Abstract: Results are presented from a combined experimental
and modeling study undertaken to understand the effect of fuel spray
angle on soot production in turbulent liquid spray flames. The
experimental work was conducted in a cylindrical laboratory furnace
at fuel spray cone angle of 30º, 45º and 60º. Soot concentrations
inside the combustor are measured by filter paper technique. The soot
concentration is modeled by using the soot particle number density
and the mass density based acetylene concentrations. Soot oxidation
occurred by both hydroxide radicals and oxygen molecules. The
comparison of calculated results against experimental measurements
shows good agreement. Both the numerical and experimental results
show that the peak value of soot and its location in the furnace
depend on fuel spray cone angle. An increase in spray angle enhances
the evaporating rate and peak temperature near the nozzle. Although
peak soot concentration increase with enhance of fuel spray angle but
soot emission from the furnace decreases.
Abstract: Distributed wireless sensor network consist on several
scattered nodes in a knowledge area. Those sensors have as its only
power supplies a pair of batteries that must let them live up to five
years without substitution. That-s why it is necessary to develop
some power aware algorithms that could save battery lifetime as
much as possible. In this is document, a review of power aware
design for sensor nodes is presented. As example of implementations,
some resources and task management, communication, topology
control and routing protocols are named.
Abstract: A 2-Degrees of freedom powered prosthetic wrist
actuator has been proposed that can provide the Abduction/Adduction
& Flexion/Extension movements of the human wrist. The basic
structure of the actuator is a Ball and Socket joint and the force is
transmitted from the DC geared servo motors to the joint through the
Bowden cables. The proposed design is capable of providing the
required DOF in both axes i.e. 85° & 90° in flexion extension axis.
The size and weight of the actuator lies within the ranges of an
average human being-s wrist.
Abstract: This paper mainly about the study on one of the
widely used error correcting codes that is Low parity check Codes
(LDPC). In this paper, the Regular LDPC code has been discussed
The LDPC codes explained in this paper is about the Regular Binary
LDPC codes or the Gallager.
Abstract: Reduction of Single Input Single Output (SISO) discrete systems into lower order model, using a conventional and an evolutionary technique is presented in this paper. In the conventional technique, the mixed advantages of Modified Cauer Form (MCF) and differentiation are used. In this method the original discrete system is, first, converted into equivalent continuous system by applying bilinear transformation. The denominator of the equivalent continuous system and its reciprocal are differentiated successively, the reduced denominator of the desired order is obtained by combining the differentiated polynomials. The numerator is obtained by matching the quotients of MCF. The reduced continuous system is converted back into discrete system using inverse bilinear transformation. In the evolutionary technique method, Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example.
Abstract: The aim of this paper is to present the role of
myotonometry in assessment muscle viscoelasticity by measurement
of force index (IF) and stiffness (S) at thigh muscle groups. The
results are used for improve the muscle training. The method is based
on mechanic impulse on the muscle group, that involve a muscle
response like acceleration, speed and amplitude curves. From these
we have information about elasticity, stiffness beginning from
mechanic oscillations of muscle tissue. Using this method offer the
possibility for monitoring the muscle capacity for produce mechanic
energy, that allows a efficiency of movement with a minimal tissue
deformation.
Abstract: With Power system movement toward restructuring along with factors such as life environment pollution, problems of transmission expansion and with advancement in construction technology of small generation units, it is expected that small units like wind turbines, fuel cells, photovoltaic, ... that most of the time connect to the distribution networks play a very essential role in electric power industry. With increase in developing usage of small generation units, management of distribution networks should be reviewed. The target of this paper is to present a new method for optimal management of active and reactive power in distribution networks with regard to costs pertaining to various types of dispersed generations, capacitors and cost of electric energy achieved from network. In other words, in this method it-s endeavored to select optimal sources of active and reactive power generation and controlling equipments such as dispersed generations, capacitors, under load tapchanger transformers and substations in a way that firstly costs in relation to them are minimized and secondly technical and physical constraints are regarded. Because the optimal management of distribution networks is an optimization problem with continuous and discrete variables, the new evolutionary method based on Ant Colony Algorithm has been applied. The simulation results of the method tested on two cases containing 23 and 34 buses exist and will be shown at later sections.
Abstract: In this paper back-propagation artificial neural
network (BPANN) with Levenberg–Marquardt algorithm is
employed to predict the limiting drawing ratio (LDR) of the deep
drawing process. To prepare a training set for BPANN, some finite
element simulations were carried out. die and punch radius, die arc
radius, friction coefficient, thickness, yield strength of sheet and
strain hardening exponent were used as the input data and the LDR
as the specified output used in the training of neural network. As a
result of the specified parameters, the program will be able to
estimate the LDR for any new given condition. Comparing FEM and
BPANN results, an acceptable correlation was found.
Abstract: In image processing and visualization, comparing two
bitmapped images needs to be compared from their pixels by matching
pixel-by-pixel. Consequently, it takes a lot of computational time
while the comparison of two vector-based images is significantly
faster. Sometimes these raster graphics images can be approximately
converted into the vector-based images by various techniques. After
conversion, the problem of comparing two raster graphics images
can be reduced to the problem of comparing vector graphics images.
Hence, the problem of comparing pixel-by-pixel can be reduced to
the problem of polynomial comparisons. In computer aided geometric
design (CAGD), the vector graphics images are the composition of
curves and surfaces. Curves are defined by a sequence of control
points and their polynomials. In this paper, the control points will be
considerably used to compare curves. The same curves after relocated
or rotated are treated to be equivalent while two curves after different
scaled are considered to be similar curves. This paper proposed an
algorithm for comparing the polynomial curves by using the control
points for equivalence and similarity. In addition, the geometric
object-oriented database used to keep the curve information has also
been defined in XML format for further used in curve comparisons.
Abstract: Whereas cellular wireless communication systems are
subject to short-and long-term fading. The effect of wireless channel
has largely been ignored in most of the teletraffic assessment
researches. In this paper, a mathematical teletraffic model is proposed
to estimate blocking and forced termination probabilities of cellular
wireless networks as a result of teletraffic behavior as well as the
outage of the propagation channel. To evaluate the proposed
teletraffic model, gamma inter-arrival and general service time
distributions have been considered based on wireless channel fading
effect. The performance is evaluated and compared with the classical
model. The proposed model is dedicated and investigated in different
operational conditions. These conditions will consider not only the
arrival rate process, but also, the different faded channels models.
Abstract: In this paper we present an adaptive method for image
compression that is based on complexity level of the image. The
basic compressor/de-compressor structure of this method is a multilayer
perceptron artificial neural network. In adaptive approach
different Back-Propagation artificial neural networks are used as
compressor and de-compressor and this is done by dividing the
image into blocks, computing the complexity of each block and then
selecting one network for each block according to its complexity
value. Three complexity measure methods, called Entropy, Activity
and Pattern-based are used to determine the level of complexity in
image blocks and their ability in complexity estimation are evaluated
and compared. In training and evaluation, each image block is
assigned to a network based on its complexity value. Best-SNR is
another alternative in selecting compressor network for image blocks
in evolution phase which chooses one of the trained networks such
that results best SNR in compressing the input image block. In our
evaluations, best results are obtained when overlapping the blocks is
allowed and choosing the networks in compressor is based on the
Best-SNR. In this case, the results demonstrate superiority of this
method comparing with previous similar works and JPEG standard
coding.
Abstract: In today-s era of plasma and laser cutting, machines using oxy-acetylene flame are also meritorious due to their simplicity and cost effectiveness. The objective to devise a Computer controlled Oxy-Fuel profile cutting machine arose from the increasing demand for metal cutting with respect to edge quality, circularity and lesser formation of redeposit material. The System has an 8 bit micro controller based embedded system, which assures stipulated time response. A new window based Application software was devised which takes a standard CAD file .DXF as input and converts it into numerical data required for the controller. It uses VB6 as a front end whereas MS-ACCESS and AutoCAD as back end. The system is designed around AT89C51RD2, powerful 8 bit, ISP micro controller from Atmel and is optimized to achieve cost effectiveness and also maintains the required accuracy and reliability for complex shapes. The backbone of the system is a cleverly designed mechanical assembly along with the embedded system resulting in an accuracy of about 10 microns while maintaining perfect linearity in the cut. This results in substantial increase in productivity. The observed results also indicate reduced inter laminar spacing of pearlite with an increase in the hardness of the edge region.
Abstract: In this paper, position vector of a partially null unit speed curve with respect to standard frame of Minkowski space-time is studied. First, it is proven that position vector of every partially null unit speed curve satisfies a vector differential equation of fourth order. In terms of solution of the differential equation, position vector of a partially null unit speed curve is expressed.
Abstract: Migration in breast cancer cell wound healing assay
had been studied using image fractal dimension analysis. The
migration of MDA-MB-231 cells (highly motile) in a wound healing
assay was captured using time-lapse phase contrast video microscopy
and compared to MDA-MB-468 cell migration (moderately motile).
The Higuchi fractal method was used to compute the fractal
dimension of the image intensity fluctuation along a single pixel
width region parallel to the wound. The near-wound region fractal
dimension was found to decrease three times faster in the MDA-MB-
231 cells initially as compared to the less cancerous MDA-MB-468
cells. The inner region fractal dimension was found to be fairly
constant for both cell types in time and suggests a wound influence
range of about 15 cell layer. The box-counting fractal dimension
method was also used to study region of interest (ROI). The MDAMB-
468 ROI area fractal dimension was found to decrease
continuously up to 7 hours. The MDA-MB-231 ROI area fractal
dimension was found to increase and is consistent with the behavior
of a HGF-treated MDA-MB-231 wound healing assay posted in the
public domain. A fractal dimension based capacity index has been
formulated to quantify the invasiveness of the MDA-MB-231 cells in
the perpendicular-to-wound direction. Our results suggest that image
intensity fluctuation fractal dimension analysis can be used as a tool
to quantify cell migration in terms of cancer severity and treatment
responses.
Abstract: As days go by, we hear more and more about HIV,
Ebola, Bird Flu and other dreadful viruses which were unknown a
few decades ago. In both detecting and fighting viral diseases
ordinary methods have come across some basic and important
difficulties. Vaccination is by a sense introduction of the virus to the
immune system before the occurrence of the real case infection. It is
very successful against some viruses (e.g. Poliomyelitis), while
totally ineffective against some others (e.g. HIV or Hepatitis-C). On
the other hand, Anti-virus drugs are mostly some tools to control and
not to cure a viral disease. This could be a good motivation to try
alternative treatments. In this study, some key features of possible
physical-based alternative treatments for viral diseases are presented.
Electrification of body parts or fluids (especially blood) with micro
electric signals with adjusted current or frequency is also studied. The
main approach of this study is to find a suitable energy field, with
appropriate parameters that are able to kill or deactivate viruses. This
would be a lengthy, multi-disciplinary research which needs the
contribution of virology, physics, and signal processing experts. It
should be mentioned that all the claims made by alternative cures
researchers must be tested carefully and are not advisable at the time
being.
Abstract: The research study evaluated the performance of
irrigation system by using special scientific tools like Remote
Sensing and GIS technology, so that proper measurements could be
taken for the sustainable agriculture and water management.
Different performance evaluation parameters had been calculated for
the purposed data was gathered from field investigation and different
government and private organizations. According to the calculations,
organic matter ranges from 0.19% (low value) to 0.76% (high value).
In flat irrigation system for wheat yield ranges from 3347.16 to
5260.39 kg/ha, while the total water applied to wheat crop ranges
from 252.94 to 279.19 mm and WUE ranges from 13.07 to 18.37
kg/ha/mm. For rice yield ranges from 3347.47 to 5433.07 kg/ha with
total water supplied to rice crop ranges from 764.71 to 978.15 mm
and WUE ranges from 3.49 to 5.71 kg/ha/mm. Similarly, in raised
bed system wheat yield ranges from 4569.13 to 6008.60 kg/ha, total
water supplied ranges from 158.87 to 185.09 mm and WUE ranges
from 27.20 to 33.54 kg/ha/mm while in rice crop, yield ranges from
5285.04 to 6716.69 kg/ha, total water supplied ranges from 600.72 to
755.06 mm and WUE ranges from 6.41 to 10.05 kg/ha/mm. Almost
51.3% water saving is observed in bed irrigation system as compared
to flat system. Less water supplied to beds is more affective as its
WUE value is higher than flat system where more water is supplied
in both the seasons. Similarly, RWS values show that maximum
water deficit while minimum area is getting adequate water supply.
Greater yield is recorded in bed system as plant per square meter is
more in bed system in comparison of flat system Thus, the integration
of GIS tools to regularly compute performance indices could provide
irrigation managers with the means for managing efficiently the
irrigation system.
Abstract: β-Glucosidase is an important enzyme for production
of ethanol from lignocellulose. With hydrolytic activity on
cellooligosaccharides, especially cellobiose, β-glucosidase removes
product inhibitory effect on cellulases and forms fermentable sugars.
In this study, β-glucosidase encoding gene (BGL1) from traditional
starter yeast Saccharomycosis fibuligera BMQ908 was cloned and
expressed in Pichia pastoris. BGL1 of S. fibuligera BMQ 908 shared
98% nucleotide homology with the closest GenBank sequence
(M22475) but identity in amino-acid sequences of catalytic domains.
Recombinant plasmid pPICZαA/BGL1 containing the sequence
encoding BGL1 mature protein and α-factor secretion signal was
constructed and transformed into methylotrophic yeast P. pastoris by
electroporation. The recombinant strain produced single extracellular
protein with molecular weight of 120 kDa and cellobiase activity of
60 IU/ml. The optimum pH of the recombinant β-glucosidase was 5.0
and the optimum temperature was 50°C.
Abstract: Delivering course material via a virtual environment
is beneficial to today-s students because it offers the interactivity,
real-time interaction and social presence that students of all ages
have come to accept in our gaming rich community. It is essential
that the Net Generation also known as Generation Why, have
exposure to learning communities that encompass interactivity to
form social and educational connections. As student and professor
become interconnected through collaboration and interaction in a
virtual learning space, relationships develop and students begin to
take on an individual identity. With this in mind the research project
was developed to investigate the use of virtual environments on
student satisfaction and the effectiveness of course delivery.
Furthermore, the project was designed to integrate both interactive
(real-time) classes conducted in the Virtual Reality (VR)
environment while also creating archived VR sessions for student use
in retaining and reviewing course content.
Abstract: Since the European renewable energy directives set the
target for 22.1% of electricity generation to be supplied by 2010
[1], there has been increased interest in using green technologies
also within the urban enviroment. The most commonly considered
installations are solar thermal and solar photovoltaics. Nevertheless,
as observed by Bahaj et al. [2], small scale turbines can reduce the
built enviroment related CO2 emissions. Thus, in the last few years,
an increasing number of manufacturers have developed small wind
turbines specifically designed for the built enviroment. The present
work focuses on the integration into architectural systems of such
installations and presents a survey of successful case studies.
Abstract: This paper is introduced a modification to Diffie-
Hellman protocol to be applicable on the decimal numbers, which
they are the numbers between zero and one. For this purpose we
extend the theory of the congruence. The new congruence is over
the set of the real numbers and it is called the “real congruence"
or the “real modulus". We will refer to the existing congruence by
the “integer congruence" or the “integer modulus". This extension
will define new terms and redefine the existing terms. As the
properties and the theorems of the integer modulus are extended as
well. Modified Diffie-Hellman key exchange protocol is produced a
sharing, secure and decimal secret key for the the cryptosystems that
depend on decimal numbers.