Abstract: In this paper, we propose moving object detection
method which is helpful for driver to safely take his/her car out of
parking lot. When moving objects such as motorbikes, pedestrians,
the other cars and some obstacles are detected at the rear-side of host
vehicle, the proposed algorithm can provide to driver warning. We
assume that the host vehicle is just before departure. Gaussian
Mixture Model (GMM) based background subtraction is basically
applied. Pre-processing such as smoothing and post-processing as
morphological filtering are added. We examine “which color space
has better performance for detection of moving objects?” Three color
spaces including RGB, YCbCr, and Y are applied and compared, in
terms of detection rate. Through simulation, we prove that RGB
space is more suitable for moving object detection based on
background subtraction.
Abstract: It is an established fact that polymers have several
physical limitations such as low stiffness and low resistance to
impact on loading. Hence, polymers do not usually have requisite
mechanical strength for application in various fields. The
reinforcement by high strength fibers provides the polymer
substantially enhanced mechanical properties and makes them more
suitable for a large number of diverse applications. This research
evaluates the effects of particulate Cow bone and Groundnut shell
additions on the mechanical properties and microstructure of cow
bone and groundnut shell reinforced epoxy composite in order to
assess the possibility of using it as a material for engineering
applications. Cow bone and groundnut shell particles reinforced with
epoxy (CBRPC and GSRPC) was prepared by varying the cow bone
and groundnut shell particles from 0-25 wt% with 5 wt% intervals. A
Hybrid of the Cow bone and Groundnut shell (HGSCB) reinforce
with epoxy was also prepared. The mechanical properties of the
developed composites were investigated. Optical microscopy was
used to examine the microstructure of the composites. The results
revealed that mechanical properties did not increase uniformly with
additions in filler but exhibited maximum properties at specific
percentages of filler additions. From the Microscopic evaluation, it
was discovered that homogeneity decreases with increase in % filler,
this could be due to poor interfacial bonding.
Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: HZSM-5 zeolites modified by iron and phosphorus
were applied in catalytic cracking of butene. N2 adsorption and
NH3-TPD were employed to measure the structure and acidity of
catalysts. The results indicate that increasing phosphorus loading
decreased surface area, pore volume and strong acidity of catalysts.
The addition of phosphorus significantly decreased butene conversion
and promoted propylene selectivity. The catalytic performance of
catalyst was strongly dependent on the reaction conditions.
Appropriate reaction conditions could suppress side reactions and
enhance propylene selectivity.
Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: Rice bran is normally used as a raw material for rice
bran oil production or sold as feed with a low price. Conventionally,
the protein in defatted rice bran was extracted using alkaline
extraction and acid precipitation, which involves in chemical usage
and lowering some nutritious component. This study was conducted
in order to extract of rice bran protein concentrate (RBPC) from
defatted rice bran using enzymes and employing polysaccharides in a
precipitating step. The properties of RBPC obtained will be compared
to those of a control sample extracted using a conventional method.
The results showed that extraction of protein from rice bran using
enzymes exhibited the higher protein recovery compared to that
extraction with alkaline. The extraction conditions using alcalase 2%
(v/w) at 50 C, pH 9.5 gave the highest protein (2.44%) and yield
(32.09%) in extracted solution compared to other enzymes. Rice bran
protein concentrate powder prepared by a precipitation step using
alginate (protein in solution: alginate 1:0.016) exhibited the highest
protein (27.55%) and yield (6.84%). Precipitation using alginate was
better than that of acid. RBPC extracted with alkaline (ALK) or
enzyme alcalase (ALC), then precipitated with alginate (AL)
(samples RBP-ALK-AL and RBP-ALC-AL) yielded the precipitation
rate of 75% and 91.30%, respectively. Therefore, protein
precipitation using alginate was then selected. Amino acid profile of
control sample, and sample precipitated with alginate, as compared to
casein and soy protein isolated, showed that control sample showed
the highest content among all sample. Functional property study of
RBP showed that the highest nitrogen solubility occurred in pH 8-10.
There was no statically significant between emulsion capacity and
emulsion stability of control and sample precipitated by alginate.
However, control sample showed a higher of foaming capacity and
foaming stability compared to those of sample precipitated with
alginate. The finding was successful in terms of minimizing
chemicals used in extraction and precipitation steps in preparation of
rice bran protein concentrate. This research involves in a production
of value-added product in which the double amount of protein (28%)
compared to original amount (14%) contained in rice bran could be
beneficial in terms of adding to food products e.g. healthy drink with
high protein and fiber. In addition, the basic knowledge of functional
property of rice bran protein concentrate was obtained, which can be
used to appropriately select the application of this value-added
product from rice bran.
Abstract: Durability of Membrane Electrode Assembly for
Proton Exchange Membrane Fuel Cells was evaluated in both steady
state and accelerated decay modes. Steady state mode was carried out
at constant current of 800mA/cm2 for 2500 hours using air as cathode
feed and pure hydrogen as anode feed. The degradation of the cell
voltage was 0.015V after such 2500 hrs operation. The degradation
rate was therefore calculated to be 6uV/hr. Continuously Vigorous
fluctuation of the cell voltage, which was switched between OCV and
0.2V, was employed for the accelerated decay mode. No obvious
change in performance of the MEA was observed after 10000 cycles
of such operation.
Abstract: Perception, evaluation and representation of the
environment have been the subject of many disciplines including
psychology, geography and architecture. In environmental and social
psychology literature there are several evidences which suggest that
cognitive representations about a place consisted of not only
geographic items but also social and cultural. Mental representations
of residence area or a country are influenced and determined by
social-demographics, the physical and social context. Thus, all
mental representations of a given place are also social
representations. Cognitive maps are the main and common
instruments that are used to identify spatial images and the difference
between physical and subjective environments. The aim of the
current study is investigating the mental and social representations of
Turkey in university students’ minds. Data was collected from 249
university students from different departments (i.e. psychology,
geography, history, tourism departments) of Ege University.
Participants were requested to reflect Turkey in their mind onto the
paper drawing sketch maps. According to the results, cognitive maps
showed geographic aspects of Turkey as well as the context of
symbolic, cultural and political reality of Turkey. That is to say, these
maps had many symbolic and verbal items related to critics on social
and cultural problems, ongoing ethnic and political conflicts, and
actual political agenda of Turkey. Additionally, one of main
differentiations in these representations appeared in terms of the East
and West side of the Turkey, and the representations of the East and
West was varied correspondingly participants’ cultural background,
their ethnic values, and where they have born. The results of the
study were discussed in environmental and social psychological
perspective considering cultural and social values of Turkey and
current political circumstances of the country.
Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: This paper presents the performance of Integrated
Bacterial Foraging Optimization and Particle Swarm Optimization
(IBFO_PSO) technique in MANET routing. The BFO is a bio-inspired
algorithm, which simulates the foraging behavior of bacteria.
It is effectively applied in improving the routing performance in
MANET. In results, it is proved that the PSO integrated with BFO
reduces routing delay, energy consumption and communication
overhead.
Abstract: This paper presents development results of usage of
C-OTDR monitoring systems for rail traffic management. The COTDR
method is based on vibrosensitive properties of optical fibers.
Analysis of Rayleigh backscattering radiation parameters changes
which take place due to microscopic seismoacoustic impacts on the
optical fiber allows to determine seismoacoustic emission source
positions and to identify their types. This approach proved successful
for rail traffic management (moving block system, weigh- in-motion
system etc.).
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: This study, for its research subjects, uses patients who
had undergone total knee replacement surgery from the database of the
National Health Insurance Administration. Through the review of
literatures and the interviews with physicians, important factors are
selected after careful screening. Then using Cross Entropy Method,
Genetic Algorithm Logistic Regression, and Particle Swarm
Optimization, the weight of each factor is calculated and obtained. In
the meantime, Excel VBA and Case Based Reasoning are combined
and adopted to evaluate the system. Results show no significant
difference found through Genetic Algorithm Logistic Regression and
Particle Swarm Optimization with over 97% accuracy in both
methods. Both ROC areas are above 0.87. This study can provide
critical reference to medical personnel as clinical assessment to
effectively enhance medical care quality and efficiency, prevent
unnecessary waste, and provide practical advantages to resource
allocation to medical institutes.
Abstract: Due to today’s globalization as well as outsourcing
practices of the companies, the Supply Chain (SC) performances
have become more dependent on the efficient movement of material
among places that are geographically dispersed, where there is more
chance for disruptions. One such disruption is the quality and
delivery uncertainties of outsourcing. These uncertainties could lead
the products to be unsafe and, as is the case in a number of recent
examples, companies may have to end up in recalling their products.
As a result of these problems, there is a need to develop a
methodology for selecting suppliers globally in view of risks
associated with low quality and late delivery. Accordingly, we
developed a two-stage stochastic model that captures the risks
associated with uncertainty in quality and delivery as well as a
solution procedure for the model. The stochastic model developed
simultaneously optimizes supplier selection and purchase quantities
under price discounts over a time horizon. In particular, our target is
the study of global organizations with multiple sites and multiple
overseas suppliers, where the pricing is offered in suppliers’ local
currencies. Our proposed methodology is applied to a case study for a
US automotive company having two assembly plants and four
potential global suppliers to illustrate how the proposed model works
in practice.
Abstract: Diagnostic enzymes like aspartate aminotransferase
(AST), alanine aminotransferase (ALT) and alkaline phosphatase
(ALP) were determined as indices of heavy metal pollution in Tilapia
guinensis. Three different sets of fishes treated with lead (Pb), iron
(Fe) and copper (Cu) were used for the study while a fourth group
with no heavy metal served as a control. Fishes in each of the groups
were exposed to 2.65mg/l of Pb, 0.85mg/l of Fe and 0.35 mg/l of Cu
in aerated aquaria for 96 hours. Tissue fractionation of the liver
tissues was carried out and the three diagnostic enzymes (AST, ALT,
and ALP) were estimated. Serum levels of the same diagnostic
enzymes were also measured. The mean values of the serum enzyme
activity for ALP in each experimental group were 19.5±1.62,
29.67±2.17 and 1.15±0.27 IU/L for Pb, Fe and Cu groups compared
with 9.99±1.34 IU/L enzyme activity in the control. This result
showed that Pb and Fe caused increased release of the enzyme into
the blood circulation indicating increased tissue damage while Cu
caused a reduction in the serum level as compared with the level in
the control group. The mean values of enzyme activity obtained in
the liver were 102.14±6.12, 140.17±2.06 and 168.23±3.52 IU/L for
Pb, Fe and Cu groups, respectively compared to 91.20±9.42 IU/L
enzyme activity for the control group. The serum and liver AST and
ALT activities obtained in Pb, Fe, Cu and control groups are
reported. It was generally noted that the presence of the heavy metal
caused liver tissues damage and consequent increased level of the
diagnostic enzymes in the serum.
Abstract: Rapid Prototyping (RP) technologies enable physical
parts to be produced from various materials without depending on the
conventional tooling. Fused Deposition Modeling (FDM) is one of
the famous RP processes used at present. Tensile strength and
compressive strength resistance will be identified for different sample
structures and different layer orientations of ABS rapid prototype
solid models. The samples will be fabricated by a FDM rapid
prototyping machine in different layer orientations with variations in
internal geometrical structure. The 0° orientation where layers were
deposited along the length of the samples displayed superior strength
and impact resistance over all the other orientations. The anisotropic
properties were probably caused by weak interlayer bonding and
interlayer porosity.
Abstract: Socio-economic development, which is seen around
the world today, has contributed to the emergence of new problems
of a social nature. Different political, historical, geographical or
economic conditions cause that, in addition to global issues of social
policy such as an aging population, unemployment, migration,
countries, regions, there are also specific new problems that require
diagnosis, individualized approach and efficient, planned solutions.
These should include, among others, digital addiction, peer violence,
obesity among children, the problem of ‘legal highs’, stress,
depression, diseases associated with environmental pollution etc. The
central authorities, selected most often with the tools specific to
representative democracy, that is, the general election, for many
reasons, inter alia, organizational, communication, are not able to
effectively diagnose their intensity, territorial distribution, and thus to
effectively fight them. This article aims to show how in Poland,
citizens influence solving problems related to the broader social
policy implemented at the local government level and indicates the
possibilities of improving those solutions. The conclusions of
theoretical analysis have been supported by empirical studies, which
tested the use of instruments of participatory democracy in the
planning and creation of communal strategies for solving social
problems in one of the Polish voivodeships.