Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: This paper addresses the problem of peak-to-average
power ratio (PAPR) in orthogonal frequency division multiplexing
(OFDM) systems. It also introduces a new PAPR reduction technique
based on adaptive square-rooting (SQRT) companding process. The
SQRT process of the proposed technique changes the statistical
characteristics of the OFDM output signals from Rayleigh
distribution to Gaussian-like distribution. This change in statistical
distribution results changes of both the peak and average power
values of OFDM signals, and consequently reduces significantly the
PAPR. For the 64QAM OFDM system using 512 subcarriers, up to 6
dB reduction in PAPR was achieved by square-rooting technique
with fixed degradation in bit error rate (BER) equal to 3 dB.
However, the PAPR is reduced at the expense of only -15 dB out-ofband
spectral shoulder re-growth below the in-band signal level. The
proposed adaptive SQRT technique is superior in terms of BER
performance than the original, non-adaptive, square-rooting
technique when the required reduction in PAPR is no more than 5
dB. Also, it provides fixed amount of PAPR reduction in which it is
not available in the original SQRT technique.
Abstract: The paper presents coupled electromagnetic and
thermal field analysis of busbar system (of rectangular cross-section
geometry) submitted to short circuit conditions. The laboratory model
was validated against both analytical solution and experimental
observations. The considered problem required the computation of
the detailed distribution of the power losses and the heat transfer
modes. In this electromagnetic and thermal analysis, different
definitions of electric busbar heating were considered and compared.
The busbar system is a three phase one and consists of aluminum,
painted aluminum and copper busbar. The solution to the coupled
field problem is obtained using the finite element method and the
QuickField™ program. Experiments have been carried out using two
different approaches and compared with computed results.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: The role of the pollen grain, with to the reproductive
process of higher plants, is to deliver the spermatic cells to the
embryo sac for egg fertilization. The aim of this project was study
the effect of electromagnetic fields on structure and pollen grains
development in Chenopodium album. Anthers of Chenopodium
album L. were collected at different stages of development from
control (without electromagnetic field) and plants grown at 10m from
the field sources. Structure and development of pollen grains were
studied and compared. The studying pollen structure by Light and
Scanning electron microscopy showed that electromagnetic fields
reduction of pollen grains number and male sterility, thus , in some
anthers, pollen grains were attached together and deformed compared
to control ones. The data presented suggest that prolonged exposures
of plants to magnetic field may cause different biological effects at
the cellular tissue and organ levels.
Abstract: In this paper, we present a novel objective nonreference
performance assessment algorithm for image fusion. It takes
into account local measurements to estimate how well the important
information in the source images is represented by the fused image.
The metric is based on the Universal Image Quality Index and uses
the similarity between blocks of pixels in the input images and the
fused image as the weighting factors for the metrics. Experimental
results confirm that the values of the proposed metrics correlate well
with the subjective quality of the fused images, giving a significant
improvement over standard measures based on mean squared error
and mutual information.
Abstract: Two-dimensional finite element model was created in this work to investigate the stresses distribution within rock-like samples with offset open non-persistent joints under biaxial loading. The results of this study have explained the fracture mechanisms observed in tests on rock-like material with open non-persistent offset joints [1]. Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-nodded isoperimetric plain strain element with two degree of freedom per node, and the three-nodded constant strain triangular element with two degree of freedom per node were used in the present study.The results of the present study explained the formation of wing cracks at the tip of the joints for low confining stress as well as the formation of wing cracks at the middle of the joint for the higher confining stress. High shear stresses found in the numerical study at the tip of the joints explained the formation of secondary cracks at the tip of the joints in the experimental study. The study results coincide with the experimental observations which showed that for bridge inclination of 0o, the coalescence occurred due to shear failure and for bridge inclination of 90o the coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occurred due to mixed tensile and shear failure.
Abstract: Sensors possess several properties of physical
measures. Whether devices that convert a sensed signal into an
electrical signal, chemical sensors and biosensors, thus all these
sensors can be considered as an interface between the physical and
electrical equipment. The problem is the analysis of the multitudes of
saved settings as input variables. However, they do not all have the
same level of influence on the outputs. In order to identify the most
sensitive parameters, those that can guide users in gathering
information on the ground and in the process of model calibration
and sensitivity analysis for the effect of each change made.
Mathematical models used for processing become very complex.
In this paper a fuzzy rule-based system is proposed as a solution
for this problem. The system collects the available signals
information from sensors. Moreover, the system allows the study of
the influence of the various factors that take part in the decision
system. Since its inception fuzzy set theory has been regarded as a
formalism suitable to deal with the imprecision intrinsic to many
problems. At the same time, fuzzy sets allow to use symbolic models.
In this study an example was applied for resolving variety of
physiological parameters that define human health state. The
application system was done for medical diagnosis help. The inputs
are the signals expressed the cardiovascular system parameters, blood
pressure, Respiratory system paramsystem was done, it will be able
to predict the state of patient according any input values.
Abstract: It is shown that the relationship of tick-borne
encephalitis virus with the human body comes in two ways, the
development of acute infection with the outcome in convalescence
and long stay by the virus in the body, its persistence in the nervous
tissue with periodic reactivation and prolonged circulating
immunoglobulin M. In spite of the fact that tick-borne encephalitis
virus has a tropism for nerve tissue, involvement in the process of
blood cells is an integral component of the infection. Comprehensive
study of the relation of factors of innate and adaptive immunity in the
tick-borne encephalitis providing insight into the features of chronic
disease.
Abstract: The blood ducts must be occluded to avoid loss of
blood from vessels in laparoscopic surgeries. This paper presents a
locking mechanism to be used in a ligation laparoscopic procedure
(LigLAP I), as an alternative solution for a stapling procedure.
Currently, stapling devices are being used to occlude vessels. Using
these devices may result in some problems, including injury of bile
duct, taking up a great deal of space behind the vessel, and bile leak.
In this new procedure, a two-layer suture occludes a vessel. A
locking mechanism is also required to hold the suture. Since there is
a limited space at the device tip, a Shape Memory Alloy (SMA)
actuator is used in this mechanism. Suitability for cleanroom
applications, small size, and silent performance are among the
advantages of SMA actuators in biomedical applications. An
experimental study is conducted to examine the function of the
locking mechanism. To set up the experiment, a prototype of a
locking mechanism is built using nitinol, which is a nickel-titanium
shape memory alloy. The locking mechanism successfully locks a
polymer suture for all runs of the experiment. In addition, the effects
of various surface materials on the applied pulling forces are studied.
Various materials are mounted at the mechanism tip to compare the
maximum pulling forces applied to the suture for each material. The
results show that the various surface materials on the device tip
provide large differences in the applied pulling forces.
Abstract: Silicon is a beneficial element for plant growth. It
helps plants to overcome multiple stresses, alleviates metal toxicity
and improves nutrient imbalance. Field experiment was conducted as
split-split plot arranged in a randomized complete block design with
four replications. Irrigation system include continues flooding and
deficit as main plots and nitrogen rates N0, N46, N92, and N138 kg/ha
as sub plots and silicon rates Si0 & Si500 kg/ha as sub-subplots.
Results indicate that grain yield had not significant difference
between irrigation systems. Flooding irrigation had higher biological
yield than deficit irrigation whereas, no significant difference in grain
and straw yield. Nitrogen application increased grain, biological and
straw yield. Silicon application increased grain, biological and straw
yield but, decreased harvest index. Flooding irrigation had higher
number of total tillers / hill than deficit irrigation, but deficit
irrigation had higher number of fertile tillers / hill than flooding
irrigation. Silicon increased number of filled spikelet and decreased
blank spikelet. With high nitrogen application decreased 1000-grain
weight. It can be concluded that if the nitrogen application was high
and water supplied was available we could have silicon application
until increase grain yield.
Abstract: This article presents a detailed analysis and comparative
performance evaluation of model reference adaptive control systems.
In contrast to classical control theory, adaptive control methods allow
to deal with time-variant processes. Inspired by the works [1] and
[2], two methods based on the MIT rule and Lyapunov rule are
applied to a linear first order system. The system is simulated and
it is investigated how changes to the adaptation gain affect the
system performance. Furthermore, variations in the reference model
parameters, that is changing the desired closed-loop behaviour are
examinded.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: In this paper, the typical exponential method, diamond difference and modified time discrete scheme is researched for self adaptive time step. The second-order time evolution scheme is applied to time-dependent spherical neutron transport equation by discrete ordinates method. The numerical results show that second-order time evolution scheme associated exponential method has some good properties. The time differential curve about neutron current is more smooth than that of exponential method and diamond difference and modified time discrete scheme.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: The great challenge of the agricultural sector is to
produce more crop from less water, which can be achieved by
increasing crop water productivity. The modernization of the
irrigation systems offers a number of possibilities to expand the
economic productivity of water and improve the virtual water status.
The objective of the present study is to assess the global water
productivity (GWP) within the major irrigation command areas of
I.R. Iran. For this purpose, fourteen irrigation command areas where
located in different areas of Iran were selected. In order to calculate
the global water productivity of irrigation command areas, all data on
the delivered water to cropping pattern, cultivated area, crops water
requirement, and yield production rate during 2002-2006 were
gathered. In each of the command areas it seems that the cultivated
crops have a higher amount of virtual water and thus can be replaced
by crops with less virtual water. This is merely suggested due to crop
water consumption and at the time of replacing crops, economic
value as well as cultural and political factors must be considered. The
results indicated that the lowest GWP belongs to Mahyar and
Borkhar irrigation areas, 0.24 kg m-3, and the highest is that of the
Dez irrigation area, 0.81 kg m-3. The findings demonstrated that
water management in the two irrigation areas is just efficient. The
difference in the GWP of irrigation areas is due to variations in the
cropping pattern, amount of crop productions, in addition to the
effective factors in the water use efficiency in the irrigation areas.