Abstract: This paper reveals the interaction between hydrogen
and surface stress in austenitic stainless steel by X-ray diffraction
stress measurement and thermal desorption analysis before and after
being charged with hydrogen. The surface residual stress was varied
by surface finishing using several disc polishing agents. The obtained
results show that the residual stress near surface had a significant
effect on hydrogen absorption behavior, that is, tensile residual stress
promoted the hydrogen absorption and compressive one did opposite.
Also, hydrogen induced equi-biaxial stress and this stress has a linear
correlation with hydrogen content.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: This paper presents a hybrid fuzzy logic control
strategy for a unicycle trajectory following robot on irregular terrains.
In literature, researchers have presented the design of path tracking
controllers of mobile robots on non-frictional surface. In this work,
the robot is simulated to drive on irregular terrains with contrasting
frictional profiles of peat and rough gravel. A hybrid fuzzy logic
controller is utilised to stabilise and drive the robot precisely with the
predefined trajectory and overcome the frictional impact. The
controller gains and scaling factors were optimised using spiral
dynamics optimisation algorithm to minimise the mean square error
of the linear and angular velocities of the unicycle robot. The robot
was simulated on various frictional surfaces and terrains and the
controller was able to stabilise the robot with a superior performance
that is shown via simulation results.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: This paper evaluates the performance of a multi-lane
four legged modern roundabout operating in Muscat using SIDRA
model. The performance measures include Degree of Saturation
(DOS), average delay, and queue lengths. The geometric and traffic
data were used for model preparation. Gap acceptance parameters,
critical gap and follow up headway, were used for calibration of
SIDRA model. The results from the analysis showed that currently
the roundabout is experiencing delays up to 610 seconds per vehicle
with DOS 1.67 during peak hour. Further, sensitivity analysis for
general and roundabout parameters was performed, amongst lane
width, cruise speed, inscribed diameter, entry radius and entry angle
showed that inscribed diameter is most crucial factor affecting delay
and DOS. Up gradation of roundabout to fully signalized junction
was found as the suitable solution which will serve for future years
with LOS C for design year having DOS of 0.9 with average control
delay of 51.9 seconds per vehicle.
Abstract: Taro Scarab beetles (Papuana uninodis, Coleoptera:
Scarabaeidae) inflict severe damage on important root crops and
plants such as Taro or Cocoyam, yam, sweet potatoes, oil palm and
coffee tea plants across Africa and Asia resulting in economic
hardship and starvation in some nations. Scoliid wasps and
Metarhizium anisopliae fungus - bio-control agents; are shown to be
able to control the population of Scarab beetle adults and larvae using
a newly created simulation model based on non-linear ordinary
differential equations that track the populations of the beetle life
cycle stages: egg, larva, pupa, adult and the population of the scoliid
parasitoid wasps, which attack beetle larvae. In spite of the challenge
driven by the longevity of the scarab beetles, the combined effect of
the larval wasps and the fungal bio-control agent is able to control
and drive down the population of both the adult and the beetle eggs
below the environmental carrying capacity within an interval of 120
days, offering the long term prospect of a stable and eco-friendly
environment; where the population of scarab beetles is: regulated by
parasitoid wasps and beneficial soil saprophytes.
Abstract: Climate warming would increase rainfall by shifting
precipitation falling form from snow to rain, and would accelerate
snow cover disappearing by increasing snowpack. Using temperature
and precipitation data in the temperature-index snowmelt model, we
evaluated variability of snowfall and continuous snow cover duration
(CSCD) during 1944-2010 over Pelso, central Finland. Mann-
Kendall non-parametric test determined that annual precipitation
increased by 2.69 (mm/year, p
Abstract: Climate change would cause mean sea level to rise +1
m by 2100. To prevent coastal floods resulting from the sea level
rising, different flood control structures have been built, with
acceptable protection levels. Gothenburg with the River Göta älv
located on the southwest coast of Sweden is a vulnerable city to the
accelerated rises in mean sea level. We evaluated using a sea barrage
in the River Göta älv to protect Gothenburg during this century. The
highest sea level was estimated to 2.95 m above the current mean sea
level by 2100. To verify flood protection against such high sea levels,
both barriers have to be closed. To prevent high water level in the
River Göta älv reservoir, the barriers would be open when the sea
level is low. The suggested flood control structures would
successfully protect the city from flooding events during this century.
Abstract: Using ETABS software, this study analyzed 23
buildings to evaluate effects of mistakes during construction phase on
buildings structural behavior. For modelling, two different loadings
were assumed: 1) design loading and 2) loading due to the effects of
mistakes in construction phase. Research results determined that
considering traditional construction methods for buildings resulted in
a significant increase in dead loads and consequently intensified the
displacements and base-shears of buildings under seismic loads.
Abstract: The liver is the strongest regenerating organ of the
organism, and even with 2/3 surgically removed, it can regenerate
completely. Hence liver cirrhosis may only develop when the
regenerating system is off.
We present the results of a comparative study of structural and
functional characteristics of rat liver tissue under the conditions of
toxic liver cirrhosis development, induced by carbon tetrachloride,
and its prevention/treatment by natural compounds with antioxidant
and immune stimulating action. Studies were made on Wister rats,
weighing 120~140 g. Grape seeds extracts, separately and in
combination with well-known anticirrhotic drug ursodeoxycholic
acid (Urdoxa), have demonstrated effectiveness in prevention of liver
cirrhosis development and its treatment.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.
Abstract: In this paper, we propose a new packing strategy to
find a free resource for run-time mapping of application tasks to
NoC-based Heterogeneous MPSoC. The proposed strategy minimizes
the task mapping time in addition to placing the communicating tasks
close to each other. To evaluate our approach, a comparative study is
carried out for a platform containing single task supported PEs.
Experiments show that our strategy provides better results when
compared to latest dynamic mapping strategies reported in the
literature.
Abstract: The aim of this study is to determine the effect of age
and physiological status on progesterone and energy metabolism of
Ouled Djellal (O.D) breed ewes. 40 healthy ewes were divided into
two groups, primiparous and multiparous, with 20 ewes in each
group. The body weights (BW) (Kg) were 46.6 ± 4.20 and 59.2 ±
3.02, and consuming less 25 to 30% of their basal energetic
requirements. The values of serum glucose, triglycerides and
cholesterol were lower in pregnant than in non-pregnant ewes. The
high to very high significant differences were found during the 15th
week of pregnancy for glycaemia and triglyceridemia respectively.
Concerning serum progesterone, a very highly significant difference
(p
Abstract: This paper present the experimental work of double
unit tunnel form building (TFB) subjected to in-plane lateral cyclic
loading. A one third scale of 3-storey double unit of TFB is tested
until its strength degradation. Then, the TFB is repaired and
retrofitted using additional shear wall, steel angle and CFRP sheet.
The crack patterns, lateral strength, stiffness, ductility and equivalent
viscous damping (EVD) were analyzed and compared before and
after repair and retrofit. The result indicates that the lateral strength
increases by 22% in pushing and 27% in pulling direction. Moreover,
the stiffness and ductility obtained before and after retrofit increase
tremendously by 87.87% and 39.66%, respectively. Meanwhile, the
energy absorption measured by equivalent viscous damping obtained
after retrofit increase by 12.34% in pulling direction. It can be
concluded that the proposed retrofit method is capable to increase the
lateral strength capacity, stiffness and energy absorption of double
unit TFB.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: Molluca Collision Zone is located at the junction of
the Eurasian, Australian, Pacific and the Philippines plates. Between
the Sangihe arc, west of the collision zone, and to the east of
Halmahera arc is active collision and convex toward the Molluca Sea.
This research will analyze the behavior of earthquake occurrence in
Molluca Collision Zone related to the distributions of an earthquake
in each partition regions, determining the type of distribution of a
occurrence earthquake of partition regions, and the mean occurence
of earthquakes each partition regions, and the correlation between the
partitions region. We calculate number of earthquakes using partition
method and its behavioral using conventional statistical methods. In
this research, we used data of shallow earthquakes type and its
magnitudes ≥4 SR (period 1964-2013). From the results, we can
classify partitioned regions based on the correlation into two classes:
strong and very strong. This classification can be used for early
warning system in disaster management.
Abstract: The cooling channels of injection mould play a crucial
role in determining the productivity of moulding process and the
product quality. It’s not a simple task to design high quality cooling
channels. In this paper, an intelligent cooling channels design system
including automatic layout of cooling channels, interference checking
and assembly of accessories is studied. Automatic layout of cooling
channels using genetic algorithm is analyzed. Through integrating
experience criteria of designing cooling channels, considering the
factors such as the mould temperature and interference checking, the
automatic layout of cooling channels is implemented. The method of
checking interference based on distance constraint algorithm and the
function of automatic and continuous assembly of accessories are
developed and integrated into the system. Case studies demonstrate the
feasibility and practicality of the intelligent design system.
Abstract: FengShui, an old Chinese discipline, dates back to
more than 5000 years, is one of the design principles that aim at
creating habitable and sustainable spaces in harmony with nature by
systematizing data within its own structure. Having emerged from
Chinese mysticism and embodying elements of faith in its principles,
FengShui argues that the positive energy in the environment channels
human behavior and psychology. This argument is supported with the
thesis of quantum physics that ‘everything is made up of energy’ and
gains an important place.
In spaces where living and working take place with several
principles and systematized rules, FengShui promises a happier, more
peaceful and comfortable life by influencing human psychology, acts,
and soul as well as the professional and social life of the individual.
Observing these design properties in houses, workplaces, offices, the
environment, and daily life as a design paradigm is significant. In this
study, how FengShui, a Central Asian culture emanated from Chinese
mysticism, shapes design and how it is used as an element of
sustainable design will be explained.