Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: Compositions of different molar ratios of
polymethylmethacrylate-co-methacrylic acid (PMMA-co-MAA)
were synthesized via free-radical polymerization. Polymer coated
surfaces have been produced on silicon wafers. Coated samples were
analyzed by atomic force microscopy (AFM). The results have shown
that the roughness of the surfaces have increased by increasing the
molar ratio of monomer methacrylic acid (MAA). This study reveals
that the gradual increase in surface roughness is due to the fact that
carboxylic functional groups have been generated by MAA segments.
Such surfaces can be desirable platforms for fabrication of the
biosensors for detection of the viruses and diseases.
Abstract: An existing RC building in Madinah is seismically
evaluated with and without infill wall. Four model systems have been
considered i.e. model I (no infill), model IIA (strut infill-update from
field test), model IIB (strut infill- ASCE/SEI 41) and model IIC (strut
infill-Soft storey- ASCE/SEI 41). Three dimensional pushover
analyses have been carried out using SAP2000 software
incorporating inelastic material behavior for concrete, steel and infill
walls. Infill wall has been modeled as equivalent strut according to
suggested equation matching field test measurements and to the
ASCE/SEI 41 equation. The effect of building modeling on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madinah area has been investigated. The
response modification factor (R) for the 5 story RC building is
evaluated from capacity and demand spectra (ATC-40) for the
studied models. The results are summarized and discussed.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: This paper presents analysis and design of a wideband
Wilkinson power divider for wireless applications. The design is
accomplished by transforming the lengths and impedances of the
quarter wavelength sections of the conventional Wilkinson power
divider into U-shaped sections. The designed power divider is
simulated by using ADS Agilent technologies and CST microwave
studio software. It is shown that the proposed power divider has
simple topology and good performances in terms of insertion loss,
port matching and isolation at all operating frequencies (1.8 GHz,
2.45 GHz and 3.55 GHz).
Abstract: Lightweight design represents an important key to
successful implementation of energy-saving, fuel-efficient and
environmentally friendly means of transport in the aerospace and
automotive industry. In this context the use of carbon fibre reinforced
plastics (CFRP) which are distinguished by their outstanding
mechanical properties at relatively low weight, promise significant
improvements. Due to the reduction of the total mass, with the
resulting lowered fuel or energy consumption and CO2 emissions
during the operational phase, commercial aircraft will increasingly be
made of CFRP. An auspicious technology for the efficient and
economic production of high performance thermoset composites and
hybrid structures for future lightweight applications is the
combination of carbon fibre sheet moulding compound, tailored
continuous carbon fibre reinforcements and metallic components in a
one-shot pressing and curing process. This paper deals with a hybrid
composite technology for aerospace industries, which was developed
with the help of a special innovation and development system.
Abstract: An exploration of the related literature reveals that all
instruction methods aim at training autonomous learners. After the
turn of second language pedagogy toward learner-oriented strategies,
learners’ needs were more focused. Yet; the historical, social and
political aspects of learning were still neglected. The present study
investigates the notion of autonomous learning and explains its
various facets from a pedagogical point of view. Furthermore;
different elements, fields and scopes of autonomous learning will be
explored. After exploring different aspects of autonomy, it is
postulated that liberatory autonomy is highlighted since it not only
covers social autonomy but also reveals learners’ capabilities and
human potentials. It is also recommended that learners consider
different elements of autonomy such as motivation, knowledge,
confidence, and skills.
Abstract: In the present study, mixed convection in a horizontal
rectangular duct using Al2O3 is numerically investigated. The effects
of different Rayleigh number, Reynolds number and radiation on
flow and heat transfer characteristics are studied in detail. This study
covers Rayleigh number in the range of 2 × 10^6 ≤ Ra ≤ 2 × 10^7 and
Reynolds number in the range of 100 ≤ Re ≤ 1100. Results reveal that
the Nusselt number increases as Reynolds and Rayleigh numbers
increase. It is also found that the dimensionless temperature
distribution increases as Rayleigh number increases.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: Currently, thorium fuel has been especially noticed
because of its proliferation resistance than long half-life alpha emitter
minor actinides, breeding capability in fast and thermal neutron flux
and mono-isotopic naturally abundant. In recent years, efficiency of
minor actinide burning up in PWRs has been investigated. Hence, a
minor actinide-contained thorium based fuel matrix can confront both
proliferation resistance and nuclear waste depletion aims. In the
present work, minor actinide depletion rate in a CANDU-type nuclear
core modeled using MCNP code has been investigated. The obtained
effects of minor actinide load as mixture of thorium fuel matrix on
the core neutronics has been studied with comparing presence and
non-presence of minor actinide component in the fuel matrix.
Depletion rate of minor actinides in the MA-contained fuel has been
calculated using different power loads. According to the obtained
computational data, minor actinide loading in the modeled core
results in more negative reactivity coefficients. The MA-contained
fuel achieves less radial peaking factor in the modeled core. The
obtained computational results showed 140 kg of 464 kg initial load
of minor actinide has been depleted in during a 6-year burn up in 10
MW power.
Abstract: This paper provides a comparative study on the
performances of standard PID and adaptive PID controllers tested on
travel angle of a 3-Degree-of-Freedom (3-DOF) Quanser bench-top
helicopter. Quanser, a well-known manufacturer of educational
bench-top helicopter has developed Proportional Integration
Derivative (PID) controller with Linear Quadratic Regulator (LQR)
for all travel, pitch and yaw angle of the bench-top helicopter. The
performance of the PID controller is relatively good; however, its
performance could also be improved if the controller is combined
with adaptive element. The objective of this research is to design
adaptive PID controller and then compare the performances of the
adaptive PID with the standard PID. The controller design and test is
focused on travel angle control only. Adaptive method used in this
project is self-tuning controller, which controller’s parameters are
updated online. Two adaptive algorithms those are pole-placement
and deadbeat have been chosen as the method to achieve optimal
controller’s parameters. Performance comparisons have shown that
the adaptive (deadbeat) PID controller has produced more desirable
performance compared to standard PID and adaptive (poleplacement).
The adaptive (deadbeat) PID controller attained very fast
settling time (5 seconds) and very small percentage of overshoot (5%
to 7.5%) for 10° to 30° step change of travel angle.
Abstract: Periventricular Leukomalacia (PVL) is a White Matter
Injury (WMI) of preterm neonatal brain. Objectives of the study were
to assess the neuro-developmental outcome at one year of age and to
determine a good protocol of cranial ultrasonography to detect PVL.
Two hundred and sixty four preterm neonates were included in the
study. Series of cranial ultrasound scans were done by using a
dedicated neonatal head probe 4-10 MHz of Logic e portable
ultrasound scanner. Clinical history of seizures, abnormal head
growth (hydrocephalus or microcephaly) and developmental
milestones were assessed and neurological examinations were done
until one year of age. Among live neonates, 57% who had cystic PVL
(Grades 2 and 3) manifested as cerebral palsy. In conclusion cystic
PVL has permanent neurological disabilities like cerebral palsy.
Good protocol of real time cranial ultrasonography to detect PVL is
to perform scans at least once a week until one month and at term (40
weeks of gestation).
Abstract: Cross flow water tube heat exchanger can be designed
and made operational using methods of model building and
simulation of the system. This paper projects the design and
development of a model of cross flow water tube heat-exchanger
system, simulation and validation of control analysis of different
tuning methods. Feedback and override control system is developed
using inputs acquired with the help of sensory system. A
mathematical model is formulated for analysis of system behaviour.
The temperature is regulated at the desired set point automatically.
Abstract: Nowadays, Photovoltaic-PV Farms/ Parks and large
PV-Smart Grid Interface Schemes are emerging and commonly
utilized in Renewable Energy distributed generation. However, PVhybrid-
Dc-Ac Schemes using interface power electronic converters
usually has negative impact on power quality and stabilization of
modern electrical network under load excursions and network fault
conditions in smart grid. Consequently, robust FACTS based
interface schemes are required to ensure efficient energy utilization
and stabilization of bus voltages as well as limiting switching/fault
onrush current condition. FACTS devices are also used in smart grid-
Battery Interface and Storage Schemes with PV-Battery Storage
hybrid systems as an elegant alternative to renewable energy
utilization with backup battery storage for electric utility energy and
demand side management to provide needed energy and power
capacity under heavy load conditions. The paper presents a robust
interface PV-Li-Ion Battery Storage Interface Scheme for
Distribution/Utilization Low Voltage Interface using FACTS
stabilization enhancement and dynamic maximum PV power tracking
controllers.
Digital simulation and validation of the proposed scheme is done
using MATLAB/Simulink software environment for Low Voltage-
Distribution/Utilization system feeding a hybrid Linear-Motorized
inrush and nonlinear type loads from a DC-AC Interface VSC-6-
pulse Inverter Fed from the PV Park/Farm with a back-up Li-Ion
Storage Battery.
Abstract: TiO2 thin films have been prepared by the sol-gel dipcoating
technique in order to elaborate antireflective thin films for
monocrystalline silicon (mono-Si). The titanium isopropoxyde was
chosen as a precursor with hydrochloric acid as a catalyser for
preparing a stable solution. The optical properties have been tailored
with varying the solution concentration, the withdrawn speed, and the
heat-treatment. We showed that using a TiO2 single layer with 64.5
nm in thickness, heat-treated at 450°C or 300°C reduces the mono-Si
reflection at a level lower than 3% over the broadband spectral
domains [669-834] nm and [786-1006] nm respectively. Those latter
performances are similar to the ones obtained with double layers of
low and high refractive index glasses respectively.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: In this study, we are interested in a species of the
family of Asteraceae (Tagetes erecta). This family is considered as a
source of antimicrobial extracts with strong capacity. The extraction
of the flavonoids is carried out by the method of liquid/liquid with the
use of successive solvents. Afterwards, we evaluated the biological
activity of the flavonoids on five pathogenic bacterial stocks such as
Escherichia coli, Bacillus subtilis, Klebsiella pneumoniae,
Pseudomonas aeruginosa and Staphylococcus aureus and two stocks
of yeasts to knowing Candida albicans) and Saccharomyces
cerevisiae, by employing the method of the aromatogramme starting
from a solid disc. The result of the antimicrobial activity shows an
action and a variable degree of sensitivity according to bacterial
stocks tested. It will be noted that the flavonoids have an inhibiting
effect on E. coli, B. subtilis, K. pneumoniae and S. aureus. But a
resistance with respect to the extract by P. aeruginosa, C. albicans
and S. cerevisiae is to be mentioned.
Abstract: Endowed of renewable energy sources (RES) are the
advantages of ASEAN, but they are using a low amount of RES only
to generate electricity because their primary energy sources are fossil
and coal. The cost of purchasing fossil and coal is cheaper now, but it
might be expensive soon, as it will be depleted sooner and after.
ASEAN showed that the RES are convenient to be implemented.
Some country in ASEAN has huge renewable energy sources
potential and use. The primary aim of this project is to assist ASEAN
countries in preparing the renewable energy and to guide the policies
for RES in the more upright direction. The Green-Y model will help
ASEAN government to study and forecast the economic concept,
including feed-in tariff.
Abstract: At present, the evaluation of voltage stability
assessment experiences sizeable anxiety in the safe operation of
power systems. This is due to the complications of a strain power
system. With the snowballing of power demand by the consumers
and also the restricted amount of power sources, therefore, the system
has to perform at its maximum proficiency. Consequently, the
noteworthy to discover the maximum ability boundary prior to
voltage collapse should be undertaken. A preliminary warning can be
perceived to evade the interruption of power system’s capacity. The
effectiveness of line voltage stability indices (LVSI) is differentiated
in this paper. The main purpose of the indices used is to predict the
proximity of voltage instability of the electric power system. On the
other hand, the indices are also able to decide the weakest load buses
which are close to voltage collapse in the power system. The line
stability indices are assessed using the IEEE 14 bus test system to
validate its practicability. Results demonstrated that the implemented
indices are practically relevant in predicting the manifestation of
voltage collapse in the system. Therefore, essential actions can be
taken to dodge the incident from arising.