Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.
Abstract: One of the potential and effective ways of
storing thermal energy in buildings is the integration of brick with phase change materials (PCMs). This paper presents a two-dimensional model for simulating and analyzing of PCM
in order to minimize energy consumption in the buildings. The numerical approach has been used with the real weather data of a selected city of Iran (Tehran). Two kinds of brick integrated PCM are investigated and compared base on
outdoor weather conditions and the amount of energy
consumption. The results show a significant reduction in
maximum entering heat flux to building about 32.8%
depending on PCM quantity. The results are analyzed by
various temperature contour plots. The contour plots
illustrated the time dependent mechanism of entering heat flux for a brick integrated with PCM. Further analysis is developed to investigate the effect of PCM location on the inlet heat flux. The results demonstrated that to achieve maximum performance of PCM it is better to locate PCM near the outdoor.
Abstract: Introduction: Visual performance is an important factor in sport excellence. Visual involvement in a sport varies according to environmental demands associated with that sport. These environmental demands are matched by a task specific motor response. The purpose of this study was to determine if sport specific exercises will improve the visual performance of male rugby players, in order to achieve maximal results on the sports field. Materials & Methods: Twenty six adult male rugby players, aged 16-22, were chosen as subjects. In order to evaluate the effect of sport specific exercises on visual skills, a pre-test - post-test experimental group design was adopted for the study. Results: Significant differences (p≤0.05) were seen in the focussing, tracking, vergence, sequencing, eye-hand coordination and visualisation components Discussion & Conclusions: Sport specific exercises improved visual skills in rugby players which may provide them with an advantage over their opponents. This study suggests that these training programs and participation in regular on-line EyeDrills sports vision exercises (www.eyedrills.co.za) aimed at improving the athlete-s visual coordination, concentration, focus, hand-eye co-ordination, anticipation and motor response should be incorpotated in the rugby players exercise regime.
Abstract: A unique combination of adsorption and
electrochemical regeneration with a proprietary adsorbent material
called Nyex 100 was introduced at the University of Manchester for
waste water treatment applications. Nyex 100 is based on graphite
intercalation compound. It is non porous and electrically conducing
adsorbent material. This material exhibited very small BET surface
area i.e. 2.75 m2g-1, in consequence, small adsorptive capacities for
the adsorption of various organic pollutants were obtained. This work
aims to develop composite adsorbent material essentially capable of
electrochemical regeneration coupled with improved adsorption
characteristics. An organic dye, acid violet 17 was used as standard
organic pollutant. The developed composite material was
successfully electrochemically regenerated using a DC current of 1 A
for 60 minutes. Regeneration efficiency was maintained at around
100% for five adsorption-regeneration cycles.
Abstract: Canola is a specific edible type of rapeseed, developed
in the 1970s, which contains about 40 percent oil. This research was
carried out to determine the yield and some quality characteristics of
some winter canola cultivars during the 2010-2011 vegetation period
in Central Anatolia of Turkey. In this research; Oase, Dante,
Californium, Excalibur, Elvis, ES Hydromel, Licord, Orkan, Vectra,
Nelson, Champlain and NK Petrol winter canola varieties were used
as material. The field experiment was set up in a “Randomized
Complete Block Design” with three replications on 21 September
2010. In this research; seed yield, oil content, protein content, oil
yield and protein yield were examined.
As a result of this research; seed yield, oil content, oil yield and
protein yield (except protein content) were significant differences
between the cultivars. The highest seed yield (6348 kg ha-1) was
obtained from the NK Petrol, while the lowest seed yield (3949 kg
ha-1) was determined from the Champlain cultivar was obtained. The
highest oil content (46.73%) was observed from Oase and the lowest
value was obtained from Vectra (41.87%) cultivar. The highest oil
yield (2950 kg ha-1) was determined from NK Petrol while the least
value (1681 kg ha-1) was determined from Champlain cultivar. The
highest protein yield (1539.3 kg ha-1) was obtained from NK Petrol
and the lowest protein yield (976.5 kg ha-1) was obtained from
Champlain cultivar.
The main purpose of the cultivation of oil crops, to increase the
yield of oil per unit area. According the result of this research, NK
Petrol cultivar which ranks first with regard to both seed yield and oil
yield between cultivars as the most suitable winter canola cultivar of
local conditions.
Abstract: The dispersion of heavy particles line in an isotropic
and incompressible three-dimensional turbulent flow has been
studied using the Kinematic Simulation techniques to find out the
evolution of the line fractal dimension. In this study, the fractal
dimension of the line is found for different cases of heavy particles
inertia (different Stokes numbers) in the absence of the particle
gravity with a comparison with the fractal dimension obtained in the
diffusion case of material line at the same Reynolds number. It can
be concluded for the dispersion of heavy particles line in turbulent
flow that the particle inertia affect the fractal dimension of a line
released in a turbulent flow for Stokes numbers 0.02 < St < 2. At the
beginning for small times, most of the different cases are not affected
by the inertia until a certain time, the particle response time τa, with
larger time as the particles inertia increases, the fractal dimension of
the line increases owing to the particles becoming more sensitive to
the small scales which cause the change in the line shape during its
journey.
Abstract: Polyurethane foams (PUF) were formed by a chemical
reaction of polyol and isocyanate. The polyol was manufactured by
ring-opening hydrolysis of epoxidized soybean oil in the presence of
phosphoric acid under varying experimental conditions. Other
factors in the foam formulation such as water content and surfactant
were kept constant. The effect of the amount of solvents, phosphoric
acid, and their derivates in the foam formulation on the properties of
polyurethane foams were studied. The properties of the material were
measured via a number of parameters, which are water content of
prepared polyol, polymer density and cellular structures.
Abstract: This work presents a low-cost and eco-friendly
building material named Agrostone panel. Africa-s urban population
is growing at an annual rate of 2.8% and 62% of its population will
live in urban areas by 2050. As a consequence, many of the least
urbanized and least developed African countries- will face serious
challenges in providing affordable housing to the urban dwellers.
Since the cost of building materials accounts for the largest
proportion of the overall construction cost, innovating low-cost
building material is vital. Agrostone panel is used in housing projects
in Ethiopia. It uses raw materials of agricultural/industrial wastes
and/or natural minerals as a filler, magnesium-based chemicals as a
binder and fiberglass as reinforcement. Agrostone panel reduces the
cost of wall construction by 50% compared with the conventional
building materials. The pros and cons of Agrostone panel as well as
the use of other waste materials as a raw material to make the panel
more sustainable, low-cost and better properties are discussed.
Abstract: Austenite and Martensite indicate the phases of solids undergoing phase transformation which we usually associate with materials and not with living organisms. This article provides an overview of bacterial proteins and structures that are undergoing phase transformation and suggests its probable effect on mechanical behavior. The context is mainly within the role of phase transformations occurring in the flagellum of bacteria. The current knowledge of molecular mechanism leading to phase variation in living organisms is reviewed. Since in bacteria, each flagellum is driven by a separate motor, similarity to a Differential drive in case of four-wheeled vehicles is suggested. It also suggests the application of the mechanism in which bacteria changes its direction of movement to facilitate single point turning of a multi-wheeled vehicle. Finally, examples are presented to illustrate that the motion due to phase transformation of flagella in bacteria can start a whole new research on motion mechanisms.
Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper describes a new measuring algorithm for
three-dimensional (3-D) braided composite material .Braided angle is
an important parameter of braided composites. The objective of this
paper is to present an automatic measuring system. In the paper, the
algorithm is performed by using vcµ6.0 language on PC. An
advanced filtered algorithm for image of 3-D braided composites
material performs has been developed. The procedure is completely
automatic and relies on the gray scale information content of the
images and their local wavelet transform modulus maxims.
Experimental results show that the proposed method is feasible.
The algorithm was tested on both carbon-fiber and glass-fiber
performs.
Abstract: The ferroelectric behavior of barium strontium
titanate (BST) in thin film form has been investigated in order to
study the possibility of using BST for ferroelectric gate-field effect
transistor (FeFET) for memory devices application. BST thin films
have been fabricated as Al/BST/Pt/SiO2/Si-gate configuration. The
variation of the dielectric constant (ε) and tan δ with frequency have
been studied to ensure the dielectric quality of the material. The
results show that at low frequencies, ε increases as the Ba content
increases, whereas at high frequencies, it shows the opposite
variation, which is attributed to the dipole dynamics. tan δ shows low
values with a peak at the mid-frequency range. The ferroelectric
behavior of the Al/BST/Pt/SiO2/Si has been investigated using C-V
characteristics. The results show that the strength of the ferroelectric
hysteresis loop increases as the Ba content increases; this is attributed
to the grain size and dipole dynamics effect.
Abstract: Lignocellulosic materials are new targeted source to
produce second generation biofuels like biobutanol. However, this
process is significantly resisted by the native structure of biomass.
Therefore, pretreatment process is always essential to remove
hemicelluloses and lignin prior to the enzymatic hydrolysis.
The goals of pretreatment are removing hemicelluloses and
lignin, increasing biomass porosity, and increasing the enzyme
accessibility. The main goal of this research is to study the important
variables such as pretreatment temperature and time, which can give
the highest total sugar yield in pretreatment step by using dilute
phosphoric acid. After pretreatment, the highest total sugar yield of
13.61 g/L was obtained under an optimal condition at 140°C for 10
min of pretreatment time by using 1.75% (w/w) H3PO4 and at 15:1
liquid to solid ratio. The total sugar yield of two-stage process
(pretreatment+enzymatic hydrolysis) of 27.38 g/L was obtained.
Abstract: This paper deals with the thermo-mechanical deformation behavior of shear deformable functionally graded ceramicmetal (FGM) plates. Theoretical formulations are based on higher order shear deformation theory with a considerable amendment in the transverse displacement using finite element method (FEM). The mechanical properties of the plate are assumed to be temperaturedependent and graded in the thickness direction according to a powerlaw distribution in terms of the volume fractions of the constituents. The temperature field is supposed to be a uniform distribution over the plate surface (XY plane) and varied in the thickness direction only. The fundamental equations for the FGM plates are obtained using variational approach by considering traction free boundary conditions on the top and bottom faces of the plate. A C0 continuous isoparametric Lagrangian finite element with thirteen degrees of freedom per node have been employed to accomplish the results. Convergence and comparison studies have been performed to demonstrate the efficiency of the present model. The numerical results are obtained for different thickness ratios, aspect ratios, volume fraction index and temperature rise with different loading and boundary conditions. Numerical results for the FGM plates are provided in dimensionless tabular and graphical forms. The results proclaim that the temperature field and the gradient in the material properties have significant role on the thermo-mechanical deformation behavior of the FGM plates.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: Fly ash is one of the residues generated in
combustion, and comprises the fine particles that rise with the flue
gases. Ash which does not rise is termed bottom ash [1]. In our
country, it is expected that will be occurred 50 million tons of waste
ash per year until 2020. Released waste from the thermal power
plants is caused very significant problems as known. The fly ashes
can be evaluated by using as adsorbent material.
The purpose of this study is to investigate the possibility of use of
Tuncbilek fly ash like low-cost adsorbents for heavy metal
adsorption. First of all, Tuncbilek fly ash was characterized. For this
purpose; analysis such as sieve analysis, XRD, XRF, SEM and FT-IR
were performed.
Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: The purpose of this study is to introduce a new
interface program to calculate a dose distribution with Monte Carlo method in complex heterogeneous systems such as organs or tissues
in proton therapy. This interface program was developed under
MATLAB software and includes a friendly graphical user interface
with several tools such as image properties adjustment or results display. Quadtree decomposition technique was used as an image
segmentation algorithm to create optimum geometries from Computed Tomography (CT) images for dose calculations of proton
beam. The result of the mentioned technique is a number of nonoverlapped
squares with different sizes in every image. By this way
the resolution of image segmentation is high enough in and near
heterogeneous areas to preserve the precision of dose calculations
and is low enough in homogeneous areas to reduce the number of
cells directly. Furthermore a cell reduction algorithm can be used to combine neighboring cells with the same material. The validation of this method has been done in two ways; first, in comparison with experimental data obtained with 80 MeV proton beam in Cyclotron
and Radioisotope Center (CYRIC) in Tohoku University and second, in comparison with data based on polybinary tissue calibration method, performed in CYRIC. These results are presented in this paper. This program can read the output file of Monte Carlo code while region of interest is selected manually, and give a plot of dose distribution of proton beam superimposed onto the CT images.