Abstract: Stress Corrosion Crack (SCC) in pipeline is a type of
environmentally assisted cracking (EAC), since its discovery in 1965
as a possible cause of failure in pipeline, SCC has caused, on
average, one of two failures per year in the U.S, According to the
NACE SCC DA a pipe line segment is considered susceptible to SCC
if all of the following factors are met: The operating stress exceeds
60% of specified minimum yield strength (SMYS), the operating
temperature exceeds 38°C, the segment is less than 32 km
downstream from a compressor station, the age of the pipeline is
greater than 10 years and the coating type is other than Fusion
Bonded Epoxy(FBE). In this paper as a practical experience in
NISOC, Direct Assessment (DA) Method is used for identification
SCC defect in unpiggable pipeline located downstream of
compressor station.
Abstract: Kuosheng nuclear power plant (NPP) is a BWR/6 type
NPP and located on the northern coast of Taiwan. First, Kuosheng
NPP TRACE model were developed in this research. In order to assess
the system response of Kuosheng NPP TRACE model, startup tests
data were used to evaluate Kuosheng NPP TRACE model. Second, the
overpressurization transient analysis of Kuosheng NPP TRACE model
was performed. Besides, in order to confirm the mechanical property
and integrity of fuel rods, FRAPTRAN analysis was also performed in
this study.
Abstract: In this paper, the effect of WC-12Co particle
temperature in HVOF thermal spraying process on the coating
thickness has been studied. The statistical results show that the spray
distance and oxygen-to-fuel ratio are effective factors on particle
characterization and thickness of HVOF thermal spraying coatings.
Spray Watch diagnostic system, scanning electron microscopy
(SEM), X-ray diffraction and thickness measuring system were used
for this purpose.
Abstract: Mech-Degla, Degla-Beida and Frezza are the date
(Phoenix dactylifera L.) common varieties with a more or less good
availability and feeble trade value. Some morphologic and
physicochemical factors were determined. Results show that the
whole date weight is significantly different (P= 95%) concerning
Mech-Degla and Degla-Beida which are more commercialized than
Frezza whereas the pulp mass proportion in relation to whole fruits is
highest for Frezza (88.28%). Moreover, there is a large variability
concerning the weights and densities of constitutive tissues in each
variety. The white tissue is dominant in Mech-Degla in opposite to
the two other varieties. The variance analyze showed that the
difference in weights between brown and white tissues is significant
(P = 95%) for all studied varieties. Some other morphologic and
chemical proprieties of the whole pulps and their two constitutive
parts (brown or pigmented and white) are also investigated. The
predominance of phenolics in Mech-Degla (4.01g/100g, w.b) and
Frezza (4.96 g/100g, w.b) pulps brown part is the main result
revealed in this study.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: Persea declinata (Bl.) Kosterm is a member of the
Lauraceae family, widely distributed in Southeast Asia. It is from the
same genus with avocado (Persea americana Mill), which is widely
consumed as food and for medicinal purposes. In the present study,
we examined the anticancer properties of Persea declinata (Bl.)
Kosterm bark methanolic crude extract (PDM). PDM exhibited a
potent antiproliferative effect in MCF-7 human breast cancer cells,
with an IC50 value of 16.68 .g/mL after 48h of treatment. We
observed that PDM caused cell cycle arrest and subsequent apoptosis
in MCF-7 cells, as exhibited by increased population at G0/G1 phase,
higher lactate dehydrogenase (LDH) release, and DNA
fragmentation. Mechanistic studies showed that PDM caused
significant elevation in ROS production, leading to perturbation of
mitochondrial membrane potential, cell permeability, and activation
of caspases-3/7. On the other hand, real-time PCR and Western blot
analysis showed that PDM treatment increased the expression of the
proapoptotic molecule, Bax, but decreased the expression of
prosurvival proteins, Bcl-2 and Bcl-xL, in a dose-dependent manner.
These findings imply that PDM could inhibit proliferation in MCF-7
cells via cell cycle arrest and apoptosis induction, indicating its
potential as a therapeutic agent worthy of further development.
Abstract: In this work, we propose the application of Japanese
“Origami” art for a floating function of a small aerial vehicle such as a
hexarotor. A preliminary experiment was conducted using Origami
magic balls mounted under a hexarotor. This magic ball can expand
and shrink using an air pump during free flying. Using this interesting
and functional concept, it promises to reduce the resistance of wind as
well as reduce the energy consumption when the Origami balls are
deflated. This approach can be particularly useful in rescue emergency
situations. Furthermore, there are many unexpected reasons that may
cause the multi-rotor has to land on the surface of water due to
problems with the communication between the aircraft and the ground
station. In addition, a complementary experiment was designed to
prove that the hexarotor can fly maintaining the stability and also,
takes off and lands on the surface of water using air balloons.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: This paper reports the empirical investigation on the
effect of involuntary displacement of indigenous tribes on their sociocultural
and food practices. A descriptive research design using the
quantitative approach was applied and individual of indigenous tribes
as unit of analysis. Through a self-administered survey among two
selected Malaysia indigenous tribes, one hundred fifty questionnaires
were successfully collected. With the application of descriptive and
inferential statistic some useful insights pertaining to the issue
investigated was significantly obtained. Findings revealed that
improvement on the socio-culture, economy and knowledge is
apparent on the indigenous groups’ resulted from displacement
program. Displacement also has a slight impact on indigenous
groups’ food practices. These positive indications provide significant
implications, not only for the indigenous groups themselves, but also
for the responsible authorities.
Abstract: Malathion (ML) is a well known pesticide commonly
used in many agricultural and non-agricultural processes. Its toxicity
has been attributed primarily to the accumulation of acetylcholine
(Ach) at nerve junctions, due to the inhibition of acetylcholinesterase
(AChE). The aim of the current research was to study the protective
effect of the melissa plant extract against reproductive impairment
induced by malathion in 32 male albino rats, and the biological
experiment was divided into four groups (8 in each) that given
malathion (27 mg/kg; 1/50 of the LD50 for an oral dose) and/or
Melissa officinalis (MO) extract (200mg/kg/day) by gavages
technique. The sperm counts, sperm motility, sperm morphology,
FSH, LH, and testosterone levels had been determined in testes
homogenate at the end of the experiment. It is worthy to report that,
rats treated with melissa extract did not show a significant difference
when compared with the control group, while rats given malathion
alone had significantly lower sperm count, sperm motility, and
significantly higher abnormal sperm numbers, than the untreated
control rats as well as having significantly lower serum FSH, LH, and
testosterone levels compared with the control group. Administrations
of melissa extract restore all mentioned histological parameters
towards the control group and the melissa extract had a strong
positive protective effect against malathion toxicity. Results the of
biological parameters were confirmed by the histological
examination of rat testes and indicated that, both control and melissa
groups showing normal seminiferous tubules, while malathion group
testicular tissues had necrosis, edema in the seminiferous tubules and
degeneration of spermatogonial cells lining the seminiferous tubules
with incomplete spermatogenesis. The use of melissa against
malathion improved the histological picture and showing normal
seminiferous tubules with complete spermatogenesis and almost there
was no histopathological changes could be noted.
Abstract: Natural antimicrobials are used to preserve foods that
can be found in plants, animals, and microorganisms. Antimicrobial
substances are natural or artificial agents that produced by
microorganisms or obtained semi/total chemical synthesis are used at
low concentrations to inhibit the growth of other microorganisms.
Food borne pathogens and spoilage microorganisms are inactivated
by the use of antagonistic microorganisms and their metabolites.
Yeasts can produce toxic proteins or glycoproteins (toxins) that cause
inhibition of sensitive bacteria and yeast species. Antimicrobial
substance producing phenotypes belonging different yeast genus
were isolated from different sources. Toxins secreted by many yeast
strains inhibiting the growth of other yeast strains. These strains show
antimicrobial activity, inhibiting the growth of mold and bacteria.
The effect of antimicrobial agents produced by yeasts can be
extremely fast, and therefore may be used in various treatment
procedures. Rapid inhibition of microorganisms is possibly caused by
microbial cell membrane lipopolysaccharide binding and in
activation (neutralization) effect. Antimicrobial agents inhibit the
target cells via different mechanisms of action.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: In Egypt, girls have traditionally been educationally
disadvantaged. This disadvantage, however, has been focused on the
failure to enter school. Increasingly it is recognized that girls who
ever-enroll are at least as likely to complete primary and secondary
education as boys. Still the belief persists that girls, especially those
from poor families, will be disadvantaged in terms of school
expenditures and the transitions to secondary and higher education.
We examine expenditures on tutoring during the final year of
preparatory school, and the transition to specific tracks of secondary
education. Tests during the last year of preparatory largely determine
a student’s educational future. Results show that girls, even girls from
poor families, are not disadvantaged in terms of expenditures,
whether for tutoring, fees or general expenses. Moreover, girls are
more likely than boys to advance to general secondary education, the
track that leads to higher education.
Abstract: In this study, six bacterial isolates of a slightly
thermophilic organism from the Sg. Klah hot spring, Malaysia were
successfully isolated and designated as M7T55D1, M7T55D2,
M7T55D3, M7T53D1, M7T53D2 and M7T53D3 respectively. The
bacterial isolates were screened for their cellulose hydrolytic ability
on Carboxymethlycellulose agar medium. The isolated bacterial
strains were identified morphologically, biochemically and
molecularly with the aid of 16S rDNA sequencing. All of the bacteria
showed their optimum growth at a slightly alkaline pH of 7.5 with a
temperature of 55°C. All strains were Gram-negative, non-spore
forming type, strictly aerobic, catalase-positive and oxidase-positive
with the ability to produce thermostable cellulase. Based on BLASTn
results, bacterial isolates of M7T55D2 and M7T53D1 gave the
highest homology (97%) with similarity to Tepidimonas ignava while
isolates M7T55D1, M7T55D3, M7T53D2 and M7T53D3 showed
their closest homology (97%-98%) with Tepidimonas thermarum.
These cellulolytic thermophiles might have a commercial potential to
produce valuable thermostable cellulase.
Abstract: Disasters are quite experienced in our days. They are
caused by floods, landslides, and building fires that is the main
objective of this study. To cope with these unexpected events,
precautions must be taken to protect human lives. The emphasis on
disposal work focuses on the resolution of the evacuation problem in
case of no-notice disaster. The problem of evacuation is listed as a
dynamic network flow problem. Particularly, we model the
evacuation problem as an earliest arrival flow problem with load
dependent transit time. This problem is classified as NP-Hard. Our
challenge here is to propose a metaheuristic solution for solving the
evacuation problem. We define our objective as the maximization of
evacuees during earliest periods of a time horizon T. The objective
provides the evacuation of persons as soon as possible. We
performed an experimental study on emergency evacuation from the
tunisian children’s hospital. This work prompts us to look for
evacuation plans corresponding to several situations where the
network dynamically changes.
Abstract: Abundant and cheap agricultural waste of oil palm trunk (OPT) juice was used to produce bioethanol. Two strains of Saccharomyces cerevisiae and a strain of Pichia stipitis were used to produce bioethanol from the OPT juice. Fermentation was conducted at previously optimized condition at 30oC and without shaking. The kinetic parameters were estimated and calculated. Monod equation and Hinshelwood model is used to relate the specific growth to the concentration of the limiting substrate and also to simulate bioethanol production rate. Among the three strains, single S. cerevisiae Kyokai no. 7 produce the highest ethanol yield of 0.477 g/l.h within the shortest time (12 h). This yeast also produces more than 20 g/l ethanol concentration within 10 h of fermentation.
Abstract: The powders of Ba(Ce1-xZrx)0.90Y0.1O3-δ (BCZY) with 0.2 ≤ x ≤ 0.6 have been prepared by a modified sol-gel method. Triethylenetetramine (TETA) was employed as chelating agent. Phase formation of calcined powders at 1100oC and sintered pellets at 1400oC of BCZY were examined by an X-ray diffractrometer (XRD). XRD results showed the calcined powder and sintered pellet formed a single perovskite phase over the entire range of x values. As the amount of zirconium substitution (x values) increase, the main peaks are shifted to the higher 2theta values which suggest a complete substitution of zirconium into cerium sites. All the obtained calcined powders and sintered pellets possess cubic structure (Pm-3m) at all x values.