Abstract: During the last few years, several sheet hydroforming
processes have been introduced. Despite the advantages of these
methods, they have some limitations. Of the processes, the two main
ones are the standard hydroforming and hydromechanical deep
drawing. A new sheet hydroforming die set was proposed that has the
advantages of both processes and eliminates their limitations. In this
method, a polyurethane plate was used as a part of the die-set to
control the blank holder force. This paper outlines the Taguchi
optimization methodology, which is applied to optimize the effective
parameters in forming cylindrical cups by the new die set of sheet
hydroforming process. The process parameters evaluated in this
research are polyurethane hardness, polyurethane thickness, forming
pressure path and polyurethane hole diameter. The design of
experiments based upon L9 orthogonal arrays by Taguchi was used
and analysis of variance (ANOVA) was employed to analyze the
effect of these parameters on the forming pressure. The analysis of
the results showed that the optimal combination for low forming
pressure is harder polyurethane, bigger diameter of polyurethane hole
and thinner polyurethane. Finally, the confirmation test was derived
based on the optimal combination of parameters and it was shown
that the Taguchi method is suitable to examine the optimization
process.
Abstract: The ability to detect and classify the type of fault
plays a great role in the protection of power system. This procedure
is required to be precise with no time consumption. In this paper
detection of fault type has been implemented using wavelet analysis
together with wavelet entropy principle. The simulation of power
system is carried out using PSCAD/EMTDC. Different types of
faults were studied obtaining various current waveforms. These
current waveforms were decomposed using wavelet analysis into
different approximation and details. The wavelet entropy of such
decompositions is analyzed reaching a successful methodology for
fault classification. The suggested approach is tested using different
fault types and proven successful identification for the type of fault.
Abstract: Cast metal inlays can be used on molars requiring a
class II restoration instead amalgam and offer a durable alternative.
Because it is known that class II inlays may increase the
susceptibility to fracture, it is important to ensure optimal
performance in selection of the adequate preparation design to reduce
stresses in teeth structures and also in the restorations. The aim of the
study was to investigate the influence of preparation design on stress
distribution in molars with different class II preparations and in cast
metal inlays. The first step of the study was to achieve 3D models in
order to analyze teeth and cast metal class II inlays. The geometry of
the intact tooth was obtained by 3D scanning using a manufactured
device. With a NURBS modeling program the preparations and the
appropriately inlays were designed. 3D models of first upper molars
of the same shape and size were created. Inlay cavities designs were
created using literature data. The geometrical model was exported
and the mesh structure of the solid 3D model was created for
structural simulations. Stresses were located around the occlusal
contact areas. For the studied cases, the stress values were not
significant influenced by the taper of the preparation. it was
demonstrated stresses are higher in the cast metal restorations and
therefore the strength of the teeth is not affected.
Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: For best collaboration, Asynchronous tools and particularly the discussion forums are the most used thanks to their flexibility in terms of time. To convey only the messages that belong to a theme of interest of the tutor in order to help him during his tutoring work, use of a tool for classification of these messages is indispensable. For this we have proposed a semantics classification tool of messages of a discussion forum that is based on LSA (Latent Semantic Analysis), which includes a thesaurus to organize the vocabulary. Benefits offered by formal ontology can overcome the insufficiencies that a thesaurus generates during its use and encourage us then to use it in our semantic classifier. In this work we propose the use of some functionalities that a OWL ontology proposes. We then explain how functionalities like “ObjectProperty", "SubClassOf" and “Datatype" property make our classification more intelligent by way of integrating new terms. New terms found are generated based on the first terms introduced by tutor and semantic relations described by OWL formalism.
Abstract: There are various solutions for improving existing overhead line systems with the general purpose of increasing their limited capacity. The capacity reserve of the existing overhead lines is an important problem that must be considered from different aspects. The paper contains a comparative analysis of the mechanical and thermal limitations of an existing overhead line based on certain calculation conditions characterizing the examined variants. The methodology of the proposed estimation of the permissible conductor temperature and maximum load current is described in detail. The transmission line model consists of specific information of an existing overhead line of the Latvian power network. The main purpose of the simulation tasks is to find an additional capacity reserve by using accurate mathematical models. The results of the obtained data are presented.
Abstract: Nitrogen loss from irrigated cropland, particularly
sandy soils, significantly contributes to nitrate (NO3
-) levels in
surface and groundwaters. Thus, it is of great interest to use
inexpensive natural products that can increase the fertilizer efficiency
and decrease nitrate leaching. In this study, the ability of natural
Iranian zeolite clinoptilolite (Cp) and surfactant modified zeolite
clinoptilolite (SMZ) to remove NH4
+ and NO3
-, respectively, from
aqueous solutions was determined. The feasibility of using Cp and
SMZ as soil amendment to reduce nitrate leaching from soil using
lysimeters was also investigated. Zeolite showed 10.23% to 88.42%
NH4
+ removal efficiency over a wide range of initial NH4
+
concentrations. Nitrate removal efficiency by SMZ was 32.26% to
82.26%. Field study results showed that Cp and SMZ significantly (p
< 0.05) reduced leachate NO3-N concentration compared to control.
There was no significant difference between maximum and mean
leachate NO3-N concentration of SMZ lysimeters and those of Cp
lysimeters.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: Alpinia galanga is rhizome, generally known as
Greater galangal and is selected for isolation of newer constituents
accountable for various therapeutic activities. Present study is
intended to isolate glycoside from Alpinia galanga rhizomes. Alpinia
galanga methanolic extract was column chromatograph and eluted
with ethyl acetate-methanol (99:1) to isolate compound β-Sitosterol
Diarabinoside. Herein, the isolation and structural elucidation of new
compound is described. Chemical investigation of methanolic extract
of rhizomes of Alpinia galanga furnished a new compound β-
Sitosterol Diarabinoside. The IR, NMR and MASS investigations of
isolated compound confirmed its structure as β-Sitosterol
Diarabinoside, which is isolated for the first time from a medicinal
plant or any synthetic source.
Abstract: Anaerobic digestion process is one of the alternative
methods to convert organic waste into methane gas which is a fuel
and energy source. Activities of various kinds of microorganisms are
the main factor for anaerobic digestion which produces methane gas.
Therefore, in this study a modified Anaerobic Baffled Reactor (ABR)
with working volume of 50 liters was designed to identify the
microorganisms through biogas production. The mixture of 75%
kitchen waste and 25% sewage sludge was used as substrate.
Observations on microorganisms in the ABR showed that there exists
a small amount of protozoa (5%) and fungi (2%) in the system, but
almost 93% of the microorganism population consists of bacteria. It
is definitely clear that bacteria are responsible for anaerobic
biodegradation of kitchen waste. Results show that in the
acidification zone of the ABR (front compartments of reactor) fast
growing bacteria capable of growth at high substrate levels and
reduced pH was dominant. A shift to slower growing scavenging
bacteria that grow better at higher pH was occurring towards the end
of the reactor. Due to the ability of activity in acetate environment the
percentages of Methanococcus, Methanosarcina and Methanotrix
were higher than other kinds of methane former in the system.
Abstract: Laboratory classes in Electrical Engineering are often hampered by safety issues, as students have to work on high voltage lines. One solution is to make use of virtual laboratory simulations, to help students understand the concepts taught in their coursework. In this context, we have conceived and implemented virtual lab experiments in connection with the study of earthing arrangements. In this work, software was developed, which aid student in understanding the working of a residual current device (RCD) in a TT earthing system. Various parameters, such as the earthing resistances, leakage currents and harmonics were included for a TT system with RCD connection.
Abstract: Traffic incident has bad effect on all parts of society
so controlling road networks with enough traffic devices could help
to decrease number of accidents, so using the best method for
optimum site selection of these devices could help to implement good
monitoring system. This paper has considered here important criteria
for optimum site selection of traffic camera based on aggregation
methods such as Bagging and Dempster-Shafer concepts. In the first
step, important criteria such as annual traffic flow, distance from
critical places such as parks that need more traffic controlling were
identified for selection of important road links for traffic camera
installation, Then classification methods such as Artificial neural
network and Decision tree algorithms were employed for
classification of road links based on their importance for camera
installation. Then for improving the result of classifiers aggregation
methods such as Bagging and Dempster-Shafer theories were used.
Abstract: Chemical vapor deposition method was used to
produce carbon nanotubes on an iron based catalyst from acetylene.
Gas-phase samples collected from the different positions of the tubular reactor were analyzed by GC/MS. A variety of species ranging from hydrogen to naphthalene were observed and changes in their concentrations were plotted against the reactor position. Briefly benzene, toluene, styrene, indene and naphthalene were the main
higher molecular weight species and vinylacetylene and diacetylene were the important intermediates. Nanotube characterization was performed by scanning electron microscopy and transmission electron microscopy.
Abstract: In this paper, the problem of finding the optimal
topological configuration of a deregulated distribution network is
considered. The new features of this paper are proposing a multiobjective
function and its application on deregulated distribution
networks for finding the optimal configuration. The multi-objective
function will be defined for minimizing total Energy Supply Costs
(ESC) and energy losses subject to load flow constraints. The
optimal configuration will be obtained by using Binary Genetic
Algorithm (BGA).The proposed method has been tested to analyze a
sample and a practical distribution networks.
Abstract: Researchers have long had trouble in measurement of
Exchangeable Sodium Ratio (ESR) at salt-affected soils. this
parameter are often determined using laborious and time consuming
laboratory tests, but it may be more appropriate and economical to
develop a method which uses a more simple soil salinity index. The
aim of this study was to determine the relationship between
exchangeable sodium ratio (ESR) and sodium adsorption ratio (SAR)
in some salt-affected soils of Khuzestan plain. To this purpose, two
experimental areas (S1, S2) of Khuzestan province-IRAN were
selected and four treatments with three replications by series of
double rings were applied. The treatments were included 25cm,
50cm, 75cm and 100cm water application. The statistical results of
the study indicated that in order to predict soil ESR based on soil
SAR the linear regression model ESR=0.2048+0.0066 SAR
(R2=0.53) & ESR=0.0564+0.0171 SAR (R2=0.76) can be
recommended in Pilot S1 and S2 respectively.
Abstract: This paper presents the experimental results on
ageing deterioration of silicone rubber outdoor polymer insulator
under salt water dip wheel test based on IEC 62217. In order to comparison effect of chemical contents, silicone rubber outdoor
polymer insulators having same configuration and leakage distant
from two manufactures were tested together continuously 30,000 test cycles. Many discharge activities were observed in during the test.
After 30,000 test cycles, in spite of same configuration, differences in
degree of surface aging were observed. Physical analysis such as
decreasing in hydrophobicity and increasing in hardness
measurement were measured on two-type tested specimen surface in order to confirm degree of surface ageing. Furthermore, chemical
analysis by ATR-FTIR to diagnose the chemical change of tested
specimen surface was conducted to confirm the physical analysis results.
Abstract: Tritium activity concentration in Danube river water
in Serbia has been determinate using a liquid scintillation counter
Quantulus 1220. During December 2010, water samples were taken
along the entire course of Danube through Serbia, from Hungarian-
Serbian to Romanian-Serbian border. This investigation is very
important because of the nearness of nuclear reactor Paks in
Hungary. Sample preparation was performed by standard test method
using Optiphase HiSafe 3 scintillation cocktail. We used a rapid
method for the preparation of environmental samples, without
electrolytic enrichment.
Abstract: 15 strains of oil-destructing microorganisms were
isolated from oil polluted soil of Western Kazakhstan. Strains 2-A
and 41-3 with the highest oil-destructing activities were chosen from
them. It was shown that these strains oxidized n-alkanes very well,
but isoalkanes, isoparaffin, cycloparaffin and heavy aromatic
compounds were destructed very slowly. These both strains were
tested as preparations for bioremediation of oil-polluted soil in model
and field experiments. The degree of utilizing of soil oil by this
preparation was 79-84 % in field experiments.
Abstract: The InAlGaN alloy has only recently began receiving
serious attention into its growth and application. High quality InGaN
films have led to the development of light emitting diodes (LEDs) and
blue laser diodes (LDs). The quaternary InAlGaN however, represents
a more versatile material since the bandgap and lattice constant can be
independently varied. We report an ultraviolet (UV) quaternary
InAlGaN multi-quantum wells (MQWs) LD study by using the
simulation program of Integrated System Engineering (ISE TCAD).
Advanced physical models of semiconductor properties were used in
order to obtain an optimized structure. The device performance which
is affected by piezoelectric and thermal effects was studied via
drift-diffusion model for carrier transport, optical gain and loss. The
optical performance of the UV LD with different numbers of quantum
wells was numerically investigated. The main peak of the emission
wavelength for double quantum wells (DQWs) was shifted from 358
to 355.8 nm when the forward current was increased. Preliminary
simulated results indicated that better output performance and lower
threshold current could be obtained when the quantum number is four,
with output power of 130 mW and threshold current of 140 mA.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.