Abstract: If an unsteady heat transfer or heat impulse happens in
part of the cryogenic pipeline system of large space environment
simulation equipment while running in vacuum environment, it will
lead to abnormal flow of the cryogenic fluid in the pipeline. When the
situation gets worse, the cryogenic fluid in the pipeline will have phase
change and a gas block which results in the malfunction of the
cryogenic pipeline system. Referring to the structural parameter of a
typical cryogenic pipeline system and the basic equation, an analytical
model and a calculation model for cryogenic pipeline system can be
built. The various factors which influence the thermal resistance of a
cryogenic pipeline system can be analyzed and calculated by using the
qualitative analysis relation deduced for thermal resistance of pipeline.
The research conclusion could provide theoretical support for the
design and operation of a cryogenic pipeline system
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: Business and IT alignment has continued as a
top concern for business and IT executives for almost three
decades. Many researchers have conducted empirical studies on
the relationship between business-IT alignment and performance.
Yet, these approaches, lacking a social perspective, have had little
impact on sustaining performance and competitive advantage. In
addition to the limited alignment literature that explores
organisational learning that is represented in shared understanding,
communication, cognitive maps and experiences.
Hence, this paper proposes an integrated process that enables
social and intellectual dimensions through the concept of
organisational learning. In particular, the feedback and feedforward
process which provide a value creation across dynamic
multilevel of learning. This mechanism enables on-going
effectiveness through development of individuals, groups and
organisations, which improves the quality of business and IT
strategies and drives to performance.
Abstract: Due to insufficient frequency band and tremendous growth of the mobile users, complex computation is needed for the use of resources. Long distance communication began with the introduction of telegraphs and simple coded pulses, which were used to transmit short messages. Since then numerous advances have rendered reliable transfer of information both easier and quicker. Wireless network refers to any type of computer network that is wireless, and is commonly associated with a telecommunications network whose interconnections between nodes is implemented without the use of wires. Wireless network can be broadly categorized in infrastructure network and infrastructure less network. Infrastructure network is one in which we have a base station to serve the mobile users and in the infrastructure less network is one in which no infrastructure is available to serve the mobile users this kind of networks are also known as mobile Adhoc networks. In this paper we have simulated the result for different scenarios with protocols like AODV and DSR; we simulated the result for throughput, delay and receiving traffic in the given scenario.
Abstract: This paper presents a dynamic model for mechanical
loads of an electric drive, including angular misalignment and
including load unbalance. The misalignment model represents the
effects of the universal joint between the motor and the mechanical
load. Simulation results are presented for an induction motor driving
a mechanical load with angular misalignment for both flexible and
rigid coupling. The models presented are very useful in the study of
mechanical fault detection in induction motors, using mechanical and
electrical signals already available in a drive system, such as speed,
torque and stator currents.
Abstract: This research aims at development of the Multiple
Intelligences Measurement of Elementary Students. The structural
accuracy test and normality establishment are based on the Multiple
Intelligences Theory of Gardner. This theory consists of eight aspects
namely linguistics, logic and mathematics, visual-spatial relations,
body and movement, music, human relations, self-realization/selfunderstanding
and nature. The sample used in this research consists
of elementary school students (aged between 5-11 years). The size of
the sample group was determined by Yamane Table. The group has
2,504 students. Multistage Sampling was used. Basic statistical
analysis and construct validity testing were done using confirmatory
factor analysis. The research can be summarized as follows; 1.
Multiple Intelligences Measurement consisting of 120 items is
content-accurate. Internal consistent reliability according to the
method of Kuder-Richardson of the whole Multiple Intelligences
Measurement equals .91. The difficulty of the measurement test is
between .39-.83. Discrimination is between .21-.85. 2). The Multiple
Intelligences Measurement has construct validity in a good range,
that is 8 components and all 120 test items have statistical
significance level at .01. Chi-square value equals 4357.7; p=.00 at the
degree of freedom of 244 and Goodness of Fit Index equals 1.00.
Adjusted Goodness of Fit Index equals .92. Comparative Fit Index
(CFI) equals .68. Root Mean Squared Residual (RMR) equals 0.064
and Root Mean Square Error of Approximation equals 0.82. 3). The
normality of the Multiple Intelligences Measurement is categorized
into 3 levels. Those with high intelligence are those with percentiles
of more than 78. Those with moderate/medium intelligence are those
with percentiles between 24 and 77.9. Those with low intelligence
are those with percentiles from 23.9 downwards.
Abstract: An original Direct Numerical Simulation (DNS) method to tackle the problem of particulate flows at moderate to high concentration and finite Reynolds number is presented. Our method is built on the framework established by Glowinski and his coworkers [1] in the sense that we use their Distributed Lagrange Multiplier/Fictitious Domain (DLM/FD) formulation and their operator-splitting idea but differs in the treatment of particle collisions. The novelty of our contribution relies on replacing the simple artificial repulsive force based collision model usually employed in the literature by an efficient Discrete Element Method (DEM) granular solver. The use of our DEM solver enables us to consider particles of arbitrary shape (at least convex) and to account for actual contacts, in the sense that particles actually touch each other, in contrast with the simple repulsive force based collision model. We recently upgraded our serial code, GRIFF 1 [2], to full MPI capabilities. Our new code, PeliGRIFF 2, is developed under the framework of the full MPI open source platform PELICANS [3]. The new MPI capabilities of PeliGRIFF open new perspectives in the study of particulate flows and significantly increase the number of particles that can be considered in a full DNS approach: O(100000) in 2D and O(10000) in 3D. Results on the 2D/3D sedimentation/fluidization of isometric polygonal/polyedral particles with collisions are presented.
Abstract: The development of One Tambon One Product
(OTOP) became the policy of the government in 1997 after the
former Prime Minister had been in power. The strategy of sections is
currently set for the policy. OTOP has become the part of the way of
community lives around the country. OTOP may be developed under
changing into ASEAN economic community in 2015 because of the
flow of capitals, productions, and many workers in the region. All
sectors are improved for the change. The purposes of study were to
study the strength and weakness of the OTOP-creating process via its
policy and to lead to the strategy to be able to apply before changing.
The methodology is qualitative to study its policy including
document and to interview experienced persons. The findings showed
that the effort of improvement of all sectors obviously involves with
OTOP development. Particularly, the strategic administration of
OTOP is in every level of the state, central sector, region, and
community.
Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: The Influence Diagrams (IDs) is a kind of Probabilistic Belief Networks for graphic modeling. The usage of IDs can improve the communication among field experts, modelers, and decision makers, by showing the issue frame discussed from a high-level point of view. This paper enhances the Time-Sliced Influence Diagrams (TSIDs, or called Dynamic IDs) based formalism from a Discrete Event Systems Modeling and Simulation (DES M&S) perspective, for Exploring Analysis (EA) modeling. The enhancements enable a modeler to specify times occurred of endogenous events dynamically with stochastic sampling as model running and to describe the inter- influences among them with variable nodes in a dynamic situation that the existing TSIDs fails to capture. The new class of model is named Dynamic-Stochastic Influence Diagrams (DSIDs). The paper includes a description of the modeling formalism and the hiberarchy simulators implementing its simulation algorithm, and shows a case study to illustrate its enhancements.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: Corner detection and optical flow are common techniques for feature-based video stabilization. However, these algorithms are computationally expensive and should be performed at a reasonable rate. This paper presents an algorithm for discarding irrelevant feature points and maintaining them for future use so as to improve the computational cost. The algorithm starts by initializing a maintained set. The feature points in the maintained set are examined against its accuracy for modeling. Corner detection is required only when the feature points are insufficiently accurate for future modeling. Then, optical flows are computed from the maintained feature points toward the consecutive frame. After that, a motion model is estimated based on the simplified affine motion model and least square method, with outliers belonging to moving objects presented. Studentized residuals are used to eliminate such outliers. The model estimation and elimination processes repeat until no more outliers are identified. Finally, the entire algorithm repeats along the video sequence with the points remaining from the previous iteration used as the maintained set. As a practical application, an efficient video stabilization can be achieved by exploiting the computed motion models. Our study shows that the number of times corner detection needs to perform is greatly reduced, thus significantly improving the computational cost. Moreover, optical flow vectors are computed for only the maintained feature points, not for outliers, thus also reducing the computational cost. In addition, the feature points after reduction can sufficiently be used for background objects tracking as demonstrated in the simple video stabilizer based on our proposed algorithm.
Abstract: Wetting characteristics of reactive (Sn–0.7Cu solder)
and non– reactive (castor oil) wetting of liquids on Cu and Ag plated
Al substrates have been investigated. Solder spreading exhibited
capillary, gravity and viscous regimes. Oils did not exhibit noticeable
spreading regimes. Solder alloy showed better wettability on Ag
coated Al substrate compared to Cu plating. In the case of castor oil,
Cu coated Al substrate exhibited good wettability as compared to Ag
coated Al substrates. The difference in wettability during reactive
wetting of solder and non–reactive wetting of oils is attributed to the
change in the surface energies of Al substrates brought about by the
formation of intermetallic compounds (IMCs).
Abstract: This article proposes a voltage-mode
multifunction filter using differential voltage current
controllable current conveyor transconductance amplifier
(DV-CCCCTA). The features of the circuit are that: the
quality factor and pole frequency can be tuned independently
via the values of capacitors: the circuit description is very
simple, consisting of merely 1 DV-CCCCTA, and 2
capacitors. Without any component matching conditions, the
proposed circuit is very appropriate to further develop into
an integrated circuit. Additionally, each function response
can be selected by suitably selecting input signals with
digital method. The PSpice simulation results are depicted.
The given results agree well with the theoretical anticipation.
Abstract: This paper provides a key driver-based conceptual framework that can be used to improve a firm-s success in commercializing technology and in new product innovation resulting from collaboration with other organizations through strategic alliances. Based on a qualitative study using an interview approach, strategic alliances of entrepreneurs in the food processing industry in Thailand are explored. This paper describes factors affecting decisions to collaborate through alliances. It identifies four issues: maintaining the efficiency of the value chain for production capability, adapting to present and future competition, careful assessment of value of outcomes, and management of innovation. We consider five driving factors: resource orientation, assessment of risk, business opportunity, sharing of benefits and confidence in alliance partners. These factors will be of interest to entrepreneurs and policy makers with regard to further understanding of the direction of business strategies.
Abstract: The objectives of this research paper were to study the
influencing factors that contributed to the success of electronic
commerce (e-commerce) and to study the approach to enhance the
standard of e-commerce for small and medium enterprises (SME).
The research paper focused the study on only sole proprietorship
SMEs in Bangkok, Thailand. The factors contributed to the success
of SME included business management, learning in the organization,
business collaboration, and the quality of website. A quantitative and
qualitative mixed research methodology was used. In terms of
quantitative method, a questionnaire was used to collect data from
251 sole proprietorships. The System Equation Model (SEM) was
utilized as the tool for data analysis. In terms of qualitative method,
an in-depth interview, a dialogue with experts in the field of ecommerce
for SMEs, and content analysis were used.
By using the adjusted causal relationship structure model, it was
revealed that the factors affecting the success of e-commerce for
SMEs were found to be congruent with the empirical data. The
hypothesis testing indicated that business management influenced the
learning in the organization, the learning in the organization
influenced business collaboration and the quality of the website, and
these factors, in turn, influenced the success of SMEs. Moreover, the
approach to enhance the standard of SMEs revealed that the majority
of respondents wanted to enhance the standard of SMEs to a high
level in the category of safety of e-commerce system, basic structure
of e-commerce, development of staff potentials, assistance of budget
and tax reduction, and law improvement regarding the e-commerce
respectively.
Abstract: This paper presents a new STAKCERT KDD
processes for worm detection. The enhancement introduced in the
data-preprocessing resulted in the formation of a new STAKCERT
model for worm detection. In this paper we explained in detail how
all the processes involved in the STAKCERT KDD processes are
applied within the STAKCERT model for worm detection. Based on
the experiment conducted, the STAKCERT model yielded a 98.13%
accuracy rate for worm detection by integrating the STAKCERT
KDD processes.
Abstract: The aim of this study is to show innovative techniques that describe the effectiveness of individuals diagnosed with antisocial personality disorders (ASPD). The author presents information about hate schemas regarding persons with ASPD and their understanding of the role of hate. The data of 60 prisoners with ASPD, 40 prisoners without ASPD, and 60 men without antisocial tendencies, has been analyzed. The participants were asked to describe their hate inspired by a photograph. The narrative discourse was analyzed, the three groups were compared. The results show the differences between the inmates with ASPD, those without ASPD, and the controls. The antisocial individuals describe hate as an ambivalent feeling with low emotional intensity, i.e., actors (in stories) are presented more as positives than as partners. They use different mechanisms to keep them from understanding the meaning of the emotional situation. The schema's characteristics were expressed in narratives attributed to high Psychopathy.
Abstract: The improvement of a filer case utilized to purify the
let-out smoke and smell in the production of Benjarong Ceramic is
studied through Participatory Action Research (PAR). This research
is aimed to protect smell, dirty smoke, and air pollution which are
effects of incomplete combustion in the production of Benjarong
ceramic. This research was conducted at Jongjint Benjarong Ceramic
Factory in Plai Bang, Bang Kruai, Nonthaburi Province,Thailand,
also 12 employees were interviewed for data collection. All collected
data were analyzed to develop and create solution to protect smoke
and smell pollution from Benjarong ceramic production.
The results revealed that the employees who have used the
developed filer cases are moderately satisfied. In addition to the
efficiency of developed smoke-and-smell filer cases, it was found
that Overall, the respondents were satisfied moderately with
efficiency of modified smoke and smell filter cases.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.