Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: In this investigation, we have evaluated the effects of
arsenic trioxide on hepatic function in pregnant and lactating Swiss
albino mice and their suckling pups. Experiments were carried out on
female mice given 175 ppm As2O3 in their drinking water from the
14th day of pregnancy until day 14 after delivery. Our results showed
a significant decrease in plasma levels of total protein and albumin,
cholesterol and triglyceride in As2O3 treated mice and their pups. The
hyperbilirubinemia and the increased plasma total alkaline
phosphatase activity suggested the presence of cholestasis.
Transaminase activities as well as lactate deshydrogenase activity in
plasma, known as biomarkers of hepatocellular injury, were elevated
indicating hepatic cells’ damage after treatment with As2O3.
Exposure to arsenic led to an increase of liver thiobarbituric acid
reactive substances level along with a concomitant decrease in the
activities of superoxide dismutase, catalase and glutathione
peroxidase and in glutathione.
Abstract: Although, arsenic trioxide has been the subject of
toxicological research, in vitro cytotoxicity and genotoxicity studies
using relevant cell models and uniform methodology are not well
elucidated. Hence, the aim of the present study was to evaluate the
cytotoxicity and genotoxicity induced by arsenic trioxide in human
keratinocytes (HaCaT) using the MTT [3-(4, 5-dimethylthiazol-2-yl)-
2,5-diphenyltetrazolium bromide] and alkaline single cell gel
electrophoresis (Comet) assays, respectively. Human keratinocytes
were treated with different doses of arsenic trioxide for 4 h prior to
cytogenetic assessment. Data obtained from the MTT assay indicated
that arsenic trioxide significantly reduced the viability of HaCaT cells
in a dose-dependent manner, showing an IC50 value of 34.18 ± 0.6
μM. Data generated from the comet assay also indicated a significant
dose-dependent increase in DNA damage in HaCaT cells associated
with arsenic trioxide exposure. We observed a significant increase in
comet tail length and tail moment, showing an evidence of arsenic
trioxide -induced genotoxic damage in HaCaT cells. This study
confirms that the comet assay is a sensitive and effective method to
detect DNA damage caused by arsenic.
Abstract: Recently, universities are increasingly consuming
energy to support various activities. A large population of staff and
students in Malaysian universities has led to excessive energy
consumption which directly gives an impact to the environment. The
key question then ascended “How well is an energy management
(EM) been practiced in universities without taking the Critical
Success Factors (CSFs) into consideration to ensure the management
of university achieves the goals in reducing energy consumption.
Review on past literature is carried out to establish CSFs for EM best
practices. Thus, this paper highlighted the CSFs which have to be
focused on by management of university to successfully measure the
EM implementation and its performance. At the end of this paper, a
theoretical framework is developed for EM success factors towards
sustainable university.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: This study concerned the dynamic behavior of the
wind turbine rotor. Before all we have studied the loads applied to the
rotor, which allows the knowledge their effect on the fatigue, also
studied the rotor with longitudinal crack in order to determine stress,
strain and displacement. Firstly we compared the first six modes
shapes between cracking and uncracking of HAWT rotor. Secondly
we show show evolution of first six natural frequencies with
longitudinal crack propagation. Finally we conclude that the residual
change in the natural frequencies can be used as in shaft crack
diagnosis predictive maintenance.
Abstract: Physical properties of uranium dinitride (UN2) were
investigated in detail using first principle calculations based on
density functional theory (DFT). To study the strong correlation
effects due to 5f uranium valence electrons, the on-site coulomb
interaction correction U via the Hubbard-like term (DFT+U) was
employed. The UN2 structural, mechanical and thermodynamic
properties were calculated within DFT and Various U of DFT+U
approach.
The Perdew–Burke–Ernzerhof (PBE.5.2) version of the
generalized gradient approximation (GGA) is used to describe the
exchange-correlation with the projector-augmented wave (PAW)
pseudo potentials.
A comparative study shows that results are improved by using the
Hubbard formalism for a certain U value correction like the structural
parameter. For some physical properties the variation versus
Hubbard-U is strong like Young modulus but for others it is weakly
noticeable such as bulk modulus.
We noticed also that from U=7.5 eV, elastic results don’t agree
with the cubic cell because of the C44 values which turn out to be
negative.
Abstract: A collection of thirty cultivars/clones of a red pitaya
was used to investigate flowering response to lighting
supplementation in the winter season of 2013-2014 in southern
Taiwan. The night-breaking treatment was conducted during the
period of 10 Oct. 2013 to 5 Mar. 2014 with 4-continuous hours
(22.00 – 02.00 hrs) of additional lighting daily using incandescent
bulbs (100W). Among cultivars and clones tested, twenty-three
genotypes, most belonging to the red-magenta flesh type, were found
to have positively flowering response to the lighting treatment. The
duration of night-breaking treatment for successful flowering
initiation varied from 33- 48 days. The lighting-sensitive genotypes
bore 1-2 flowering flushes. Floral and fruiting stages took 21-26 and
46-59 days, respectively. Among sixteen fruiting genotypes, the
highest fruit set rates were found in Damao 9, D4, D13, Chaozou
large, Chaozhou 5, Small Nick and F22. Five cultivars and clones
(Orejona, D4, Chaozhou large, Chaozhou 5 and Small Nick) produced
fruits with an average weight of more than 300 g per fruit which were
higher than those of the fruits formed in the summer of 2013. Fruits
produced during off-season containing total soluble solids (TSS)
from 17.5 to 20.7oBrix, which were higher than those produced inseason.
Abstract: Verification and Validation of Simulated Process
Model is the most important phase of the simulator life cycle.
Evaluation of simulated process models based on Verification and
Validation techniques checks the closeness of each component model
(in a simulated network) with the real system/process with respect to
dynamic behaviour under steady state and transient conditions. The
process of Verification and Validation helps in qualifying the process
simulator for the intended purpose whether it is for providing
comprehensive training or design verification. In general, model
verification is carried out by comparison of simulated component
characteristics with the original requirement to ensure that each step
in the model development process completely incorporates all the
design requirements. Validation testing is performed by comparing
the simulated process parameters to the actual plant process
parameters either in standalone mode or integrated mode.
A Full Scope Replica Operator Training Simulator for PFBR -
Prototype Fast Breeder Reactor has been developed at IGCAR,
Kalpakkam, INDIA named KALBR-SIM (Kalpakkam Breeder
Reactor Simulator) where in the main participants are
engineers/experts belonging to Modeling Team, Process Design and
Instrumentation & Control design team. This paper discusses about
the Verification and Validation process in general, the evaluation
procedure adopted for PFBR operator training Simulator, the
methodology followed for verifying the models, the reference
documents and standards used etc. It details out the importance of
internal validation by design experts, subsequent validation by
external agency consisting of experts from various fields, model
improvement by tuning based on expert’s comments, final
qualification of the simulator for the intended purpose and the
difficulties faced while co-coordinating various activities.
Abstract: Malaysia is rich with historic buildings, particularly in
Penang and Malacca states. Restoration activities are increasingly
important as these states are recognized under UNESCO World
Heritage Sites. Restoration activities help to maintain the uniqueness
and value of a heritage building. However, increasing in restoration
activities has resulted in large quantities of waste. To cope with this
problem, the 3R concept (reduce, reuse and recycle) is introduced.
The 3R concept is one of the waste management hierarchies. This
concept is still yet to apply in the building restoration industry
compared to the construction industry. Therefore, this study aims to
promote the 3R concept in the heritage building restoration industry.
This study aims to examine the importance of 3R concept and to
identify challenges in applying the 3R concept in the heritage
building restoration industry. This study focused on contractors and
consultants who are involved in heritage restoration projects in
Penang. Literature review and interviews helps to reach the research
objective. Data that obtained is analyzed by using content analysis.
For the research, application of 3R concept is important to conserve
natural resources and reduce pollution problems. However, limited
space to organise waste is the obstruction during the implementation
of this concept. In conclusion, the 3R concept plays an important role
in promoting environmental conservation and helping in reducing the
construction waste.
Abstract: In the present work, the alloy of Bismuth-lead is
prepared on the basis of percentage of molecular weight 9:1, 5:5 and
1:9 ratios and grown by Zone- Refining Technique under a vacuum
atmosphere. The EDAX of these samples are done and the results are
reported. Micro hardness test has been used as an alternative test for
measuring material’s tensile properties. The effect of temperature and
load on the hardness of the grown alloy has been studied. Further the
comparative studies of work hardening coefficients are reported.
Abstract: Construction cost estimation is one of the most
important aspects of construction project design. For generations, the
process of cost estimating has been manual, time-consuming and
error-prone. This has partly led to most cost estimates to be unclear
and riddled with inaccuracies that at times lead to over- or underestimation
of construction cost. The development of standard set of
measurement rules that are understandable by all those involved in a
construction project, have not totally solved the challenges. Emerging
Building Information Modelling (BIM) technologies can exploit
standard measurement methods to automate cost estimation process
and improve accuracies. This requires standard measurement
methods to be structured in ontological and machine readable format;
so that BIM software packages can easily read them. Most standard
measurement methods are still text-based in textbooks and require
manual editing into tables or Spreadsheet during cost estimation. The
aim of this study is to explore the development of an ontology based
on New Rules of Measurement (NRM) commonly used in the UK for
cost estimation. The methodology adopted is Methontology, one of
the most widely used ontology engineering methodologies. The
challenges in this exploratory study are also reported and
recommendations for future studies proposed.
Abstract: Background: With the perceived pain and poor
function experienced following knee arthroplasty, patients usually
feel un-satisfied. Yet, a controversy still persists on the appropriate
operative technique that doesn’t affect proprioception much.
Purpose: This study compared the effects of Cruciate Retaining
(CR) and Posterior Stabilized (PS) total knee arthroplasty (TKA on
dynamic balance, pain and functional performance following
rehabilitation.
Methods: Thirty patients with CRTKA (group I), thirty with
PSTKA (group II) and fifteen indicated for arthroplasty but weren’t
operated on yet (group III) participated in the study. The mean age
was 54.53±3.44, 55.13±3.48 and 55.33±2.32 years and BMI
35.7±3.03, 35.7±1.99 and 35.73±1.03 kg/m2 for groups I, II and III
respectively. The Berg Balance Scale (BBS), WOMAC pain subscale
and Timed Up-and-Go (TUG) and Stair-Climbing (SC) tests were
used for assessment. Assessments were conducted four weeks preand
post-operatively, three, six and twelve months post-operatively
with the control group being assessed at the same time intervals. The
post-operative rehabilitation involved hospitalization (1st week),
home-based (2nd-4th weeks), and outpatient clinic (5th-12th weeks)
programs, follow-up to all groups for twelve months.
Results: The Mixed design MANOVA revealed that group I had
significantly lower pain scores and SC time compared with group II
three, six and twelve months post-operatively. Moreover, the BBS
scores increased significantly and the pain scores and TUG and SC
time decreased significantly six months post-operatively compared
with four weeks pre- and post-operatively and three months postoperatively
in groups I and II with the opposite being true four weeks
post-operatively. But no significant differences in BBS scores, pain
scores and TUG and SC time between six and twelve months postoperatively
in groups I and II.
Interpretation/Conclusion: CRTKA is preferable to PSTKA,
possibly due to the preserved human proprioceptors in the un-excised
PCL.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: Bacterial strains capable of degradation of malathion
from the domestic sewage were isolated by an enrichment culture
technique. Three bacterial strains were screened and identified as
Acinetobacter baumannii (AFA), Pseudomonas aeruginosa (PS1),
and Pseudomonas mendocina (PS2) based on morphological,
biochemical identification and 16S rRNA sequence analysis.
Acinetobacter baumannii AFA was the most efficient malathion
degrading bacterium, so used for further biodegradation study. AFA
was able to grow in mineral salt medium (MSM) supplemented with
malathion (100 mg/l) as a sole carbon source, and within 14 days,
84% of the initial dose was degraded by the isolate measured by high
performance liquid chromatography. Strain AFA could also degrade
other organophosphorus compounds including diazinon, chlorpyrifos
and fenitrothion. The effect of different culture conditions on the
degradation of malathion like inoculum density, other carbon or
nitrogen sources, temperature and shaking were examined.
Degradation of malathion and bacterial cell growth were accelerated
when culture media were supplemented with yeast extract, glucose
and citrate. The optimum conditions for malathion degradation by
strain AFA were; an inoculum density of 1.5x 10^12CFU/ml at 30°C
with shaking. A specific polymerase chain reaction primers were
designed manually using multiple sequence alignment of the
corresponding carboxylesterase enzymes of Acinetobacter species.
Sequencing result of amplified PCR product and phylogenetic
analysis showed low degree of homology with the other
carboxylesterase enzymes of Acinetobacter strains, so we suggested
that this enzyme is a novel esterase enzyme. Isolated bacterial strains
may have potential role for use in bioremediation of malathion
contaminated.
Abstract: Background and aim: It has not been well studied
whether fentanyl-thiopental (FT) is effective and safe for PSA in
orthopedic procedures in Emergency Department (ED). The aim of
this trial was to evaluate the effectiveness of intravenous FT versus
fentanyl-midazolam (FM) in patients who suffered from shoulder
dislocation or distal radial fracture-dislocation.
Methods: In this randomized double-blinded study, Seventy-six
eligible patients were entered the study and randomly received
intravenous FT or FM. The success rate, onset of action and recovery
time, pain score, physicians’ satisfaction and adverse events were
assessed and recorded by treating emergency physicians. The
statistical analysis was intention to treat.
Results: The success rate after administrating loading dose in FT
group was significantly higher than FM group (71.7% vs. 48.9%,
p=0.04); however, the ultimate unsuccessful rate after 3 doses of
drugs in the FT group was higher than the FM group (3 to 1) but it
did not reach to significant level (p=0.61). Despite near equal onset
of action time in two study group (P=0.464), the recovery period in
patients receiving FT was markedly shorter than FM group
(P
Abstract: Negative pressure phenomenon appears in many
thermodynamic, geophysical and biophysical processes in the Nature
and technological systems. For more than 100 years of the laboratory
researches beginning from F. M. Donny’s tests, the great values of
negative pressure have been achieved. But this phenomenon has not
been practically applied, being only a nice lab toy due to the special
demands for the purity and homogeneity of the liquids for its
appearance. The possibility of creation of direct wave of negative
pressure in real heterogeneous liquid systems was confirmed
experimentally under the certain kinetic and hydraulic conditions.
The negative pressure can be considered as the factor of both useful
and destroying energies. The new approach to generation of the
negative pressure waves in impure, unclean fluids has allowed the
creation of principally new energy saving technologies and
installations to increase the effectiveness and efficiency of different
production processes. It was proved that the negative pressure is one
of the main factors causing hard troubles in some technological and
natural processes. Received results emphasize the necessity to take
into account the role of the negative pressure as an energy factor in
evaluation of many transient thermohydrodynamic processes in the
Nature and production systems.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.