Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: This paper presents the study of parameters affecting
the environment protection in the printing industry. The paper has
also compared LCA studies performed within the printing industry in
order to identify common practices, limitations, areas for
improvement, and opportunities for standardization. This comparison
is focused on the data sources and methodologies used in the printing
pollutants register. The presented concepts, methodology and results
represent the contribution to the sustainable development
management. Furthermore, the paper analyzes the result of the
quantitative identification of hazardous substances emitted in printing
industry of Novi Sad.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: Radio-frequency identification has entered as a beneficial means with conforming GS1 standards to provide the best solutions in the manufacturing area. It competes with other automated identification technologies e.g. barcodes and smart cards with regard to high speed scanning, reliability and accuracy as well. The purpose of this study is to improve production line-s performance by implementing RFID system in the manufacturing area on the basis of radio-frequency identification (RFID) system by 3D modeling in the program Cinema 4D R13 which provides obvious graphical scenes for users to portray their applications. Finally, with regard to improving system performance, it shows how RFID appears as a well-suited technology in a comparison of the barcode scanner to handle different kinds of raw materials in the production line base on logical process.
Abstract: Laboratory activities have produced benefits in
student learning. With current drives of new technology resources
and evolving era of education methods, renewal status of learning
and teaching in laboratory methods are in progress, for both learners
and the educators. To enhance learning outcomes in laboratory works
particularly in engineering practices and testing, learning via handson
by instruction may not sufficient. This paper describes and
compares techniques and implementation of traditional (expository)
with open-ended laboratory (problem-based) for two consecutive
cohorts studying environmental laboratory course in civil engineering
program. The transition of traditional to problem-based findings and
effect were investigated in terms of course assessment student
feedback survey, course outcome learning measurement and student
performance grades. It was proved that students have demonstrated
better performance in their grades and 12% increase in the course
outcome (CO) in problem-based open-ended laboratory style than
traditional method; although in perception, students has responded
less favorable in their feedback.
Abstract: The speech signal conveys information about the
identity of the speaker. The area of speaker identification is
concerned with extracting the identity of the person speaking the
utterance. As speech interaction with computers becomes more
pervasive in activities such as the telephone, financial transactions
and information retrieval from speech databases, the utility of
automatically identifying a speaker is based solely on vocal
characteristic. This paper emphasizes on text dependent speaker
identification, which deals with detecting a particular speaker from a
known population. The system prompts the user to provide speech
utterance. System identifies the user by comparing the codebook of
speech utterance with those of the stored in the database and lists,
which contain the most likely speakers, could have given that speech
utterance. The speech signal is recorded for N speakers further the
features are extracted. Feature extraction is done by means of LPC
coefficients, calculating AMDF, and DFT. The neural network is
trained by applying these features as input parameters. The features
are stored in templates for further comparison. The features for the
speaker who has to be identified are extracted and compared with the
stored templates using Back Propogation Algorithm. Here, the
trained network corresponds to the output; the input is the extracted
features of the speaker to be identified. The network does the weight
adjustment and the best match is found to identify the speaker. The
number of epochs required to get the target decides the network
performance.
Abstract: In this paper, we propose an energy efficient cluster
based communication protocol for wireless sensor network. Our
protocol considers both the residual energy of sensor nodes and the
distance of each node from the BS when selecting cluster-head. This
protocol can successfully prolong the network-s lifetime by 1)
reducing the total energy dissipation on the network and 2) evenly
distributing energy consumption over all sensor nodes. In this
protocol, the nodes with more energy and less distance from the BS
are probable to be selected as cluster-head. Simulation results with
MATLAB show that proposed protocol could increase the lifetime of
network more than 94% for first node die (FND), and more than 6%
for the half of the nodes alive (HNA) factor as compared with
conventional protocols.
Abstract: Wheat gluten hydrolyzates (WGHs) and anchovy fine
powder hydrolyzates (AFPHs) were produced at 300 MPa using
combinations of Flavourzyme 500MG (F), Alcalase 2.4L (A),
Marugoto E (M) and Protamex (P), and then were compared to those
produced at ambient pressure concerning the contents of soluble solid
(SS), soluble nitrogen and electrophoretic profiles. The contents of SS
in the WGHs and AFPHs increased up to 87.2% according to the
increase in enzyme number both at high and ambient pressure. Based
on SS content, the optimum enzyme combinations for one-, two-,
three- and four-enzyme hydrolysis were determined as F, FA, FAM
and FAMP, respectively. Similar trends were found for the contents of
total soluble nitrogen (TSN) and TCA-soluble nitrogen (TCASN). The
contents of SS, TSN and TCASN in the hydrolyzates together with
electrophoretic mobility maps indicates that the high-pressure
treatment of this study accelerated protein hydrolysis compared to
ambient-pressure treatment.
Abstract: The goal of this project is to design a system to
recognition voice commands. Most of voice recognition systems
contain two main modules as follow “feature extraction" and “feature
matching". In this project, MFCC algorithm is used to simulate
feature extraction module. Using this algorithm, the cepstral
coefficients are calculated on mel frequency scale. VQ (vector
quantization) method will be used for reduction of amount of data to
decrease computation time. In the feature matching stage Euclidean
distance is applied as similarity criterion. Because of high accuracy
of used algorithms, the accuracy of this voice command system is
high. Using these algorithms, by at least 5 times repetition for each
command, in a single training session, and then twice in each testing
session zero error rate in recognition of commands is achieved.
Abstract: Multi-agent system approach has proven to be an effective and appropriate abstraction level to construct whole models of a diversity of biological problems, integrating aspects which can be found both in "micro" and "macro" approaches when modeling this type of phenomena. Taking into account these considerations, this paper presents the important computational characteristics to be gathered into a novel bioinformatics framework built upon a multiagent architecture. The version of the tool presented herein allows studying and exploring complex problems belonging principally to structural biology, such as protein folding. The bioinformatics framework is used as a virtual laboratory to explore a minimalist model of protein folding as a test case. In order to show the laboratory concept of the platform as well as its flexibility and adaptability, we studied the folding of two particular sequences, one of 45-mer and another of 64-mer, both described by an HP model (only hydrophobic and polar residues) and coarse grained 2D-square lattice. According to the discussion section of this piece of work, these two sequences were chosen as breaking points towards the platform, in order to determine the tools to be created or improved in such a way to overcome the needs of a particular computation and analysis of a given tough sequence. The backwards philosophy herein is that the continuous studying of sequences provides itself important points to be added into the platform, to any time improve its efficiency, as is demonstrated herein.
Abstract: Investment in a constructed facility represents a cost in
the short term that returns benefits only over the long term use of the
facility. Thus, the costs occur earlier than the benefits, and the owners
of facilities must obtain the capital resources to finance the costs of
construction. A project cannot proceed without an adequate
financing, and the cost of providing an adequate financing can be
quite large. For these reasons, the attention to the project finance is an
important aspect of project management. Finance is also a concern to
the other organizations involved in a project such as the general
contractor and material suppliers. Unless an owner immediately and
completely covers the costs incurred by each participant, these
organizations face financing problems of their own. At a more
general level, the project finance is the only one aspect of the general
problem of corporate finance. If numerous projects are considered
and financed together, then the net cash flow requirements constitute
the corporate financing problem for capital investment. Whether
project finance is performed at the project or at the corporate level
does not alter the basic financing problem .In this paper, we will first
consider facility financing from the owner's perspective, with due
consideration for its interaction with other organizations involved in a
project. Later, we discuss the problems of construction financing
which are crucial to the profitability and solvency of construction
contractors. The objective of this paper is to present the steps utilized
to determine the best combination of minimum project financing.
The proposed model considers financing; schedule and maximum net
area .The proposed model is called Project Financing and Schedule
Integration using Genetic Algorithms "PFSIGA". This model
intended to determine more steps (maximum net area) for any project
with a subproject. An illustrative example will demonstrate the
feature of this technique. The model verification and testing are put
into consideration.
Abstract: The group mutual exclusion (GME) problem is an
interesting generalization of the mutual exclusion problem. In the
group mutual exclusion, multiple processes can enter a critical
section simultaneously if they belong to the same group. In the
extended group mutual exclusion, each process is a member of
multiple groups at the same time. As a result, after the process by
selecting a group enter critical section, other processes can select the
same group with its belonging group and can enter critical section at
the moment, so that it avoids their unnecessary blocking. This paper
presents a quorum-based distributed algorithm for the extended
group mutual exclusion problem. The message complexity of our
algorithm is O(4Q ) in the best case and O(5Q) in the worst case,
where Q is a quorum size.
Abstract: Perspective of food security in 21 century showed
shortage of food that production is faced to vital problem. Food
security strategy is applied longtime method to assess required food.
Meanwhile, nanotechnology revolution changes the world face.
Nanotechnology is adequate method utilize of its characteristics to
decrease environmental problems and possible further access to food
for small farmers. This article will show impact of production and
adoption of nanocrops on food security. Population is researchers of
agricultural research center of Esfahan province. The results of study
show that there was a relationship between uses, conversion,
distribution, and production of nanocrops, operative human
resources, operative circumstance, and constrains of usage of
nanocrops and food security. Multivariate regression analysis by
enter model shows that operative circumstance, use, production and
constrains of usage of nanocrops had positive impact on food security
and they determine in four steps 20 percent of it.
Abstract: The technical realization of data transmission using
glass fiber began after the development of diode laser in year 1962.
The erbium doped fiber amplifiers (EDFA's) in high speed networks
allow information to be transmitted over longer distances without
using of signal amplification repeaters. These kinds of fibers are
doped with erbium atoms which have energy levels in its atomic
structure for amplifying light at 1550nm. When a carried signal wave
at 1550nm enters the erbium fiber, the light stimulates the excited
erbium atoms which pumped with laser beam at 980nm as additional
light. The wavelength and intensity of the semiconductor lasers
depend on the temperature of active zone and the injection current.
The present paper shows the effect of the diode lasers temperature
and injection current on the optical amplification. From the results of
in- and output power one may calculate the max. optical gain by
erbium doped fiber amplifier.
Abstract: Mathematical, graphical and intuitive models are often
constructed in the development process of computational systems.
The Unified Modeling Language (UML) is one of the most popular
modeling languages used by practicing software engineers. This
paper critically examines UML models and suggests an augmented
use case view with the addition of new constructs for modeling
software. It also shows how a use case diagram can be enhanced. The
improved modeling constructs are presented with examples for
clarifying important design and implementation issues.
Abstract: The aim of this paper is to present a methodology in
three steps to forecast supply chain demand. In first step, various data
mining techniques are applied in order to prepare data for entering
into forecasting models. In second step, the modeling step, an
artificial neural network and support vector machine is presented
after defining Mean Absolute Percentage Error index for measuring
error. The structure of artificial neural network is selected based on
previous researchers' results and in this article the accuracy of
network is increased by using sensitivity analysis. The best forecast
for classical forecasting methods (Moving Average, Exponential
Smoothing, and Exponential Smoothing with Trend) is resulted based
on prepared data and this forecast is compared with result of support
vector machine and proposed artificial neural network. The results
show that artificial neural network can forecast more precisely in
comparison with other methods. Finally, forecasting methods'
stability is analyzed by using raw data and even the effectiveness of
clustering analysis is measured.
Abstract: Mobile agent has motivated the creation of a new
methodology for parallel computing. We introduce a methodology
for the creation of parallel applications on the network. The proposed
Mobile-Agent parallel processing framework uses multiple Javamobile
Agents. Each mobile agent can travel to the specified
machine in the network to perform its tasks. We also introduce the
concept of master agent, which is Java object capable of
implementing a particular task of the target application. Master agent
is dynamically assigns the task to mobile agents. We have developed
and tested a prototype application: Mobile Agent Based Parallel
Computing. Boosted by the inherited benefits of using Java and
Mobile Agents, our proposed methodology breaks the barriers
between the environments, and could potentially exploit in a parallel
manner all the available computational resources on the network.
This paper elaborates performance issues of a mobile agent for
parallel computing.
Abstract: Saudi Arabia is an arid country which depends on
costly desalination plants to satisfy the growing residential water
demand. Prediction of water demand is usually a challenging task
because the forecast model should consider variations in economic
progress, climate conditions and population growth. The task is
further complicated knowing that Mecca city is visited regularly by
large numbers during specific months in the year due to religious
occasions. In this paper, a neural networks model is proposed to
handle the prediction of the monthly and yearly water demand for
Mecca city, Saudi Arabia. The proposed model will be developed
based on historic records of water production and estimated visitors-
distribution. The driving variables for the model include annuallyvarying
variables such as household income, household density, and
city population, and monthly-varying variables such as expected
number of visitors each month and maximum monthly temperature.
Abstract: Risk of infectious disease outbreaks is related to the
hygiene among the population. To assess the actual risks and modify
the relevant emergency procedures if necessary, a hygiene survey
was conducted among undergraduate students on the Rhodes
University campus. Soap was available to 10.5% and only 26.8% of
the study participants followed proper hygiene in relation to food
consumption. This combination increases the risk of infectious
disease outbreaks at the campus. Around 83.6% were willing to wash
their hands if soap was provided. Procurement and availability of
soap in undergraduate residences on campus should be improved, as
the total cost is estimated at only 2000 USD per annum. Awareness
campaigns about food-related hygiene and the need for regular handwashing
with soap should be run among Rhodes University students.
If successful, rates of respiratory and hygiene-related diseases will be
decreased and emergency health management simplified.