differential equations are solved
using the 4th order Runge-Kutta method .The models were validated
against measured process data of an existing naphtha reforming plant.
The results of simulation in terms of components yields and
temperature of the outlet were in good agreement with empirical data.
The simple model displays a useful tool for dynamic simulation,
optimization and control of naphtha reforming.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: The approach based on the wavelet transform has
been widely used for image denoising due to its multi-resolution
nature, its ability to produce high levels of noise reduction and the
low level of distortion introduced. However, by removing noise, high
frequency components belonging to edges are also removed, which
leads to blurring the signal features. This paper proposes a new
method of image noise reduction based on local variance and edge
analysis. The analysis is performed by dividing an image into 32 x 32
pixel blocks, and transforming the data into wavelet domain. Fast
lifting wavelet spatial-frequency decomposition and reconstruction is
developed with the advantages of being computationally efficient and
boundary effects minimized. The adaptive thresholding by local
variance estimation and edge strength measurement can effectively
reduce image noise while preserve the features of the original image
corresponding to the boundaries of the objects. Experimental results
demonstrate that the method performs well for images contaminated
by natural and artificial noise, and is suitable to be adapted for
different class of images and type of noises. The proposed algorithm
provides a potential solution with parallel computation for real time
or embedded system application.
Abstract: The existence of many biological systems,
especially human societies, is based on cooperative behavior
[1, 2]. If natural selection favors selfish individuals, then what
mechanism is at work that we see so many cooperative
behaviors? One answer is the effect of network structure. On a
graph, cooperators can evolve by forming network bunches
[2, 3, 4]. In a research, Ohtsuki et al used the idea of iterated
prisoners- dilemma on a graph to model an evolutionary
game. They showed that the average number of neighbors
plays an important role in determining whether cooperation is
the ESS of the system or not [3]. In this paper, we are going to
study the dynamics of evolution of cooperation in a social
network. We show that during evolution, the ratio of
cooperators among individuals with fewer neighbors to
cooperators among other individuals is greater than unity. The
extent to which the fitness function depends on the payoff of
the game determines this ratio.
Abstract: Frequency domain independent component analysis has
a scaling indeterminacy and a permutation problem. The scaling
indeterminacy can be solved by use of a decomposed spectrum. For
the permutation problem, we have proposed the rules in terms of gain
ratio and phase difference derived from the decomposed spectra and
the source-s coarse directions.
The present paper experimentally clarifies that the gain ratio and
the phase difference work effectively in a real environment but their
performance depends on frequency bands, a microphone-space and
a source-microphone distance. From these facts it is seen that it is
difficult to attain a perfect solution for the permutation problem in a
real environment only by either the gain ratio or the phase difference.
For the perfect solution, this paper gives a solution to the problems
in a real environment. The proposed method is simple, the amount of
calculation is small. And the method has high correction performance
without depending on the frequency bands and distances from source
signals to microphones. Furthermore, it can be applied under the real
environment. From several experiments in a real room, it clarifies
that the proposed method has been verified.
Abstract: Securing instream flows for aquatic ecosystems is
critical for sustainable water management and the promotion of
human and environmental health. Using a case study from the semiarid
region of southern Alberta (Canada) this paper considers how
the determination of instream flow standards requires judgments with
respect to: (1) The relationship between instream flow indicators and
assessments of overall environmental health; (2) The indicators used
to determine adequate instream flows, and; (3) The assumptions
underlying efforts to model instream flows given data constraints. It
argues that judgments in each of these areas have an inherently
ethical component because instream flows have direct effects on the
water(s) available to meet obligations to humans and non-humans.
The conclusion expands from the case study to generic issues
regarding instream flows, the growing water ethics literature and
prospects for linking science to policy.
Abstract: The present study was performed in Musa bay (northern part of the Persian Gulf) around the coastal area of Bandare-Imam Khomeini and Razi Petrochemical Companies. Sediment samples and effluent samples were collected from the selected stations, from June 2009 to June 2010. The samples were analyzed to determine the degree of hydrocarbon contamination. The average level of TPH concentration in the study area was more than the natural background value at all of the stations, especially at station BI1 which was the main effluent outlet of Bandar-e- Imam Khomeini petrochemical company. Also the concentration of total petroleum hydrocarbon was monitored in the effluents of aforementioned petrochemical companies and the results showed that the concentration of TPH in the effluents of Bandar-e- Imam Khomeini petrochemical company was greater than Razi petrochemical company which is may be related to the products of Bandar-e- Imam Khomeini petrochemical company (aromatics, polymers, chemicals, fuel).
Abstract: The optimal operation of proton exchange membrane fuel cell (PEMFC) requires good water management which is presented under two forms vapor and liquid. Moreover, fuel cells have to reach higher output require integration of some accessories which need electrical power. In order to analyze fuel cells operation and different species transport phenomena a biphasic mathematical model is presented by governing equations set. The numerical solution of these conservation equations is calculated by Matlab program. A multi-criteria optimization with weighting between two opposite objectives is used to determine the compromise solutions between maximum output and minimal stack size. The obtained results are in good agreement with available literature data.
Abstract: The paper aims to specify and build a system, a learning support in radiology-senology (breast radiology) dedicated to help assist junior radiologists-senologists in their radiologysenology- related activity based on experience of expert radiologistssenologists. This system is named SAFRS (i.e. system supporting the training of radiologists-senologists). It is based on the exploitation of radiologic-senologic images (primarily mammograms but also echographic images or MRI) and their related clinical files. The aim of such a system is to help breast cancer screening in education. In order to acquire this expert radiologist-senologist knowledge, we have used the CBR (case-based reasoning) approach. The SAFRS system will promote the evolution of teaching in radiology-senology by offering the “junior radiologist" trainees an advanced pedagogical product. It will permit a strengthening of knowledge together with a very elaborate presentation of results. At last, the know-how will derive from all these factors.
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: In this paper, an approach for finding optimized
layouts for connecting PV units delivering maximum array output
power is suggested. The approach is based on considering the
different varying parameters of PV units that might be extracted from
a general two-diode model. These are mainly, solar irradiation,
reverse saturation currents, ideality factors, series and shunt
resistances in addition to operating temperature. The approach has
been tested on 19 possible 2×3 configurations and allowed to
determine the optimized configurations as well as examine the effects
of the different units- parameters on the maximum output power.
Thus, using this approach, standard arrays with n×m units can be
configured for maximum generated power and allows designing PV
based systems having reduced surfaces to fit specific required power,
as it is the case for solar cars and other mobile systems.
Abstract: The Principal component regression (PCR) is a
combination of principal component analysis (PCA) and multiple linear regression (MLR). The objective of this paper is to revise the
use of PCR in shortwave near infrared (SWNIR) (750-1000nm) spectral analysis. The idea of PCR was explained mathematically and
implemented in the non-destructive assessment of the soluble solid
content (SSC) of pineapple based on SWNIR spectral data. PCR achieved satisfactory results in this application with root mean
squared error of calibration (RMSEC) of 0.7611 Brix°, coefficient of determination (R2) of 0.5865 and root mean squared error of crossvalidation
(RMSECV) of 0.8323 Brix° with principal components
(PCs) of 14.
Abstract: This paper examines the factors, which determine
R&D outsourcing behaviour at Japanese firms, from the viewpoints of
transaction cost and strategic management, since the latter half of the
1990s. This study uses empirical analysis, which involves the
application of large-sample data. The principal findings of this paper
are listed below. Firms that belong to a wider corporate group are more
active in executing R&D outsourcing activities. Diversification
strategies such as the expansion of product and sales markets have a
positive effect on the R&D outsourcing behaviour of firms. Moreover,
while quantitative R&D resources have positive influences on R&D
outsourcing, qualitative indices have no effect. These facts suggest
that R&D outsourcing behaviour of Japanese firms are consistent with
the two perspectives of transaction cost and strategic management.
Specifically, a conventional corporate group network plays an
important role in R&D outsourcing behaviour. Firms that execute
R&D outsourcing leverage 'old' networks to construct 'new' networks
and use both networks properly.
Abstract: Tailor-welded Blanks (TWBs) are tailor made for
different complex component designs by welding multiple metal
sheets with different thicknesses, shapes, coatings or strengths prior
to forming. In this study the Hemispherical Die Stretching (HDS) test
(out-of-plane stretching) of TWBs were simulated via
ABAQUS/Explicit to obtain the Forming Limit Diagrams (FLDs) of
Stainless steel (AISI 304) laser welded blanks with different
thicknesses. Two criteria were used to detect the start of necking to
determine the FLD for TWBs and parent sheet metals. These two
criteria are the second derivatives of the major and thickness strains
that are given from the strain history of simulation. In the other word,
in these criteria necking starts when the second derivative of
thickness or major strain reaches its maximum. With having the time
of onset necking, one can measure the major and minor strains at the
critical area and determine the forming limit curve.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: One of the most important issues in multi-criteria decision analysis (MCDA) is to determine the weights of criteria so that all alternatives can be compared based on the collective performance of criteria. In this paper, one of popular methods in data envelopment analysis (DEA) known as common weights (CWs) is used to determine the weights in MCDA. Two frontiers named ideal and anti-ideal frontiers, instead of ideal and anti-ideal alternatives, are defined based on two new proposed CWs models. Ideal and antiideal frontiers are more flexible than that of alternatives. According to the optimal solutions of these two models, the distances of an alternative from the ideal and anti-ideal frontiers are derived. Then, a relative distance is introduced to measure the value of each alternative. The suggested models are linear and despite weight restrictions are feasible. An example is presented for explaining the method and for comparing to the existing literature.
Abstract: For professions of high risk industries, simulation training has always been thought in terms of high degree of fidelity regarding the real operational situation. Due to the recent progress, this way of training is changing, modifying the human-computer and software interactions: the interactions between trainees during simulation training session tend to become virtual, transforming the social-based embodiness (the way subjects integrate social skills for interpersonal relationship with co-workers). On the basis of the analysis of eight different profession trainings, a categorization of interactions has help to produce an analytical tool, the social interactions table. This tool may be very valuable to point out the changes of social interactions when the training sessions are skipping from a high fidelity simulator to a virtual simulator. In this case, it helps the designers of professional training to analyze and to assess the consequences of the potential lack the social-based embodiness.
Abstract: This paper presents the use of the predictive fuzzy logic controller (PFLC) applied to attitude control system for agile micro-satellite. In order to reduce the effect of unpredictable time delays and large uncertainties, the algorithm employs predictive control to predict the attitude of the satellite. Comparison of the PFLC and conventional fuzzy logic controller (FLC) is presented to evaluate the performance of the control system during attitude maneuver. The two proposed models have been analyzed with the same level of noise and external disturbances. Simulation results demonstrated the feasibility and advantages of the PFLC on the attitude determination and control system (ADCS) of agile satellite.
Abstract: The evaluation of energy release rate and centre Crack
Opening Displacement (COD) for circumferential Through-Wall
Cracked (TWC) pipes is an important issue in the assessment of
critical crack length for unstable fracture. The ability to predict crack
growth continues to be an important component of research for
several structural materials. Crack growth predictions can aid the
understanding of the useful life of a structural component and the
determination of inspection intervals and criteria. In this context,
studies were carried out at CSIR-SERC on Nuclear Power Plant
(NPP) piping components subjected to monotonic as well as cyclic
loading to assess the damage for crack growth due to low-cycle
fatigue in circumferentially TWC pipes.