Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: In this paper, naturally immobilized lipase, Carica
papaya lipase, catalyzed biodiesel production from fish oil was
studied. The refined fish oil, extracted from the discarded parts of
fish, was used as a starting material for biodiesel production. The
effects of molar ratio of oil: methanol, lipase dosage, initial water
activity of lipase, temperature and solvent were investigated. It was
found that Carica papaya lipase was suitable for methanolysis of fish
oil to produce methyl ester. The maximum yield of methyl ester
could reach up to 83% with the optimal reaction conditions: oil:
methanol molar ratio of 1: 4, 20% (based on oil) of lipase, initial
water activity of lipase at 0.23 and 20% (based on oil) of tert-butanol
at 40oC after 18 h of reaction time. There was negligible loss in
lipase activity even after repeated use for 30 cycles.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: This paper suggests an algorithm for the evaluation
and selection of suppliers. At the beginning, all the needed materials and services used by the organization were identified and categorized
with regard to their nature by ABC method. Afterwards, in order to reduce risk factors and maximize the organization's profit, purchase strategies were determined. Then, appropriate criteria were identified for primary evaluation of suppliers applying to the organization. The output of this stage was a list of suppliers qualified by the organization to participate in its tenders. Subsequently, considering a material in particular, appropriate criteria on the ordering of the
mentioned material were determined, taking into account the particular materials' specifications as well as the organization's needs. Finally, for the purpose of validation and verification of the
proposed model, it was applied to Mobarakeh Steel Company (MSC), the qualified suppliers of this Company are ranked by the means of a Hierarchical Fuzzy TOPSIS method. The obtained results
show that the proposed algorithm is quite effective, efficient and easy to apply.
Abstract: Photoselective plastic films with thermic properties
are now available so that greenhouses clad with such plastics exhibit
a higher degree of “Greenhouse Effect” with a consequent increase in
night time temperature. In this study, we investigate the potential
benefits of a range of thermic plastic films used as greenhouse cover
materials on the vegetative and reproductive growth and development
of Iceberg lettuce (Lactuca sativa L). Transplants were grown under
thermic films and destructively harvested 4, 5, and 6 weeks after
transplanting. Thermic films can increase night temperatures up to 2
⁰C reducing the wide fluctuation in greenhouse temperature during
winter compared to the standard commercial film and consequently
increased the yield (leaf number, fresh weight, and dry weight) of
lettuce plants. Lettuce plants grown under Clear film respond to cold
stress by the accumulation of secondary products (phenolics, and
flavonoids).
Abstract: To determine the length of engagement threads of a bolt installed in a tapped part in order to avoid the threads stripping remains a very current problem in the design of the thread assemblies. It does not exist a calculation method formalized for the cases where the bolt is screwed directly in a ductile material. In this article, we study the behavior of the threads stripping of a loaded assembly by using a modelling by finite elements and a rupture criterion by damage. This modelling enables us to study the different parameters likely to influence the behavior of this bolted connection. We study in particular, the influence of couple of materials constituting the connection, of the bolt-s diameter and the geometrical characteristics of the tapped part, like the external diameter and the length of engagement threads. We established an experiments design to know the most significant parameters. That enables us to propose a simple expression making possible to calculate the resistance of the threads whatever the metallic materials of the bolt and the tapped part. We carried out stripping tests in order to validate our model. The estimated results are very close to those obtained by the tests.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: Laser beam forming is a novel technique developed for the joining of metallic components. In this study, an overview of the laser beam forming process, areas of application, the basic mechanisms of the laser beam forming process, some recent research
studies and the need to focus more research effort on improving the
laser-material interaction of laser beam forming of titanium and its
alloys are presented.
Abstract: In this study, Li4SiO4 powder was successfully
synthesized via sol gel method followed by drying at 150oC. Lithium
oxide, Li2O and silicon oxide, SiO2 were used as the starting
materials with citric acid as the chelating agent. The obtained powder
was then sintered at various temperatures. Crystallographic phase
analysis, morphology and ionic conductivity were investigated
systematically employing X-ray diffraction, Fourier Transform
Infrared, Scanning Electron Microscopy and AC impedance
spectroscopy. XRD result showed the formation of pure monoclinic
Li4SiO4 crystal structure with lattice parameters a = 5.140 Å, b =
6.094 Å, c = 5.293 Å, β = 90o in the sample sintered at 750oC. This
observation was confirmed by FTIR analysis. The bulk conductivity
of this sample at room temperature was 3.35 × 10-6 S cm-1 and the
highest bulk conductivity of 1.16 × 10-4 S cm-1 was obtained at
100°C. The results indicated that, the Li4SiO4 compound has
potential to be used as host for LISICON structured solid electrolyte
for low temperature application.
Abstract: Sound pathways in the enclosures of small earphones
are very narrow. In such narrow pathways, the speed of sound
propagation and the phase of sound waves change because of the air
viscosity. We have developed a new finite element method that
includes the effects of damping due to air viscosity for modeling the
sound pathway. This method is developed as an extension of the
existing finite element method for porous sound-absorbing materials.
The numerical calculation results using the proposed finite element
method are validated against the existing calculation methods.
Abstract: The possibility of radionuclides-related contamination
of lands at agricultural holdings defines the necessity to apply special
protective measures in plant growing. The aim of researches is to
elucidate the influence of polymers applying on biological migration
of man-made anthropogenic radionuclides 90Sr and 137Cs in the
system water - soil – plant. The tests are being carried out under field
conditions with and without application of polymers in root-inhabited
media in more radioecological tension zone (with the radius of 7 km
from the Armenian Nuclear Power Plant). The polymers on the base
of K+, Caµ, KµCaµ ions were tested. Productivity of pepper
depending on the presence and type of polymer material, content of
artificial radionuclides in waters, soil and plant material has been
determined. The character of different polymers influence on the
artificial radionuclides migration and accumulation in the system
water-soil-plant and accumulation in the plants has been cleared up.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: In recent years demolished concrete waste handling and management is the new primary challenging issue faced by the countries all over the world. It is very challenging and hectic problem that has to be tackled in an indigenous manner, it is desirable to completely recycle demolished concrete waste in order to protect natural resources and reduce environmental pollution. In this research paper an experimental study is carried out to investigate the feasibility and recycling of demolished waste concrete for new construction. The present investigation to be focused on recycling demolished waste materials in order to reduce construction cost and resolving housing problems faced by the low income communities of the world. The crushed demolished concrete wastes is segregated by sieving to obtain required sizes of aggregate, several tests were conducted to determine the aggregate properties before recycling it into new concrete. This research shows that the recycled aggregate that are obtained from site make good quality concrete. The compressive strength test results of partial replacement and full recycled aggregate concrete and are found to be higher than the compressive strength of normal concrete with new aggregate.
Abstract: Shape memory alloy (SMA) actuators have found a
wide range of applications due to their unique properties such as high
force, small size, lightweight and silent operation. This paper presents
the development of compact (SMA) actuator and cooling system in
one unit. This actuator is developed for multi-fingered hand. It
consists of nickel-titanium (Nitinol) SMA wires in compact forming.
The new arrangement insulates SMA wires from the human body by
housing it in a heat sink and uses a thermoelectric device for rejecting
heat to improve the actuator performance. The study uses
optimization methods for selecting the SMA wires geometrical
parameters and the material of a heat sink. The experimental work
implements the actuator prototype and measures its response.
Abstract: Applied a mouse-s roller with a gripper to increase the
efficiency for a gripper can learn to a material handling without
slipping. To apply a gripper, we use the optimize principle to develop
material handling by use a signal for checking a roller mouse that
rotate or not. In case of the roller rotates means that the material slips.
A gripper will slide to material handling until the roller will not
rotate. As this experiment has test material handling for comparing a
grip force that uses to material handling of the 10-human with the
applied gripper. We can summarize that human exert the material
handling more than the applied gripper. Because of the gripper can
exert more befit to material handling than human and may be a
minimum force to lift a material without slipping.
Abstract: The eco-efficient use of “waste" makes sense from
economic, social, and environmental perspectives. By efficiency diverting “waste" products back into useful and/or profitable inputs,
industries and entire societies can reap the benefits of improved financial profit, decreased environmental degradation, and overall
well-being of humanity.
In this project, several material flows at
Company Limited were investigated. Principles of "industrial ecology" were applied to improve the management of waste rubbers that are used in the jewelry manufacturing process. complete this project, a brief engineering analysis stream, and investigated eco-efficient principles for more efficient
handling of the materials and wastes were conducted, and the result were used to propose implementation strategies.
Abstract: Describes the current situation of educational Robotics
"the State of the art" its concept, its evolution their niches of
opportunity, academic and business and the importance of education
and academic outreach. It shows that the development of high-tech
automated educational materials influence the teaching-learning
process and that communication between machines and humans is a
reality.
Abstract: The impact of noise upon live quality has become an
important aspect to make both urban and environmental policythroughout
Europe and in Turkey. Concern over the quality of urban
environments, including noise levels and declining quality of green
space, is over the past decade with increasing emphasis on designing
livable and sustainable communities. According to the World Health
Organization, noise pollution is the third most hazardous
environmental type of pollution which proceeded by only air (gas
emission) and water pollution. The research carried out in two
phases, the first stage of the research noise and plant types providing
the suction of noise was evaluated through literature study and at the
second stage, definite types (Juniperus horizontalis L., Spirea
vanhouetti Briot., Cotoneaster dammerii C.K., Berberis thunbergii
D.C., Pyracantha coccinea M. etc.) were selected for the city of
Konya. Trials were conducted on the highway of Konya. The biggest
value of noise reduction was 6.3 dB(A), 4.9 dB(A), 6.2 dB(A) value
with compared to the control which includes the group that formed
by the bushes at the distance of 7m, 11m, 20m from the source and
5m, 9m, 20m of plant width, respectively. In this paper, definitions
regarding to noise and its sources were made and the precautions
were taken against to noise that mentioned earlier with the adverse
effects of noise. Plantation design approaches and suggestions
concerning to the diversity to be used, which are peculiar to roadside,
were developed to discuss the role and the function of plant material
to reduce the noise of the traffic.
Abstract: Electro Chemical Discharge Machining (ECDM) is an
emerging hybrid machining process used in precision machining of hard and brittle non-conducting materials. The present paper gives a
critical review on materials machined by ECDM under the prevailing machining conditions; capability indicators of the process are
reported. Some results obtained while performing experiments in micro-channeling on soda lime glass using ECDM are also presented. In these experiments, Tool Wear (TW) and Material Removal (MR)
were studied using design of experiments and L–4 orthogonal array. Experimental results showed that the applied voltage was the most influencing parameter in both MR and TW studies. Field
emission scanning electron microscopy (FESEM) results obtained on the microchannels confirmed the presence of micro-cracks, primarily responsible for MR. Chemical etching was also seen along the edges.
The Energy dispersive spectroscopy (EDS) results were used to detect the elements present in the debris and specimens.
Abstract: This was the first document revealing the
investigation of protein hydrolysate production optimization from J.
curcas cake. Proximate analysis of raw material showed 18.98%
protein, 5.31% ash, 8.52% moisture and 12.18% lipid. The
appropriate protein hydrolysate production process began with
grinding the J. curcas cake into small pieces. Then it was suspended
in 2.5% sodium hydroxide solution with ratio between solution/ J.
curcas cake at 80:1 (v/w). The hydrolysis reaction was controlled at
temperature 50 °C in water bath for 45 minutes. After that, the
supernatant (protein hydrolysate) was separated using centrifuge at
8000g for 30 minutes. The maximum yield of resulting protein
hydrolysate was 73.27 % with 7.34% moisture, 71.69% total protein,
7.12% lipid, 2.49% ash. The product was also capable of well
dissolving in water.