Abstract: High-speed infrared vertical-cavity surface-emitting laser diodes (VCSELs) with Cu-plated heat sinks were fabricated and tested. VCSELs with 10 mm aperture diameter and 4 mm of electroplated copper demonstrated a -3dB modulation bandwidth (f-3dB) of 14 GHz and a resonance frequency (fR) of 9.5 GHz at a bias current density (Jbias) of only 4.3 kA/cm2, which corresponds to an improved f-3dB2/Jbias ratio of 44 GHz2/kA/cm2. At higher and lower bias current densities, the f-3dB2/ Jbias ratio decreased to about 30 GHz2/kA/cm2 and 18 GHz2/kA/cm2, respectively. Examination of the analogue modulation response demonstrated that the presented VCSELs displayed a steady f-3dB/ fR ratio of 1.41±10% over the whole range of the bias current (1.3Ith to 6.2Ith). The devices also demonstrated a maximum modulation bandwidth (f-3dB max) of more than 16 GHz at a bias current less than the industrial bias current standard for reliability by 25%.
Abstract: Dense wavelength division multiplexing (DWDM) technology requires tight specification and therefore measurement of wavelength accuracy and stability of the telecommunication lasers. Thus, calibration of the used Optical Spectrum Analyzers (OSAs) that are used to measure wavelength is of a great importance. Proficiency testing must be performed on such measuring activity to insure the accuracy of the measurement results. In this paper, a new comparison scheme is introduced to test the performance of such calibrations. This comparison scheme is implemented between NIS-Egypt and NMISA-South Africa for the calibration of the wavelength scale of an OSA. Both institutes employ reference gas cell to calibrate OSA according to the standard IEC/ BS EN 62129 (2006). The result of this comparison is compiled in this paper.
Abstract: In this paper, conventional laser Keratoplasty surgeries in the human eye are studied. For this purpose, a validated 3D finite volume model of the human eye is introduced. In this model the fluid flow has also been considered. The discretized domain of the human eye incorporates a bio-heat transfer equation coupled with a Boussinesq equation. Both continuous and pulsed lasers have been modeled and the results are compared. Moreover, two different conventional surgical positions that are upright and recumbent are compared for these laser therapies. The simulation results show that in these conventional surgeries, the temperature rises above the critical values at the laser insertion areas. However, due to the short duration and the localized nature, the potential damages are restricted to very small regions and can be ignored. The conclusion is that the present day lasers are acceptably safe to the human eye.
Abstract: The principle of all-silicon Raman lasers for an
output wavelength of 1.3 μm is presented, which employs
quasi-phase-matched structures and resonators to enhance the output
power. 1.3-μm laser beams for GE-PONs in FTTH systems generated
from a silicon device are very important because such a silicon device
can be monolithically integrated with the silicon planar lightwave
circuits (Si PLCs) used in the GE-PONs. This reduces the device
fabrication processes and time and also optical losses at the junctions
between optical waveguides of the Si PLCs and Si laser devices
when compared with 1.3-μm III-V semiconductor lasers set on the
Si PLCs employed at present. We show that the quasi-phase-matched
Si Raman laser with resonators can produce about 174 times larger
laser power at 1.3 μm (at maximum) than that without resonators
for a Si waveguide of Raman gain 20 cm/GW and optical loss 1.2
dB/cm, pumped at power 10 mW, where the length of the waveguide
is 3 mm and its cross-section is (1.5 μm)2.
Abstract: Composite materials are one answer to the growing demand for materials with better parameters of construction and exploitation. Composite materials also permit conscious shaping of desirable properties to increase the extent of reach in the case of metals, ceramics or polymers. In recent years, composite materials have been used widely in aerospace, energy, transportation, medicine, etc. Fiber-reinforced composites including carbon fiber, glass fiber and aramid fiber have become a major structural material. The typical defect during manufacture and operation is delamination damage of layered composites. When delamination damage of the composites spreads, it may lead to a composite fracture. One of the many methods used in non-destructive testing of composites is active infrared thermography. In active thermography, it is necessary to deliver energy to the examined sample in order to obtain significant temperature differences indicating the presence of subsurface anomalies. To detect possible defects in composite materials, different methods of thermal stimulation can be applied to the tested material, these include heating lamps, lasers, eddy currents, microwaves or ultrasounds. The use of a suitable source of thermal stimulation on the test material can have a decisive influence on the detection or failure to detect defects. Samples of multilayer structure carbon composites were prepared with deliberately introduced defects for comparative purposes. Very thin defects of different sizes and shapes made of Teflon or copper having a thickness of 0.1 mm were screened. Non-destructive testing was carried out using the following sources of thermal stimulation, heating lamp, flash lamp, ultrasound and eddy currents. The results are reported in the paper.
Abstract: This paper presents an investigation of the fabrication of the optical devices in terms of their characteristics based on the use of the electromagnetic waves. Planar waveguides are used to examine the field modes (bound modes) and the parameters required for this structure. The modifications are conducted on surface plasmons based waveguides. Simple symmetric dielectric slab structure is used and analyzed in terms of transverse electric mode (TE-Mode) and transverse magnetic mode (TM-Mode. The paper presents mathematical and numerical solutions for solving simple symmetric plasmons and provides simulations of surface plasmons for field confinement. Asymmetric TM-mode calculations for dielectric surface plasmons are also provided.
Abstract: Solar lentigines appear predominantly on chronically sun-exposed areas of skin, such as the face and the back of the hands. Among the several ways to lentigines treatment, quality-switched lasers are well-known effective treatment for removing solar lentigines. The present pilot study was therefore designed to assess the efficacy of quality-switched ruby laser treatment of such lentigines compare between pretreatment and posttreatment of skin brightness. Twenty-two adults with chronic sun-damaged skin (mean age 52.8 years, range 37–74 years) were treated at the Korean site. A 694 nm Q-switched ruby laser was used, with the energy density set from 1.4 to 12.5 J/cm2, to treat solar lentigines. Average brightness of skin color before ruby laser treatment was 137.3 and its skin color was brightened after ruby laser treatment by 150.5. Also, standard deviation of skin color was decreased from 17.8 to 16.4. Regarding the multivariate model, age and energy were identified as significant factors for skin color brightness change in lentigo depigmentation by ruby laser treatment. Their respective odds ratios were 1.082 (95% CI, 1.007–1.163), and 1.431 (95% CI, 1.051–1.946). Lentigo depigmentation treatment using ruby lasers resulted in a high performance in skin color brightness. Among the relative factors involve with ruby laser treatment, age and energy were the most effective factors which skin color change to brighter than pretreatment.
Abstract: Analytical formula for the optical gain based on a
simple parabolic-band by introducing theoretical expressions for the
quantized energy is presented. The model used in this treatment take
into account the effects of intraband relaxation. It is shown, as a
result, that the gain for the TE mode is larger than that for TM mode
and the presence of acceptor impurity increase the peak gain.
Abstract: In this paper, synchronization of multiple chaotic
semiconductor lasers is achieved by appealing to complex system
theory. In particular, we consider dynamical networks composed by
semiconductor laser, as interconnected nodes, where the interaction
in the networks are defined by coupling the first state of each node.
An interest case is synchronized with master-slave configuration in
star topology. Nodes of these networks are modeled for the laser and
simulate by Matlab. These results are applicable to private
communication.
Abstract: We report on the use of strong external optical
feedback to enhance the modulation response of semiconductor lasers
over a frequency passband around modulation frequencies higher
than 60 GHz. We show that this modulation enhancement is a type of
photon-photon resonance (PPR) of oscillating modes in the external
cavity formed between the laser and the external reflector. The study
is based on a time-delay rate equation model that takes into account
both the strong feedback and multiple reflections in the external
cavity. We examine the harmonic and intermodulation distortions
associated with single and two-tone modulations in the mm-wave
band of the resonant modulation. We show that compared with
solitary lasers modulated around the carrier-photon resonance
frequency, the present mm-wave modulated signal has lower
distortions.
Abstract: A novel method to produce a fast high voltage solid
states switch using Insulated Gate Bipolar Transistors (IGBTs) is
presented for discharge-pumped gas lasers. The IGBTs are connected
in series to achieve a high voltage rating. An avalanche transistor is
used as the gate driver. The fast pulse generated by the avalanche
transistor quickly charges the large input capacitance of the IGBT,
resulting in a switch out of a fast high-voltage pulse. The switching
characteristic of fast-high voltage solid state switch has been estimated
in the multi-stage series-connected IGBT with the applied voltage of
several tens of kV. Electrical circuit diagram and the mythology of
fast-high voltage solid state switch as well as experimental results
obtained are presented.
Abstract: The 1/f noise investigation in nanoscale light-emitting
diodes and lasers, based on GaAs and alloys, is presented here.
Leakage and additional (to recombination through quantum wells
and/or dots) nonlinear currents were detected and it was shown that
these currents are the main source of the 1/f noise in devices studied.
Abstract: The detection of environmental gases, 12CO2, 13CO2,
and CH4, using near-infrared semiconductor lasers with a short
laser path length is studied by means of wavelength-modulation
spectroscopy. The developed system is compact and has high
sensitivity enough to detect the absorption peaks of isotopic 13CO2
of a 3-% CO2 gas at 2 μm with a path length of 2.4 m, where
its peak size is two orders of magnitude smaller than that of the
ordinary 12CO2 peaks. In addition, the detection of 12CO2 peaks of
a 385-ppm (0.0385-%) CO2 gas in the air is made at 2 μm with a
path length of 1.4 m. Furthermore, in pursuing the detection of an
ancient environmental CH4 gas confined to a bubble in ice at the
polar regions, measurements of the absorption spectrum for a trace
gas of CH4 in a small area are attempted. For a 100-% CH4 gas
trapped in a ∼ 1 mm3 glass container, the absorption peaks of CH4
are obtained at 1.65 μm with a path length of 3 mm, and also the
gas pressure is extrapolated from the measured data.
Abstract: A laser is essentially an optical oscillator consisting of a resonant cavity, an amplifying medium and a pumping source. In semiconductor diode lasers, the cavity is created by the boundary between the cleaved face of the semiconductor crystal and air, and has reflective properties as a result of the differing refractive indices of the two media. For a GaAs-air interface a reflectance of 0.3 is typical and therefore the length of the semiconductor junction forms the resonant cavity. To prevent light being emitted in unwanted directions from the junction, sides perpendicular to the required direction are roughened. The objective of this work is to simulate the optical resonator Fabry-Perot and explore its main characteristics, such as FSR, finesse, linewidth, transmission and so on, that describe the performance of resonator.
Abstract: In this paper, the absorption and fluorescence
emission spectra of Yb:Y3Al5O12 (YAG)(25 at%) crystal as a disk
laser medium are measured at high temperature (300-450K). The
absorption and emission cross sections of Yb:YAG crystal are
determined using Reciprocity method. Temperature dependence of
941nm absorption cross section and 1031nm emission cross section
is extracted in the range of 300-450K. According to our experimental
results, an exponential temperature dependence between 300K and
450K is acquired for the 1031nm peak emission cross section and
also for 941nm peak absorption cross section of Yb:YAG crystal.
These results could be used for simulation and design of high power
highly doped Yb:YAG thin disk lasers.
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: Improving the performance of the QCL through block diagram as well as mathematical models is the main scope of this paper. In order to enhance the performance of the underlined device, the mathematical model parameters are used in a reliable manner in such a way that the optimum behavior was achieved. These parameters play the central role in specifying the optical characteristics of the considered laser source. Moreover, it is important to have a large amount of radiated power, where increasing the amount of radiated power represents the main hopping process that can be predicted from the behavior of quantum laser devices. It was found that there is a good agreement between the calculated values from our mathematical model and those obtained with VisSim and experimental results. These demonstrate the strength of mplementation of both mathematical and block diagram models.
Abstract: We theoretically investigate the effects of frequency
detuning and injection power on the nonlinear dynamics of DFB
lasers under dual external optical injection.
Abstract: Encoded information based on synchronization of coupled chaotic Nd:YAG lasers in master-slave configuration is numerically studied. Encoding, transmission, and decoding of information in optical chaotic communication with a single channel is presented. We analyze the robustness of the encrypted audio transmission in a channel noise. In order to illustrate this synchronization robustness, we present two cases of study: synchronization and transmission with a single channel without and with noise in the channel.