Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Most of the collision warning systems currently
available in the automotive market are mainly designed to warn
against imminent rear-end and lane-changing collisions. No collision
warning system is commercially available to warn against imminent
turning collisions at intersections, especially for left-turn collisions
when a driver attempts to make a left-turn at either a signalized or
non-signalized intersection, conflicting with the path of other
approaching vehicles traveling on the opposite-direction traffic
stream. One of the major factors that lead to left-turn collisions is the
human error and misjudgment of the driver of the turning vehicle
when perceiving the speed and acceleration of other vehicles
traveling on the opposite-direction traffic stream; therefore, using a
properly-designed collision warning system will likely reduce, or
even eliminate, this type of collisions by reducing human error. This
paper introduces perceptual framework for a proposed collision
warning system that can detect imminent left-turn collisions at
intersections. The system utilizes a commercially-available detection
sensor (either a radar sensor or a laser detector) to detect approaching
vehicles traveling on the opposite-direction traffic stream and
calculate their speeds and acceleration rates to estimate the time-tocollision
and compare that time to the time required for the turning
vehicle to clear the intersection. When calculating the time required
for the turning vehicle to clear the intersection, consideration is given
to the perception-reaction time of the driver of the turning vehicle,
which is the time required by the driver to perceive the message
given by the warning system and react to it by engaging the throttle.
A regression model was developed to estimate perception-reaction
time based on age and gender of the driver of the host vehicle.
Desired acceleration rate selected by the driver of the turning vehicle,
when making the left-turn movement, is another human factor that is
considered by the system. Another regression model was developed
to estimate the acceleration rate selected by the driver of the turning
vehicle based on driver-s age and gender as well as on the location
and speed of the nearest approaching vehicle along with the
maximum acceleration rate provided by the mechanical
characteristics of the turning vehicle. By comparing time-to-collision
with the time required for the turning vehicle to clear the intersection,
the system displays a message to the driver of the turning vehicle
when departure is safe. An application example is provided to
illustrate the logic algorithm of the proposed system.
Abstract: In this paper, we propose a method to reduce the
various kinds of noise while gathering and recording the
electrocardiogram (ECG) signal. Because of the defects of former
method in the noise elimination of ECG signal, we use translation
invariant (TI) multiwavelet denoising method to the noise elimination.
The advantage of the proposed method is that it may not only remain
the geometrical characteristics of the original ECG signal and keep the
amplitudes of various ECG waveforms efficiently, but also suppress
impulsive noise to some extent. The simulation results indicate that the
proposed method are better than former removing noise method in
aspects of remaining geometrical characteristics of ECG signal and the
signal-to-noise ratio (SNR).
Abstract: One of the important steps in a safety and risk management system is the economical evaluation of occupational accident and diseases costs in order to decrease accidents from reoccurring in the workplace. This study proposed a plausible method for calculating occupational accident costs and illnesses in work place. This method design for cost estimation takes into account both the personnel, organizational level as well as the community level especially intended for an Iranian work place. The research indicates that a using systematic method for calculating costs which also provides risk evaluation can help managers to plan correctly the investment in health and safety measures. Using this method is that not only is it comprehensive, easy and practical and could be applied in practice by a manager within a short period of time but it also shows the importance of accident costs as well as calculates the real cost of an accident and illnesses.
Abstract: The Resource-Constrained Project Scheduling
Problem (RCPSP) is concerned with single-item or small batch
production where limited resources have to be allocated to dependent
activities over time. Over the past few decades, a lot of work has
been made with the use of optimal solution procedures for this basic
problem type and its extensions. Brucker and Knust[1] discuss, how
timetabling problems can be modeled as a RCPSP. Authors discuss
high school timetabling and university course timetabling problem as
an example. We have formulated two mathematical formulations of
course timetabling problem in a new way which are the prototype of
single-mode RCPSP. Our focus is to show, how course timetabling
problem can be transformed into RCPSP. We solve this
transformation model with genetic algorithm.
Abstract: Three batches of yogurts were made with soy protein
isolate (SPI) supplemented with 2% (S2), 4% (S4) or 6% (S6) of
skim milk powder (SMP). The fourth batch (control; S0) was
prepared from SPI without SMP supplementation. Lactobacillus
delbrueckii ssp. bulgaricus ATCC 11842 (Lb 11842) and
Streptococcus thermophilus ST 1342 (ST 1342) were used as the
starter culture. Biotransformation of the inactive forms, isoflavone
glycosides (IG) to biologically active forms, isoflavone aglycones
(IA), was determined during 28 d storage. The viability of both
microorganisms was significantly higher (P < 0.05) in S2, S4, and S6
than that in S0. The ratio of lactic acid/acetic acid in S0 was in the
range of 15.53 – 22.31 compared to 7.24 – 12.81 in S2, S4 and S6.
The biotransformation of IG to IA in S2, S4 and S6 was also
enhanced by 9.9 -13.3% compared to S0.
Abstract: This article provides a comparative analysis of poetries of diverse nations around the world while largely focusing on Kazakh lyric poetry (Kazakh zhyraulyq oneri). Alongside, it sheds the light to the historical development and contemporary progress path of foremost poetry school located along the Syr Darya coast. Hereby, it-s content and central motives are examined.
Abstract: Categorical data based on description of the
agricultural landscape imposed some mathematical and analytical
limitations. This problem however can be overcome by data
transformation through coding scheme and the use of non-parametric
multivariate approach. The present study describes data
transformation from qualitative to numerical descriptors. In a
collection of 103 random soil samples over a 60 hectare field,
categorical data were obtained from the following variables: levels of
nitrogen, phosphorus, potassium, pH, hue, chroma, value and data on
topography, vegetation type, and the presence of rocks. Categorical
data were coded, and Spearman-s rho correlation was then calculated
using PAST software ver. 1.78 in which Principal Component
Analysis was based. Results revealed successful data transformation,
generating 1030 quantitative descriptors. Visualization based on the
new set of descriptors showed clear differences among sites, and
amount of variation was successfully measured. Possible applications
of data transformation are discussed.
Abstract: The aim of this study was to investigate ammonium
exchange capacity of natural and activated clinoptilolite from
Kwazulu-Natal Province, South Africa. X – ray fluorescence (XRF)
analysis showed that the clinoptilolite contained exchangeable ions
of sodium, potassium, calcium and magnesium. This analysis also
confirmed that the zeolite sample had a high silicon composition
compared to aluminium. Batch equilibrium studies were performed
in an orbital shaker and the data fitted the Langmuir isotherm very
well. The ammonium exchange capacity was found to increase with
pH and temperature. Clinoptilolite functionalization with
hydrochloric acid increased its ammonia uptake ability.
Abstract: Larval rearing and seed production of most of tetra fishes (Family: Characidae) is critical due to their small size larvae and limited numbers of spawning attempts. During the present study the effect of different live foods on growth and survival of neon tetra, Paracheirodon innesi larvae (length 3.1 ± 0.012mm, weight 0.048 ± 0.00015mg) and early fry (length = 6.44 ± 0.025mm, weight = 0.64 ± 0.003mg and 13 days old) was determined in two experiments. Experiment I was conducted for rearing the larvae by using mixed green water and Infusoria whereas, in Experiment II, early fry were fed with mixed zooplankton, decapsulated Artemia cyst and Artemia nauplii. The larvae fed on mixed green water showed significant (p
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Many metrics were proposed to evaluate the
characteristics of the analysis and design model of a given product
which in turn help to assess the quality of the product. Function point
metric is a measure of the 'functionality' delivery by the software.
This paper presents an analysis of a set of programs of a project
developed in Cµ through Function Points metric. Function points
are measured for a Data Flow Diagram (DFD) of the case developed
at initial stage. Lines of Codes (LOCs) and possible errors are
calculated with the help of measured Function Points (FPs). The
calculations are performed using suitable established functions.
Calculated LOCs and errors are compared with actual LOCs and
errors found at the time of analysis & design review, implementation
and testing. It has been observed that actual found errors are more
than calculated errors. On the basis of analysis and observations,
authors conclude that function point provides useful insight and helps
to analyze the drawbacks in the development process.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: Space-time block codes (STBC) and spatial multiplexing
(SM) are promising techniques that effectively exploit multipleinput
multiple-output (MIMO) transmission to achieve more reliable
communication and a higher multiplexing rate, respectively. In this
paper, we study a practical design for hybrid scheme with multi-input
multi-output orthogonal frequency division multiplexing (MIMOOFDM)
systems to flexibly maximize the tradeoff between diversity
and multiplexing gains. Unlike the existing STBC and SM designs
which are suitable for the integer multiplexing rate, the proposed
design can achieve arbitrary number of multiplexing rate.
Abstract: Supply chain consists of all stages involved, directly
or indirectly, includes all functions involved in fulfilling a customer
demand. In two stage transportation supply chain problem,
transportation costs are of a significant proportion of final product
costs. It is often crucial for successful decisions making approaches
in two stage supply chain to explicit account for non-linear
transportation costs. In this paper, deterministic demand and finite
supply of products was considered. The optimized distribution level
and the routing structure from the manufacturing plants to the
distribution centres and to the end customers is determined using
developed mathematical model and solved by proposed particle
swarm optimization based genetic algorithm. Numerical analysis of
the case study is carried out to validate the model.
Abstract: A real time image-guided electroplating system is
proposed in this paper. Unlike previous electroplating systems, instead
of using the intermittent mode to electroplate 500um long copper
specimen, a CCD camera and a motion controller are used to adjust
anode-cathode distance to obtain better results. Since the image of the
gap distance is highly deteriorated due to complex chemical-electrical
operation inside the electrolyte, to determine the gap distance, an
image processing algorithm is developed and mainly based on the
entropy and energy values. In addition, the color and incidence
direction of light source are also discussed to help the image process in
this paper. From the experiment results, the specimens created by the
proposed system show better structure, better uniformity and better
finishing surface compared to those by previous intermittent
electroplating setup.
Abstract: Pharmacology curriculum plays an integral role in
medical education. Learning pharmacology to choose and prescribe
drugs is a major challenge encountered by students. We developed
pharmacology applied learning activities for first year medical
students that included realistic clinical situations with escalating
complications which required the students to analyze the situation
and think critically to choose a safe drug. Tutor feedback was
provided at the end of session. Evaluation was done to assess the
students- level of interest and usefulness of the sessions in rational
selection of drugs. Majority (98 %) of the students agreed that the
session was an extremely useful learning exercise and agreed that
similar sessions would help in rational selection of drugs. Applied
learning sessions in the early years of medical program may promote
deep learning and bridge the gap between pharmacology theory and
clinical practice. Besides, it may also enhance safe prescribing skills.
Abstract: In intensity modulated radiation therapy (IMRT)
treatment planning, beam angles are usually preselected on the basis of
experience and intuition. Therefore, getting an appropriate beam
configuration needs a very long time. Based on the present situation,
the paper puts forward beam orientation optimization using ant colony
optimization (ACO). We use ant colony optimization to select the
beam configurations, after getting the beam configuration using
Conjugate Gradient (CG) algorithm to optimize the intensity profiles.
Combining with the information of the effect of pencil beam, we can
get the global optimal solution accelerating. In order to verify the
feasibility of the presented method, a simulated and clinical case was
tested, compared with dose-volume histogram and isodose line
between target area and organ at risk. The results showed that the
effect was improved after optimizing beam configurations. The
optimization approach could make treatment planning meet clinical
requirements more efficiently, so it had extensive application
perspective.