Abstract: In this paper, a prototype PEM fuel cell vehicle
integrated with a 1 kW air-blowing proton exchange membrane fuel
cell (PEMFC) stack as a main power sources has been developed for
a lightweight cruising vehicle. The test vehicle is equipped with a
PEM fuel cell system that provides electric power to a brushed DC
motor. This vehicle was designed to compete with industrial
lightweight vehicle with the target of consuming least amount of
energy and high performance. Individual variations in driving style
have a significant impact on vehicle energy efficiency and it is well
established from the literature. The primary aim of this study was to
assesses the power and fuel consumption of a hydrogen fuel cell
vehicle operating at three difference driving technique (i.e. 25 km/h
constant speed, 22-28 km/h speed range, 20-30 km/h speed range).
The goal is to develop the best driving strategy to maximize
performance and minimize fuel consumption for the vehicle system.
The relationship between power demand and hydrogen consumption
has also been discussed. All the techniques can be evaluated and
compared on broadly similar terms. Automatic intelligent controller
for driving prototype fuel cell vehicle on different obstacle while
maintaining all systems at maximum efficiency was used. The result
showed that 25 km/h constant speed was identified for optimal
driving with less fuel consumption.
Abstract: Online measurement of the product quality is a
challenging task in cement production, especially in the production of
Celitement, a novel environmentally friendly hydraulic binder. The
mineralogy and chemical composition of clinker in ordinary Portland
cement production is measured by X-ray diffraction (XRD) and
X-ray fluorescence (XRF), where only crystalline constituents can be
detected. But only a small part of the Celitement components can be
measured via XRD, because most constituents have an amorphous
structure. This paper describes the development of algorithms
suitable for an on-line monitoring of the final processing step of
Celitement based on NIR-data. For calibration intermediate products
were dried at different temperatures and ground for variable
durations. The products were analyzed using XRD and
thermogravimetric analyses together with NIR-spectroscopy to
investigate the dependency between the drying and the milling
processes on one and the NIR-signal on the other side. As a result,
different characteristic parameters have been defined. A short
overview of the Celitement process and the challenging tasks of the
online measurement and evaluation of the product quality will be
presented. Subsequently, methods for systematic development of
near-infrared calibration models and the determination of the final
calibration model will be introduced. The application of the model on
experimental data illustrates that NIR-spectroscopy allows for a quick
and sufficiently exact determination of crucial process parameters.
Abstract: In this paper, we introduce a flexible box erecting
machine (BEM) that swiftly and automatically transforms cardboard
into a three dimensional box. Recently, the parcel service and
home-shopping industries have grown rapidly, and there is an
increasing need for various box types to ship various products.
However, workers cannot fold thousands of boxes manually in a day.
As such, automatic BEMs are garnering greater attention. This study
takes equipment operation into consideration as well as mechanical
improvements in order to design a BEM that is able to outperform its
conventional counterparts. We analyzed six dispatching rules – First In
First Out (FIFO), Shortest Processing Time (SPT), Earliest Due Date
(EDD), Setup Avoidance, EDD + SPT, and EDD + Setup Avoidance –
to determine which one was most suitable for BEM operation.
Consequently, SPT and Setup Avoidance were found to be the most
critical rules, followed by EDD + Setup Avoidance, EDD + SPT,
EDD, and FIFO. This hierarchy was valid for both our conventional
BEM and our new flexible BEM from the viewpoint of processing
time. We believe that this research can contribute to flexible BEM
management, which has the potential to increase productivity and
convenience.
Abstract: Fresh concrete has one of dynamic properties known
as slump. Slump of concrete is design to compatible with placing
method. Due to hydration reaction of cement, the slump of concrete
is loss through time. Therefore, delayed concrete probably get reject
because slump is unacceptable. In order to recover the slump of
delayed concrete the second dose of superplasticizer (naphthalene
based type F) is added into the system, the slump recovery can be
done as long as the concrete is not setting. By adding superplasticizer
as solution for recover unusable slump loss concrete may affects
other concrete properties. Therefore, this paper was observed setting
times and compressive strength of concrete after being re-dose with
chemical admixture type F (superplasticizer, naphthalene based) for
slump recovery. The concrete used in this study was fly ash concrete
with fly ash replacement of 0%, 30% and 50% respectively. Concrete
mix designed for test specimen was prepared with paste content (ratio
of volume of cement to volume of void in the aggregate) of 1.2 and
1.3, water-to-binder ratio (w/b) range of 0.3 to 0.58, initial dose of
superplasticizer (SP) range from 0.5 to 1.6%. The setting times of
concrete were tested both before and after re-dosed with different
amount of second dose and time of dosing. The research was
concluded that addition of second dose of superplasticizer would
increase both initial and final setting times accordingly to dosage of
addition. As for fly ash concrete, the prolongation effect was higher
as the replacement of fly ash increase. The prolongation effect can
reach up to maximum about 4 hours. In case of compressive strength,
the re-dosed concrete has strength fluctuation within acceptable range
of ±10%.
Abstract: This paper describes the development of new class of
epoxy based rice husk filled jute reinforced composites. Rice husk
flour is added in 0%, 1%, 3%, 5% by weight. Epoxy resin and
triethylenetetramine (T.E.T.A) is used as matrix and hardener
respectively. It investigates the mechanical properties of the
composites and a comparison is done for monolithic jute composite
and the filled ones. The specimens are prepared according to the
ASTM standards and experimentation is carried out using INSTRON
8801. The result shows that with the increase of filler percentage the
tensile properties increases but compressive and flexural properties
decreases.
Abstract: In this work, a framework to model the Supply Chain
(SC) Collaborative Planning (CP) process is proposed. The main
contributions of this framework concern 1) the presentation of the
decision view, the most important one due to the characteristics of the
process, jointly within the physical, organisation and information
views, and 2) the simultaneous consideration of the spatial and
temporal integration among the different supply chain decision
centres. This framework provides the basis for a realistic and
integrated perspective of the supply chain collaborative planning
process and also the analytical modeling of each of its decisional
activities.
Abstract: This study evaluated to facilitate separation of ABS
plastics from other waste plastics by froth flotation after surface
hydrophilization of ABS with heat treatment. The mild heat treatment
at 100oC for 60s could selectively increase the hydrophilicity of the
ABS plastics surface (i.e., ABS contact angle decreased from 79o to
65.8o) among other plastics mixture. The SEM and XPS results of
plastic samples sufficiently supported the increase in hydrophilic
functional groups and decrease contact angle on ABS surface, after
heat treatment. As a result of the froth flotation (at mixing speed 150
rpm and airflow rate 0.3 L/min) after heat treatment, about 85% of
ABS was selectively separated from other heavy plastics with 100%
of purity. The effect of optimum treatment condition and detailed
mechanism onto separation efficiency in the froth floatation was also
investigated. This research is successful in giving a simple, effective,
and inexpensive method for ABS separation from waste plastics.
Abstract: Cadmium oxide (CdO) nanoparticles have been
prepared by chemical coprecipitation method. The synthesized
nanoparticles were characterized by X-ray diffraction analysis
(XRD), scanning electron microscopy (SEM), transmission electron
microscopy (TEM), UV analysis, and dielectric studies. The
crystalline nature and particle size of the CdO nanoparticles were
characterized by Powder X-ray diffraction analysis (XRD). The
morphology of prepared CdO nanoparticles was studied by scanning
electron microscopy. The particle size was studied using the
transmission electron microscopy (TEM).The optical properties were
obtained from UV-Vis absorption spectrum. The dielectric properties
of CdO nanoparticles were studied in the frequency range of 50 Hz–5
MHz at different temperatures. The frequency dependence of the
dielectric constant and dielectric loss is found to decrease with an
increase in the frequency at different temperatures. The ac
conductivity of CdO nanoparticle has been studied.
Abstract: Brushless DC motors (BLDC) are widely used in
industrial areas. The BLDC motors are driven either by indirect ACAC
converters or by direct AC-AC converters. Direct AC-AC
converters i.e. matrix converters are used in this paper to drive the
three phase BLDC motor and it eliminates the bulky DC link energy
storage element. A matrix converter converts the AC power supply to
an AC voltage of variable amplitude and variable frequency. A
control technique is designed to generate the switching pulses for the
three phase matrix converter. For the control of speed of the BLDC
motor a separate PI controller and Fuzzy Logic Controller (FLC) are
designed and a hysteresis current controller is also designed for the
control of motor torque. The control schemes are designed and tested
separately. The simulation results of both the schemes are compared
and contrasted in this paper. The results show that the fuzzy logic
control scheme outperforms the PI control scheme in terms of
dynamic performance of the BLDC motor. Simulation results are
validated with the experimental results.
Abstract: The research investigates the causes of unemployment
in Namibia, Nigeria and South Africa and the role of Capital
Accumulation in reducing the unemployment profile of these
economies as proposed by the post-Keynesian economics. This is
conducted through extensive review of literature on the NAIRU
models and focused on the post-Keynesian view of unemployment
within the NAIRU framework. The NAIRU (non-accelerating
inflation rate of unemployment) model has become a dominant
framework used in macroeconomic analysis of unemployment. The
study views the post-Keynesian economics arguments that capital
accumulation is a major determinant of unemployment.
Unemployment remains the fundamental socio-economic challenge
facing African economies. It has been a burden to citizens of those
economies. Namibia, Nigeria, and South Africa are great African
nations battling with high unemployment rates. The high
unemployment rate in the country led the citizens to chase away
foreigners in the country claiming that they have taken away their
jobs. The study proposes there is a strong relationship between
capital accumulation and unemployment in Namibia, Nigeria, and
South Africa, and capital accumulation is responsible for high
unemployment rates in these countries. For the economies to achieve
steady state level of employment and satisfactory level of economic
growth and development, there is need for capital accumulation to
take place. The countries in the study have been selected after a
critical research and investigations. They are selected based on the
following criteria; African economies with high unemployment rates
above 15% and have about 40% of their workforce unemployed. This
level of unemployment is the critical level of unemployment in
Africa as expressed by International Labour Organization (ILO). And
finally, the African countries experience a slow growth in their Gross
fixed capital formation. Adequate statistical measures have been
employed using a time-series analysis in the study and the results
revealed that capital accumulation is the main driver of
unemployment performance in the chosen African countries. An
increase in the accumulation of capital causes unemployment to
reduce significantly. The results of the research work will be useful
and relevant to federal governments and ministries, departments and
agencies (MDAs) of Namibia, Nigeria and South Africa to resolve
the issue of high and persistent unemployment rates in their
economies which are great burden that slows growth and
development of developing economies. Also, the result can be useful
to World Bank, African Development Bank and International Labour
Organization (ILO) in their further research and studies on how to
tackle unemployment in developing and emerging economies.
Abstract: The question of legal liability over injury arising out
of the import and the introduction of GM food emerges as a crucial
issue confronting to promote GM food and its derivatives. There is a
greater possibility of commercialized GM food from the exporting
country to enter importing country where status of approval shall not
be same. This necessitates the importance of fixing a liability
mechanism to discuss the damage, if any, occurs at the level of
transboundary movement or at the market. There was a widespread consensus to develop the Cartagena
Protocol on Biosafety and to give for a dedicated regime on liability
and redress in the form of Nagoya Kuala Lumpur Supplementary
Protocol on the Liability and Redress (‘N-KL Protocol’) at the
international context. The national legal frameworks based on this
protocol are not adequately established in the prevailing food
legislations of the developing countries. The developing economy
like India is willing to import GM food and its derivatives after the
successful commercialization of Bt Cotton in 2002. As a party to the
N-KL Protocol, it is indispensable for India to formulate a legal
framework and to discuss safety, liability, and regulatory issues
surrounding GM foods in conformity to the provisions of the
Protocol. The liability mechanism is also important in the case where
the risk assessment and risk management is still in implementing
stage. Moreover, the country is facing GM infiltration issues with its
neighbors Bangladesh. As a precautionary approach, there is a need
to formulate rules and procedure of legal liability to discuss any kind
of damage occurs at transboundary trade. In this context, the
proposed work will attempt to analyze the liability regime in the
existing Food Safety and Standards Act, 2006 from the applicability
and domestic compliance and to suggest legal and policy options for
regulatory authorities.
Abstract: The strain intensity and redundant strains, dependent
in multistage TRIP wire drawing processes from values used single
partial reductions, should influence on the intensity of transformation
the retained austenite into martensite and thereby on mechanical
properties of drawn wires. The numerical analysis of drawing
processes with use of Drawing 2D programme, for steel wires made
from TRIP steel with 0,29% has been shown in the work. The change
of strain intensity εc and the values of redundant strain εxy, has been
determined for particular draws in dependence of used single partial
reductions.
Abstract: Average temperatures worldwide are expected to
continue to rise. At the same time, major cities in developing
countries are becoming increasingly populated and polluted.
Governments are tasked with the problem of overheating and air
quality in residential buildings. This paper presents the development
of a model, which is able to estimate the occupant exposure
to extreme temperatures and high air pollution within domestic
buildings. Building physics simulations were performed using the
EnergyPlus building physics software. An accurate metamodel is
then formed by randomly sampling building input parameters and
training on the outputs of EnergyPlus simulations. Metamodels are
used to vastly reduce the amount of computation time required when
performing optimisation and sensitivity analyses. Neural Networks
(NNs) have been compared to a Radial Basis Function (RBF)
algorithm when forming a metamodel. These techniques were
implemented using the PyBrain and scikit-learn python libraries,
respectively. NNs are shown to perform around 15% better than RBFs
when estimating overheating and air pollution metrics modelled by
EnergyPlus.
Abstract: This article discusses the passage of RDB to XML
documents (schema and data) based on metadata and semantic
enrichment, which makes the RDB under flattened shape and is
enriched by the object concept. The integration and exploitation of
the object concept in the XML uses a syntax allowing for the
verification of the conformity of the document XML during the
creation. The information extracted from the RDB is therefore
analyzed and filtered in order to adjust according to the structure of
the XML files and the associated object model. Those implemented
in the XML document through a SQL query are built dynamically. A
prototype was implemented to realize automatic migration, and so
proves the effectiveness of this particular approach.
Abstract: The purposes of this study were to: 1) investigate
operation conditions of SME automotive part industry in Bangkok
and vicinity and 2) to compare operation problem levels of SME
automotive part industry in Bangkok and vicinity according to the
sizes of the enterprises. Samples in this study included 196
entrepreneurs of SME automotive part industry in Bangkok and
vicinity derived from simple random sampling and calculation from
R. V. Krejcie and D. W. Morgan’s tables. Research statistics included
frequency, percentage, mean, standard deviation, and T-test. The
results revealed that in general the problem levels of SME automotive
part industry in Bangkok and vicinity were high. When considering
in details, it was found that the problem levels were high at every
aspect, i.e. personal, production, export, finance, and marketing
respectively. The comparison of the problem levels according to the
sizes of the enterprises revealed statistically significant differences at
.05. When considering on each aspect, it was found that the aspect
with the statistical difference at .05 included 5 aspects, i.e.
production, marketing, finance, personal, and export. The findings
also showed that small enterprises faced more severe problems than
those of medium enterprises.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: A sign pattern is a matrix whose entries belong to the set
{+,−, 0}. An n-by-n sign pattern A is said to allow an eventually
positive matrix if there exist some real matrices A with the same
sign pattern as A and a positive integer k0 such that Ak > 0 for all
k ≥ k0. It is well known that identifying and classifying the n-by-n
sign patterns that allow an eventually positive matrix are posed as two
open problems. In this article, the tree sign patterns of small order
that allow an eventually positive matrix are classified completely.
Abstract: Value addition to agricultural produce is of possible
potential in reducing poverty, improving food security and
malnutrition, therefore the need to develop small and microenterprises
of sweet potato production. A study was carried out in Nigeria to determine the acceptability
of blends sweet potato (Ipomea batatas) and commodities yellow
maize (Zea mays), millet (Pennisetum glaucum), soybean (Glycine
max), bambara groundnut (Vigna subterranean), guinea corn
(Sorghum vulgare), wheat (Triticum aestivum), and roselle (Hibiscus
sabdariffa) through sensory evaluation. Sweet potato (Ipomea batatas) roots were processed using two
methods: oven and sun drying. The blends were also assessed in
terms of functional, chemical and color properties. Most acceptable blends include BAW (80:20 of sweet
potato/wheat), BBC (80:20 of sweet potato/guinea corn), AAB (60:40
of sweet potato/guinea corn), YTE (100% soybean), TYG (100%
sweet potato), KTN (100% wheat flour), XGP (80:20 of sweet
potato/soybean), XAX (60:40 of sweet potato/wheat), LSS (100%
Roselle), CHK (100% Guinea corn), and ABC (60:40% of sweet
potato/ yellow maize). In addition, carried out chemical analysis
revealed that sweet potato has high percentage of vitamins A and C,
potassium (K), manganese (Mn), calcium (Ca), magnesium (Mg) and
iron (Fe) and fibre content. There is also an increase of vitamin A and
Iron in the blended products.
Abstract: The quality of concrete is usually defined by compressive strength, but flexural strength is the most important characteristic of concrete in a pavement which control the mix design of concrete instead of compressive strength. Therefore, the aggregates which are selected for the pavements are affected by higher flexural strength. Roller Compacting Concrete Pavement (RCCP) is not a new construction method. The other characteristic of this method is no bleeding and less shrinkage due to the lower amount of water. For this purpose, a roller is needed for placing and compacting. The surface of RCCP is not smooth; therefore, the most common use of this pavement is in an industrial zone with slower traffic speed which requires durable and tough pavement. For preparing a smoother surface, it can be achieved by asphalt paver. RCCP decrease the finishing cost because there are no bars, formwork, and the lesser labor need for placing the concrete. In this paper, different aspect of RCCP such as mix design, flexural, compressive strength and focus on the different part of RCCP on detail have been investigated.
Abstract: Social networking sites such as Twitter and Facebook
attracts over 500 million users across the world, for those users, their
social life, even their practical life, has become interrelated. Their
interaction with social networking has affected their life forever.
Accordingly, social networking sites have become among the main
channels that are responsible for vast dissemination of different kinds
of information during real time events. This popularity in Social
networking has led to different problems including the possibility of
exposing incorrect information to their users through fake accounts
which results to the spread of malicious content during life events.
This situation can result to a huge damage in the real world to the
society in general including citizens, business entities, and others. In this paper, we present a classification method for detecting the
fake accounts on Twitter. The study determines the minimized set of
the main factors that influence the detection of the fake accounts on
Twitter, and then the determined factors are applied using different
classification techniques. A comparison of the results of these
techniques has been performed and the most accurate algorithm is
selected according to the accuracy of the results. The study has been
compared with different recent researches in the same area; this
comparison has proved the accuracy of the proposed study. We claim
that this study can be continuously applied on Twitter social network
to automatically detect the fake accounts; moreover, the study can be
applied on different social network sites such as Facebook with minor
changes according to the nature of the social network which are
discussed in this paper.