Abstract: A new strain of Type A influenza virus can cause the
transmission of H1N1 virus. This virus can spread between the
people by coughing and sneezing. Because the people are always
movement, so this virus can be easily spread. In this study, we
construct the dynamical network model of H1N1 virus by separating
the human into five groups; susceptible, exposed, infectious,
quarantine and recovered groups. The movement of people between
houses (local level) is considered. The behaviors of solutions to our
dynamical model are shown for the different parameters.
Abstract: Knee joint forces are available by in vivo measurement
using an instrumented knee prosthesis for small to moderate knee
flexion but not for high flexion yet. We created a 2D mathematical
model of the lower limb incorporating several new features such as a
patello-femoral mechanism, a thigh-calf contact at high knee flexion
and co-contracting muscles' force ratio, then used it to determine knee
joint forces arising from high knee flexions in four kneeling
conditions: rising with legs in parallel, with one foot forward, with or
without arm use. With arms used, the maximum values of knee joint
force decreased to about 60% of those with arms not used. When rising
with one foot forward, if arms are not used, the forward leg sustains a
force as large as that sustained when rising with legs parallel.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: As global industry developed rapidly, the energy
demand also rises simultaneously. In the production process, there’s a
lot of energy consumed in the process. Formally, the energy used in
generating the heat in the production process. In the total energy
consumption, 40% of the heat was used in process heat, mechanical
work, chemical energy and electricity. The remaining 50% were
released into the environment. It will cause energy waste and
environment pollution. There are many ways for recovering the waste
heat in factory. Organic Rankine Cycle (ORC) system can produce
electricity and reduce energy costs by recovering the waste of low
temperature heat in the factory. In addition, ORC is the technology
with the highest power generating efficiency in low-temperature heat
recycling. However, most of factories executives are still hesitated
because of the high implementation cost of the ORC system, even a lot
of heat are wasted. Therefore, this study constructs a nonlinear
mathematical model of waste heat recovery equipment configuration
to maximize profits. A particle swarm optimization algorithm is
developed to generate the optimal facility installation plan for the ORC
system.
Abstract: Testing accounts for the major percentage of technical
contribution in the software development process. Typically, it
consumes more than 50 percent of the total cost of developing a
piece of software. The selection of software tests is a very important
activity within this process to ensure the software reliability
requirements are met. Generally tests are run to achieve maximum
coverage of the software code and very little attention is given to the
achieved reliability of the software. Using an existing methodology,
this paper describes how to use Bayesian Belief Networks (BBNs) to
select unit tests based on their contribution to the reliability of the
module under consideration. In particular the work examines how the
approach can enhance test-first development by assessing the quality
of test suites resulting from this development methodology and
providing insight into additional tests that can significantly reduce
the achieved reliability. In this way the method can produce an
optimal selection of inputs and the order in which the tests are
executed to maximize the software reliability. To illustrate this
approach, a belief network is constructed for a modern software
system incorporating the expert opinion, expressed through
probabilities of the relative quality of the elements of the software,
and the potential effectiveness of the software tests. The steps
involved in constructing the Bayesian Network are explained as is a
method to allow for the test suite resulting from test-driven
development.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: This paper proposes a new approach to offer a private
cloud service in HPC clusters. In particular, our approach relies on
automatically scheduling users- customized environment request as a
normal job in batch system. After finishing virtualization request jobs,
those guest operating systems will dismiss so that compute nodes will
be released again for computing. We present initial work on the
innovative integration of HPC batch system and virtualization tools
that aims at coexistence such that they suffice for meeting the
minimizing interference required by a traditional HPC cluster. Given
the design of initial infrastructure, the proposed effort has the potential
to positively impact on synergy model. The results from the
experiment concluded that goal for provisioning customized cluster
environment indeed can be fulfilled by using virtual machines, and
efficiency can be improved with proper setup and arrangements.
Abstract: A glider is in essence an unpowered vehicle and in this project we designed and built an oceanic glider, designed to operate underwater. This Glider was designed to collect ocean data such as temperature, pressure and (in future measures physical dimensions of the operating environment) and output this data to an external source. Development of the Oceanic Glider required research into various actuation systems that control buoyancy, pitch and yaw and the dynamics of these systems. It also involved the design and manufacture of the Glider and the design and implementation of a controller that enabled the Glider to navigate and move in an appropriate manner.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is of fundamental importance because it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, in developed countries, exclusive breastfeeding has decreased the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we study the factors that influence exclusive breastfeeding and use the Generalized Poisson regression model to analyze the practices of exclusive breastfeeding in Mauritius. We develop two sets of quasi-likelihood equations (QLE)to estimate the parameters.
Abstract: Cameron Highlands is a mountainous area subjected
to torrential tropical showers. It extracts 5.8 million liters of water
per day for drinking supply from its rivers at several intake points.
The water quality of rivers in Cameron Highlands, however, has
deteriorated significantly due to land clearing for agriculture,
excessive usage of pesticides and fertilizers as well as construction
activities in rapidly developing urban areas. On the other hand, these
pollution sources known as non-point pollution sources are diverse
and hard to identify and therefore they are difficult to estimate.
Hence, Geographical Information Systems (GIS) was used to provide
an extensive approach to evaluate landuse and other mapping
characteristics to explain the spatial distribution of non-point sources
of contamination in Cameron Highlands. The method to assess
pollution sources has been developed by using Cameron Highlands
Master Plan (2006-2010) for integrating GIS, databases, as well as
pollution loads in the area of study. The results show highest annual
runoff is created by forest, 3.56 × 108 m3/yr followed by urban
development, 1.46 × 108 m3/yr. Furthermore, urban development
causes highest BOD load (1.31 × 106 kgBOD/yr) while agricultural
activities and forest contribute the highest annual loads for
phosphorus (6.91 × 104 kgP/yr) and nitrogen (2.50 × 105 kgN/yr),
respectively. Therefore, best management practices (BMPs) are
suggested to be applied to reduce pollution level in the area.
Abstract: This article presents the simulation, parameterization and optimization of an electromagnet with the C–shaped configuration, intended for the study of magnetic properties of materials. The electromagnet studied consists of a C-shaped yoke, which provides self–shielding for minimizing losses of magnetic flux density, two poles of high magnetic permeability and power coils wound on the poles. The main physical variable studied was the static magnetic flux density in a column within the gap between the poles, with 4cm2 of square cross section and a length of 5cm, seeking a suitable set of parameters that allow us to achieve a uniform magnetic flux density of 1x104 Gaussor values above this in the column, when the system operates at room temperature and with a current consumption not exceeding 5A. By means of a magnetostatic analysis by the finite element method, the magnetic flux density and the distribution of the magnetic field lines were visualized and quantified. From the results obtained by simulating an initial configuration of electromagnet, a structural optimization of the geometry of the adjustable caps for the ends of the poles was performed. The magnetic permeability effect of the soft magnetic materials used in the poles system, such as low– carbon steel (0.08% C), Permalloy (45% Ni, 54.7% Fe) and Mumetal (21.2% Fe, 78.5% Ni), was also evaluated. The intensity and uniformity of the magnetic field in the gap showed a high dependence with the factors described above. The magnetic field achieved in the column was uniform and its magnitude ranged between 1.5x104 Gauss and 1.9x104 Gauss according to the material of the pole used, with the possibility of increasing the magnetic field by choosing a suitable geometry of the cap, introducing a cooling system for the coils and adjusting the spacing between the poles. This makes the device a versatile and scalable tool to generate the magnetic field necessary to perform magnetic characterization of materials by techniques such as vibrating sample magnetometry (VSM), Hall-effect, Kerr-effect magnetometry, among others. Additionally, a CAD design of the modules of the electromagnet is presented in order to facilitate the construction and scaling of the physical device.
Abstract: The increasing importance of data stream arising in a
wide range of advanced applications has led to the extensive study of
mining frequent patterns. Mining data streams poses many new
challenges amongst which are the one-scan nature, the unbounded
memory requirement and the high arrival rate of data streams. In this
paper, we propose a new approach for mining itemsets on data
stream. Our approach SFIDS has been developed based on FIDS
algorithm. The main attempts were to keep some advantages of the
previous approach and resolve some of its drawbacks, and
consequently to improve run time and memory consumption. Our
approach has the following advantages: using a data structure similar
to lattice for keeping frequent itemsets, separating regions from each
other with deleting common nodes that results in a decrease in search
space, memory consumption and run time; and Finally, considering
CPU constraint, with increasing arrival rate of data that result in
overloading system, SFIDS automatically detect this situation and
discard some of unprocessing data. We guarantee that error of results
is bounded to user pre-specified threshold, based on a probability
technique. Final results show that SFIDS algorithm could attain
about 50% run time improvement than FIDS approach.
Abstract: Performance of a cobalt doped sol-gel derived silica (Co/SiO2) catalyst for Fischer–Tropsch synthesis (FTS) in slurryphase reactor was studied using paraffin wax as initial liquid media. The reactive mixed gas, hydrogen (H2) and carbon monoxide (CO) in a molar ratio of 2:1, was flowed at 50 ml/min. Braunauer-Emmett- Teller (BET) surface area and X-ray diffraction (XRD) techniques were employed to characterize both the specific surface area and crystallinity of the catalyst, respectively. The reduction behavior of Co/SiO2 catalyst was investigated using the Temperature Programmmed Reduction (TPR) method. Operating temperatures were varied from 493 to 533K to find the optimum conditions to maximize liquid fuels production, gasoline and diesel.
Abstract: Smart Dust particles, are small smart materials used for generating weather maps. We investigate question of the optimal number of Smart Dust particles necessary for generating precise, computationally feasible and cost effective 3–D weather maps. We also give an optimal matching algorithm for the generalized scenario, when there are N Smart Dust particles and M ground receivers.
Abstract: In view of their importance and usefulness in reliability theory and probability distributions, several generalizations of the inverse Gaussian distribution and the Krtzel function are investigated in recent years. This has motivated the authors to introduce and study a new generalization of the inverse Gaussian distribution and the Krtzel function associated with a product of a Bessel function of the third kind )(zKQ and a Z - Fox-Wright generalized hyper geometric function introduced in this paper. The introduced function turns out to be a unified gamma-type function. Its incomplete forms are also discussed. Several properties of this gamma-type function are obtained. By means of this generalized function, we introduce a generalization of inverse Gaussian distribution, which is useful in reliability analysis, diffusion processes, and radio techniques etc. The inverse Gaussian distribution thus introduced also provides a generalization of the Krtzel function. Some basic statistical functions associated with this probability density function, such as moments, the Mellin transform, the moment generating function, the hazard rate function, and the mean residue life function are also obtained.KeywordsFox-Wright function, Inverse Gaussian distribution, Krtzel function & Bessel function of the third kind.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.