Abstract: In this paper, von Mises and Drucker-Prager yield criteria, as typical ones that consider the effect of intermediate principal stress σ2, have been selected and employed for investigating the influence of σ2 on the solution of a typical stability problem. The bearing capacity factors have been calculated under plane strain condition (strip footing) and axisymmetric condition (circular footing) using the method of stress characteristics together with the criteria mentioned. Different levels of σ2 relative to the other two principal stresses have been considered. While a higher σ2 entry in yield criterion gives a higher bearing capacity; its entry in equilibrium equations (axisymmetric) causes substantial reduction.
Abstract: In this paper, de Laval rotor system has been
characterized by a hinge model and its transient response numerically
treated for a dynamic solution. The effect of the ensuing non-linear
disturbances namely rub and breathing crack is numerically
simulated. Subsequently, three analysis methods: Orbit Analysis, Fast
Fourier Transform (FFT), and Wavelet Transform (WT) are
employed to extract features of the vibration signal of the faulty
system. An analysis of the system response orbits clearly indicates
the perturbations due to the rotor-to-stator contact. The sensitivities
of WT to the variation in system speed have been investigated by
Continuous Wavelet Transform (CWT). The analysis reveals that
features of crack, rubs and unbalance in vibration response can be
useful for condition monitoring. WT reveals its ability to detect nonlinear
signal, and obtained results provide a useful tool method for
detecting machinery faults.
Abstract: Since the advances in digital imaging technologies have led to
development of high quality digital devices, there are a lot of illegal copies
of copyrighted video content on the Internet. Also, unauthorized editing is
occurred frequently. Thus, we propose an editing prevention technique for
high-quality (HQ) video that can prevent these illegally edited copies from
spreading out. The proposed technique is applied spatial and temporal gradient
methods to improve the fidelity and detection performance. Also, the scheme
duplicates the embedding signal temporally to alleviate the signal reduction
caused by geometric and signal-processing distortions. Experimental results
show that the proposed scheme achieves better performance than previously
proposed schemes and it has high fidelity. The proposed scheme can be used
in unauthorized access prevention method of visual communication or traitor
tracking applications which need fast detection process to prevent illegally
edited video content from spreading out.
Abstract: When evaluating the capacity of a generation park to
cover the load in transmission systems, traditional Loss of Load
Expectation (LOLE) and Expected Energy not Served (EENS)
indices can be used. If those indices allow computing the annual
duration and severity of load non covering situations, they do not take
into account the fact that the load excess is generally shifted from one
penury state (hour or quarter of an hour) to the following one. In this
paper, a sequential Monte Carlo framework is introduced in order to
compute adjusted LOLE and EENS indices. Practically, those
adapted indices permit to consider the effect of load excess transfer
on the global adequacy of a generation park, providing thus a more
accurate evaluation of this quantity.
Abstract: This report examines the current state of human gait
simulator development based on the human hip joint model. This unit
will create a database of human gait types, useful for setting up and
calibrating Mechano devices, as well as the creation of new systems
of rehabilitation, exoskeletons and walking robots. The system has
many opportunities to configure the dimensions and stiffness, while
maintaining relative simplicity.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal. There are different sources
of environmental pollution with lead as lead alkyl additives in petrol
and manufacturing processes. The contaminated atmosphere in urban
and industrial areas by lead in Egypt may lead to the contamination
of foods beside the other different sources. The present investigation
studied the risk assessment of lead in some Egyptian edible
vegetables and fruits collected from different environments in Greater
Cairo Governorate, i.e. industrial, heavy traffic and rural areas. A
total of 325 leafy and fruity vegetables and fruits samples belonging
to 11, 6 and 4 different species, respectively were randomly collected
from markets of the three main models. Data indicated the variation
of lead levels in different three areas. The highest levels of lead were
detected in the samples collected from industrial and traffic areas.
However, the lowest levels were found in the rural areas. It could be
concluded that determination of lead levels in foods from different
localities and environments at regularly is very important.
Abstract: This study aims to establish function point process
based on stochastic distribution. In order to demonstrate effectiveness
of the study we present a case study that it applies suggested method
on an automotive electrical and electronics system software
development based on Monte Carlo Simulation. It is expected that the
result of this paper is used as guidance for establishing function point
process in organizations and tools for helping project managers make
decisions correctly.
Abstract: In this paper, a learning algorithm using neuronal networks to improve the roll stability and prevent the rollover in a single unit heavy vehicle is proposed. First, LQR control to keep balanced normalized rollovers, between front and rear axles, below the unity, then a data collected from this controller is used as a training basis of a neuronal regulator. The ANN controller is thereafter applied for the nonlinear side force model, and gives satisfactory results than the LQR one.
Abstract: The study of implicature which is one of the
discussions of pragmatics is such an interesting and challenging topic
to discuss. Implicature is such a meaning which is implied in such an
utterance which is not the same as its literal meaning. The rapid
development of information technology results social networks as
media to broadcast messages. The broadcast messages may be in the
form of jokes which contain implicature. The research applies the
pragmatic equivalent method to analyze the topics of jokes based on
the implicatures contained in them. Furthermore, the method is also
applied to reveal the purpose of creating implicature in jokes. The
findings include the kinds of implicature found in jokes which are
classified into conventional implicature and conversational
implicature. Then, in detailed analysis, implicature in jokes is divided
into implicature related to gender, culture, and social phenomena.
Furthermore, implicature in jokes may not only be used to give
entertainment but also to soften criticisms or satire so that it does not
sound rude and harsh.
Abstract: This paper presents the development of a mobile
application for students at the Faculty of Information Technology,
Rangsit University (RSU), Thailand. RSU upgrades an enrollment
process by improving its information systems. Students can
download the RSU APP easily in order to access the RSU substantial
information. The reason of having a mobile application is to help
students to access the system regardless of time and place. The objectives of this paper include: 1. To develop an application
on iOS platform for those students at the Faculty of Information
Technology, Rangsit University, Thailand. 2. To obtain the students’
perception towards the new mobile app. The target group is those
from the freshman year till the senior year of the faculty of
Information Technology, Rangsit University. The new mobile application, called as RSU APP, is developed by
the department of Information Technology, Rangsit University. It
contains useful features and various functionalities particularly on
those that can give support to students. The core contents of the app
consist of RSU’s announcement, calendar, events, activities, and ebook.
The mobile app is developed on the iOS platform. The user
satisfaction is analyzed from the interview data from 81 interviewees
as well as a Google application like a Google form which 122
interviewees are involved. The result shows that users are satisfied
with the application as they score it the most satisfaction level at 4.67
SD 0.52. The score for the question if users can learn and use the
application quickly is high which is 4.82 SD 0.71. On the other hand,
the lowest satisfaction rating is in the app’s form, apps lists, with the
satisfaction level as 4.01 SD 0.45.
Abstract: Hydrogen produced by means of polymer electrolyte
membrane electrolyzer (PEME) is one of the most promising
methods due to clean and renewable energy source. In the process,
some energy loss due to mass transfer through a PEM is caused by
diffusion, electro-osmotic drag, and the pressure difference between
the cathode channel and anode channel. In PEME, water molecules
and ionic particles transferred between the electrodes from anode to
cathode, Extensive mixing of the hydrogen and oxygen at anode
channel due to gases cross-over must be avoided. In recent times the
consciousness of safety issue in high pressure PEME where the
oxygen mix with hydrogen at anode channel could create, explosive
conditions have generated a lot of concern. In this paper, the steady
state and simulation analysis of gases crossover in PEME on the
temperature and pressure effect are presented. The simulations have
been analysis in MATLAB based on the well-known Fick’s Law of
molecular diffusion. The simulation results indicated that as
temperature increases, there is a significant decrease in operating
voltage.
Abstract: In order to utilize results from global climate models,
dynamical and statistical downscaling techniques have been
developed. For dynamical downscaling, usually a limited area
numerical model is used, with associated high computational cost.
This research proposes dynamic equation for specific space-time
regional climate downscaling from the Educational Global Climate
Model (EdGCM) for Southeast Asia. The equation is for surface air
temperature. This equation provides downscaling values of surface
air temperature at any specific location and time without running a
regional climate model. In the proposed equations, surface air
temperature is approximated from ground temperature, sensible heat
flux and 2m wind speed. Results from the application of the equation
show that the errors from the proposed equations are less than the
errors for direct interpolation from EdGCM.
Abstract: As one of the convenient and noninvasive sensing
approaches, the automatic limb girth measurement has been applied
to detect intention behind human motion from muscle deformation.
The sensing validity has been elaborated by preliminary researches
but still need more fundamental studies, especially on kinetic
contraction modes. Based on the novel fabric strain sensors, a soft
and smart limb girth measurement system was developed by the
authors’ group, which can measure the limb girth in-motion.
Experiments were carried out on elbow isometric flexion and elbow
isokinetic flexion (biceps’ isokinetic contractions) of 90°/s, 60°/s, and
120°/s for 10 subjects (2 canoeists and 8 ordinary people). After
removal of natural circumferential increments due to elbow position,
the joint torque is found not uniformly sensitive to the limb
circumferential strains, but declining as elbow joint angle rises,
regardless of the angular speed. Moreover, the maximum joint torque
was found as an exponential function of the joint’s angular speed.
This research highly contributes to the application of the automatic
limb girth measuring during kinetic contractions, and it is useful to
predict the contraction level of voluntary skeletal muscles.
Abstract: This study focuses on the stress analysis of Mandibular
Advancement Devices (MADs), which are considered as a standard
treatment of snoring that promoted by American Academy of Sleep
Medicine (AASM). Snoring is the most significant feature of
sleep-disordered breathing (SDB). SDB will lead to serious problems
in human health. Oral appliances are ensured in therapeutic effect and
compliance, especially the MADs. This paper proposes a new MAD
design, and the finite element analysis (FEA) is introduced to precede
the stress simulation for this MAD.
Abstract: A psychological contract is an agreement between the
employer and an employee that covers the parties’ informal and
frequently non-verbalized obligations and expectations towards each
other. The contract is a cognitive pattern-governing employee’s
behaviour in the organization. A gap between employee’s
expectations and the organizational reality may lead to difficult-to-solve
conflicts or cause the employee to modify their behaviour
towards organizational values and goals, if they are willing and ready
to verbalize their expectations. The article discusses psychological contracts in the financial
institutions in Poland. Its theoretical part outlines the types of
psychological contracts in organizations (relational, transactional, and
balanced) and shows the process of their verbalization. The purpose
of the article is to present how the type of the psychological contract
relates to employee’s readiness to verbalize it. The article ends with
conclusions arising from the study.
Abstract: Inspired by the Formula-1 competition, IMechE
(Institute of Mechanical Engineers) and Formula SAE (Society of
Mechanical Engineers) organize annual competitions for University
and College students worldwide to compete with a single-seat racecar
they have designed and built. Design of the chassis or the frame is a
key component of the competition because the weight and stiffness
properties are directly related with the performance of the car and the
safety of the driver. In addition, a reduced weight of the chassis has
direct influence on the design of other components in the car. Among
others, it improves the power to weight ratio and the aerodynamic
performance. As the power output of the engine or the battery
installed in the car is limited to 80 kW, increasing the power to
weight ratio demands reduction of the weight of the chassis, which
represents the major part of the weight of the car. In order to reduce
the weight of the car, ION Racing team from University of
Stavanger, Norway, opted for a monocoque design. To ensure
fulfilment of the competition requirements of the chassis, the
monocoque design should provide sufficient torsional stiffness and
absorb the impact energy in case of possible collision. The study reported in this article is based on the requirements for
Formula Student competition. As part of this study, diverse
mechanical tests were conducted to determine the mechanical
properties and performances of the monocoque design. Upon a
comprehensive theoretical study of the mechanical properties of
sandwich composite materials and the requirements of monocoque
design in the competition rules, diverse tests were conducted
including 3-point bending test, perimeter shear test and test for
absorbed energy. The test panels were homemade and prepared with
equivalent size of the side impact zone of the monocoque, i.e. 275
mm x 500 mm, so that the obtained results from the tests can be
representative. Different layups of the test panels with identical core
material and the same number of layers of carbon fibre were tested
and compared. Influence of the core material thickness was also
studied. Furthermore, analytical calculations and numerical analysis
were conducted to check compliance to the stated rules for Structural
Equivalency with steel grade SAE/AISI 1010. The test results were
also compared with calculated results with respect to bending and
torsional stiffness, energy absorption, buckling, etc. The obtained results demonstrate that the material composition
and strength of the composite material selected for the monocoque
design has equivalent structural properties as a welded frame and thus
comply with the competition requirements. The developed analytical
calculation algorithms and relations will be useful for future
monocoque designs with different lay-ups and compositions.
Abstract: Opportunistic Routing (OR) increases the
transmission reliability and network throughput. Traditional routing
protocols preselects one or more predetermined nodes before
transmission starts and uses a predetermined neighbor to forward a
packet in each hop. The opportunistic routing overcomes the
drawback of unreliable wireless transmission by broadcasting one
transmission can be overheard by manifold neighbors. The first
cooperation-optimal protocol for Multirate OR (COMO) used to
achieve social efficiency and prevent the selfish behavior of the
nodes. The novel link-correlation-aware OR improves the
performance by exploiting the miscellaneous low correlated forward
links. Context aware Adaptive OR (CAOR) uses active suppression
mechanism to reduce packet duplication. The Context-aware OR
(COR) can provide efficient routing in mobile networks. By using
Cooperative Opportunistic Routing in Mobile Ad hoc Networks
(CORMAN), the problem of opportunistic data transfer can be
tackled. While comparing to all the protocols, COMO is the best as it
achieves social efficiency and prevents the selfish behavior of the
nodes.
Abstract: The study is the way to identify the problems that
occur in organizing short course’s lifelong learning in the information
and communication technology (ICT) education which are faced by
the lecturer and staff at the Mara Skill Institute and Industrial
Training Institute in Pahang Malaysia. The important aspects of these
issues are classified to five which are selecting the courses
administrative. Fifty lecturers and staff were selected as a respondent.
The sample is selected by using the non-random sampling method
purpose sampling. The questionnaire is used as a research instrument
and divided into five main parts. All the data that gain from the
questionnaire are analyzed by using the SPSS in term of mean,
standard deviation and percentage. The findings showed, there are the
problems occur in organizing the short course for lifelong learning in
ICT education.
Abstract: Rivers have transient storage or dead zones where
injected pollutants or solutes are entrapped for considerable period of
time, known as residence time, before being released into the main
flowing zones of rivers. In this study, a new empirical expression for
residence time, implementing genetic programming on published
dispersion data, has been derived. The proposed expression uses few
hydraulic and geometric characteristics of rivers which are normally
known to the authorities. When compared with some reported
expressions, based on various statistical indices, it can be concluded
that the proposed expression predicts the residence time of pollutants
in natural rivers more accurately.
Abstract: During the last decades, a number of food crises such
as Bovine Spongiform Encephalopathy (BSE), Mad-Cow disease,
Dioxin in chicken food, Food-and-Mouth Disease (FMD), have
certainly inflected the reliability of the food industry. Consequently,
the trend in applying different scientific methods of risk assessment
in food safety has obtained more attentions in the academic and
practice. However, lack of practical approach considering entire food
supply chain is tangible in the academic literature. In this regard, this
paper aims to apply risk assessment tool (FMEA) with integration of
Human Factor along the entire supply chain of food production and
test the method in a case study of Diary production, and analyze its
results.