Abstract: This paper concludes that, for economic development,
and to ensure survival, Kenya and similar countries must industrialize
their economy and mechanize their agriculture using modern large
scale methods.
Abstract: This study conducts simulation analyses to find the
optimal debt ceiling of Taiwan, while factoring in welfare
maximization under a dynamic stochastic general equilibrium
framework. The simulation is based on Taiwan's 2001 to 2011
economic data and shows that welfare is maximized at a debt/GDP
ratio of 0.2, increases in the debt/GDP ratio leads to increases in both
tax and interest rates and decreases in the consumption ratio and
working hours. The study results indicate that the optimal debt ceiling
of Taiwan is 20% of GDP, where if the debt/GDP ratio is greater than
40%, the welfare will be negative and result in welfare loss.
Abstract: Residential buildings consume significant amounts of
energy and produce large amount of emissions and waste. However,
there is a substantial potential for energy savings in this sector which
needs to be evaluated over the life cycle of residential buildings. Life
Cycle Assessment (LCA) methodology has been employed to study
the primary energy uses and associated environmental impacts of
different phases (i.e., product, construction, use, end of life, and
beyond building life) for residential buildings. Four different
alternatives of residential buildings in Vancouver (BC, Canada) with
a 50-year lifespan have been evaluated, including High Rise
Apartment (HRA), Low Rise Apartment (LRA), Single family
Attached House (SAH), and Single family Detached House (SDH).
Life cycle performance of the buildings is evaluated for embodied
energy, embodied environmental impacts, operational energy,
operational environmental impacts, total life-cycle energy, and total
life cycle environmental impacts. Estimation of operational energy
and LCA are performed using DesignBuilder software and Athena
Impact estimator software respectively.
The study results revealed that over the life span of the buildings,
the relationship between the energy use and the environmental
impacts are identical. LRA is found to be the best alternative in terms
of embodied energy use and embodied environmental impacts; while,
HRA showed the best life-cycle performance in terms of minimum
energy use and environmental impacts. Sensitivity analysis has also
been carried out to study the influence of building service lifespan
over 50, 75, and 100 years on the relative significance of embodied
energy and total life cycle energy. The life-cycle energy requirements
for SDH are found to be a significant component among the four
types of residential buildings. The overall disclose that the primary
operations of these buildings accounts for 90% of the total life cycle
energy which far outweighs minor differences in embodied effects
between the buildings.
Abstract: A new fast growing trend in tourism is ecotourism, in
which tourists visit natural ecosystems under low impact, nonconsumptive
and locally oriented activities. Through these activities
species and habitats are maintained and typically, underdeveloped
regions are emphasized. Ecotourism provides a great alternative,
especially for rural and undeveloped area. At the same time, despite
its many benefits, it also poses many risks for the naturally protected
areas. If ecotourism is practiced improperly degradation and
irreversible damages could be the unwanted result. In addition, the
lack of MSc programs in the field of Ecotourism in Europe makes it a
necessity to be developed. Such an MSc program is being
implemented with the lead partner the Technical University of
Madrid. The entire partnership has six Universities, seven SMEs and
one National Park from seven different countries all over Europe.
The MSc will have 10 educational modules that will be available
online and will prepare professionals that will be able to implement
ecotourism in a sustainable way. Only through awareness and
education a sustainable ecotourism will be achieved in the protected
areas of Europe.
Abstract: This study aims to evaluate the effective size, section
and structural characteristics of circular hollow steel (CHS) damper.
CHS damper is among steel dampers which are used widely for
seismic energy dissipation because they are easy to install, maintain
and are inexpensive. CHS damper dissipates seismic energy through
metallic deformation due to the geometrical elasticity of circular shape
and fatigue resistance around connection part. After calculating the
effective size, which is found to be height to diameter ratio of √3,
nonlinear FE analyses were carried out to evaluate the structural
characteristics and effective section (diameter-to-ratio).
Abstract: In this paper, improved performance scheme for
joint transmission (JT) is proposed in downlink (DL) coordinated
multi-point (CoMP) in case of the constraint transmission power.
This scheme is that a serving transmission point (TP) requests the
JT to an inter-TP and it selects a precoding technique according
to the channel state information (CSI) from user equipment (UE).
The simulation results show that the bit error rate (BER) and the
throughput performances of the proposed scheme provide the high
spectral efficiency and the reliable data at the cell edge.
Abstract: The conventional Wi-Fi backscatter system can only
process one-to-one communication between the Wi-Fi reader and the
Wi-Fi tag. For improvement of throughput of the conventional system,
this paper proposes the multi-to-multi communication system. In the
proposed system, the interference by the multi-to-multi
communication is effectively cancelled by the orthogonal multiple
access based on the identification code of the tag. Although the
overhead is generated by the procedure for the multi-to-multi
communication, because the procedure is processed by the Wi-Fi
protocol, the overhead is insignificant for the entire communication
procedure. From the numerical results, it is confirmed that the
proposed system has nearly proportional increased throughput in
according to the number of the tag that simultaneously participates in
communication.
Abstract: In this paper, an experiment was conducted to assess
the impact of online deliberation on citizens’ attitudes. Specifically,
this research compared pre and post deliberation opinions of
participants who deliberated online via an asynchronous platform
regarding the issue of political opinion polls. Results indicate that
online deliberation had a positive effect on citizens’ attitudes since it
was found that following deliberation participants changed their
views regarding public opinion polls. Specifically, online deliberation
improved discussants perceptions regarding the reliability of polls,
while suppressing their negative views about the misuse of polls by
media, polling organizations and politicians.
Abstract: Cemented carbides, owing to their excellent
mechanical properties, have been of immense interest in the field of
hard materials for the past few decades. A number of processing
techniques have been developed to obtain high quality carbide tools,
with a wide range of grain size depending on the application and
requirements. Microwave sintering is one of the heating processes,
which has been used to prepare a wide range of materials including
ceramics. A deep understanding of microwave sintering and its
contribution towards control of grain growth and on deformation of
the resulting carbide materials requires further studies and attention.
In addition, the effect of binder materials and their behavior during
microwave sintering is another area that requires clear understanding.
This review aims to focus on microwave sintering, providing
information of how the process works and what type of materials it is
best suited for. In addition, a closer look at some microwave sintered
Tungsten Carbide-Cobalt samples will be taken and discussed,
highlighting some of the key issues and challenges faced in this
research area.
Abstract: The reduction of phosphorus and sulfur in engine oil
are the main topics of this paper. Very reproducible boundary
lubrication tests were conducted as part of Design of Experiment
software (DOE) to study the behavior of fluorinated catalyst iron
fluoride (FeF3), and polutetrafluoroethylene or Teflon (PTFE) in
developing environmentally friendly (reduced P and S) anti-wear
additives for future engine oil formulations. Multi-component
Chevron fully formulated oil (GF3) and Chevron plain oil were used
with the addition of PTFE and catalyst to characterize and analyze
their performance. Lower phosphorus blends were the goal of the
model solution. Experiments indicated that new sub-micron FeF3
catalyst played an important role in preventing breakdown of the
tribofilm.
Abstract: The main objective of this study was to determine the
effects of Nitrogen fixing bacteria and manure application on the seed
yield and yield components in black cumin (Nigella sativa L.). The
experiment was carried out at the RAN Research Station in
Firouzkouh in 2012. A 4×4 factorial experiment, arranged in a
randomized complete blocks designed with three replications.
Nitrogen fixing bacteria at 4 levels (control, Azotobacter,
Azospirillum and Azotobacter + Azospirillum) and manure
application at 4 levels (0, 2.5, 5 and 7.5 ton ha-1) were used at this
investigation. The present results have shown that the highest height,
1000 seeds weight, seed number per follicle, follicle yield, seed yield
and harvest index were obtained after using Azotobacter and
Azospirillum, simultaneously. Manure application only effects on
follicle yield and by 5ton manure ha-1 the highest follicle yield
obtained. Results of this investigation showed that the maximum seed
yield obtained when Aotobacter+Azospirillum inoculated with black
cumin seeds and 5 ton manure ha-1 applied. According to the results
of this investigation the integrated management of Azotobacter and
Azospirillum with manure application is the best treatment for
achieving the maximum quantitative charactersitics of Black cumin.
Abstract: In this study, one dimensional phase change problem
(a Stefan problem) is considered and a numerical solution of this
problem is discussed. First, we use similarity transformation to
convert the governing equations into ordinary differential equations
with its boundary conditions. The solutions of ordinary differential
equation with the associated boundary conditions and interface
condition (Stefan condition) are obtained by using a numerical
approach based on operational matrix of differentiation of shifted
second kind Chebyshev wavelets. The obtained results are compared
with existing exact solution which is sufficiently accurate.
Abstract: There have been rigorous research and development
of unmanned aerial vehicles in the field of search and rescue (SAR)
operation recently. UAVs reduce unnecessary human risks while
assisting rescue efforts through aerial imagery, topographic mapping
and emergency delivery. The application of UAVs in offshore and
nearshore marine SAR missions is discussed in this paper. Projects
that integrate UAV technology into their systems are introduced to
highlight the great advantages and capabilities of UAVs. Scenarios
where UAVs could provide invaluable assistance are also suggested.
Abstract: Effect of sprue/metal head height on mould filling,
microstructure and mechanical properties of TWDI casting is studied.
Results show that metal/sprue height of 50 mm is not sufficient to
push the melt through the gating channel, but as it is increased from
100-350 mm, proper mould filling is achieved. However at higher
heights between 200 mm and 350 mm, defects associated with
incomplete solidification, carbide precipitation and turbulent flow are
evident. This research shows that superior UTS, hardness, nodularity
and nodule count are obtained at 100 mm sprue height.
Abstract: Sampled-data controller is presented for solid oxide
fuel cell systems which is expressed by a sector bounded nonlinear
model. The proposed control law is obtained by solving a convex
problem satisfying several linear matrix inequalities. Simulation
results are given to show the effectiveness of the proposed design
method.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Ant Colony Optimization (ACO) is a promising
modern approach to the unused combinatorial optimization. Here
ACO is applied to finding the shortest during communication link
failure. In this paper, the performances of the prim’s and ACO
algorithm are made. By comparing the time complexity and program
execution time as set of parameters, we demonstrate the pleasant
performance of ACO in finding excellent solution to finding shortest
path during communication link failure.
Abstract: Aging infrastructures became a serious social problem.
This brought out the increased need for the legislation of a new strict
guideline for infrastructure management. Although existing guidelines
provided basics of how to evaluate and manage the condition of
infrastructures, they needed improvements for their evaluation
procedures. Most guidelines mainly focused on the structural
condition of infrastructures and did not properly reflect service aspects
of infrastructures such as performance, public demand, capacity, etc.,
which were significantly valuable to public. Regardless of the
importance, these factors were often neglected in infrastructure
evaluations, because they were quite subjective and difficult to
quantify in rational manner. Thus, this study proposed a framework to
properly identify and evaluate the service indicators. This study
showed that service indicators could be grouped into two categories
and properly evaluated using AHP and Fuzzy. Overall, proposed
framework is expected to assist governmental agency in establishing
effective investment strategies for infrastructure improvements.
Abstract: Food poisoning and infection by bacteria are of public
health significance to both developing and developed countries.
Samples of ogi (akamu) prepared from white and yellow variety of
maize sold in Uturu and Okigwe were analyzed together with the
laboratory prepared ogi for bacterial quality using the standard
microbiological methods. The analyses showed that both white and
yellow variety had total bacterial counts (cfu/g) of 4.0 ×107 and 3.9 x
107 for the laboratory prepared ogi while the commercial ogi had 5.2
x 107 and 4.9 x107, 4.9 x107 and 4.5 x107, 5.4 x107 and 5.0 x107 for
Eke-Okigwe, Up-gate and Nkwo-Achara market respectively. The
Staphylococcal counts ranged from 2.0 x 102 to 5.0 x102 and 1.0 x
102 to 4.0 x102 for the white and yellow variety from the different
markets while Staphylococcal growth was not recorded on the
laboratory prepared ogi. The laboratory prepared ogi had no Coliform
growth while the commercially prepared ogi had counts of 0.5 x103
to 1.6 x 103 for white variety and 0.3 x 103 to 1.1 x103 for yellow
variety respectively. The Lactic acid bacterial count of 3.5x106 and
3.0x106 was recorded for the laboratory ogi while the commercially
prepared ogi ranged from 3.2x106 to 4.2x106 (white variety) and 3.0
x106 to 3.9 x106 (yellow). The presence of bacteria isolates from the
commercial and laboratory fermented ogi showed that Lactobacillus
sp, Leuconostoc sp and Citrobacter sp were present in all the
samples, Micrococcus sp and Klebsiella sp were isolated from Eke-
Okigwe and ABSU-up-gate markets varieties respectively, E. coli
and Staphylococcus sp were present in Eke-Okigwe and Nkwo-
Achara markets while Salmonella sp were isolated from the three
markets. Hence, there are chances of contracting food borne diseases
from commercially prepared ogi. Therefore, there is the need for
sanitary measures in the production of fermented cereals so as to
minimize the rate of food borne pathogens during processing and
storage.