Abstract: A magnetic induction based underwater communication
link is evaluated using an analytical model and a custom
Finite-Difference Time-Domain (FDTD) simulation tool. The
analytical model is based on the Sommerfeld integral, and a full-wave
simulation tool evaluates Maxwell’s equations using the FDTD
method in cylindrical coordinates. The analytical model and FDTD
simulation tool are then compared and used to predict the system
performance for various transmitter depths and optimum frequencies
of operation. To this end, the system bandwidth, signal to noise
ratio, and the magnitude of the induced voltage are used to estimate
the expected channel capacity. The models show that in seawater, a
relatively low-power and small coils may be capable of obtaining a
throughput of 40 to 300 kbps, for the case where a transmitter is at
depths of 1 to 3 m and a receiver is at a height of 1 m.
Abstract: In this paper, we present a numerical optical properties of a triangular periodic lattice of elliptical air holes. We report the influence of the ratio (semi-major axis length of elliptical hole to the filling ratio) on the photonic band gap. Then by using the finite difference time domain (FDTD) algorithm, the resonant wavelength of the point defect microcavities in a two-dimensional photonic crystal (PC) shifts towards the low wavelengths with significantly increased filing ratio. It can be noted that the Q factor is gradually changed to higher when the filling ratio increases. It is due to an increase in reflectivity of the PC mirror. Also we theoretically investigate the H1 cavity, where the value of semi-major axis (Rx) of the six holes surrounding the cavity are fixed at 0.5a and the Rx of the two edge air holes are fixed at the optimum value of 0.52a. The highest Q factor of 4.1359 × 106 is achieved at the resonant mode located at λ = 1.4970 µm.
Abstract: Wetting efficiency of microstructures or nanostructures patterned on Si wafers is a real challenge in integrated circuits manufacturing. In fact, bad or non-uniform wetting during wet processes limits chemical reactions and can lead to non-complete etching or cleaning inside the patterns and device defectivity. This issue is more and more important with the transistors size shrinkage and concerns mainly high aspect ratio structures. Deep Trench Isolation (DTI) structures enabling pixels’ isolation in imaging devices are subject to this phenomenon. While low-frequency acoustic reflectometry principle is a well-known method for Non Destructive Test applications, we have recently shown that it is also well suited for nanostructures wetting characterization in a higher frequency range. In this paper, we present a high-frequency acoustic reflectometry characterization of DTI wetting through a confrontation of both experimental and modeling results. The acoustic method proposed is based on the evaluation of the reflection of a longitudinal acoustic wave generated by a 100 µm diameter ZnO piezoelectric transducer sputtered on the silicon wafer backside using MEMS technologies. The transducers have been fabricated to work at 5 GHz corresponding to a wavelength of 1.7 µm in silicon. The DTI studied structures, manufactured on the wafer frontside, are crossing trenches of 200 nm wide and 4 µm deep (aspect ratio of 20) etched into a Si wafer frontside. In that case, the acoustic signal reflection occurs at the bottom and at the top of the DTI enabling its characterization by monitoring the electrical reflection coefficient of the transducer. A Finite Difference Time Domain (FDTD) model has been developed to predict the behavior of the emitted wave. The model shows that the separation of the reflected echoes (top and bottom of the DTI) from different acoustic modes is possible at 5 Ghz. A good correspondence between experimental and theoretical signals is observed. The model enables the identification of the different acoustic modes. The evaluation of DTI wetting is then performed by focusing on the first reflected echo obtained through the reflection at Si bottom interface, where wetting efficiency is crucial. The reflection coefficient is measured with different water / ethanol mixtures (tunable surface tension) deposited on the wafer frontside. Two cases are studied: with and without PFTS hydrophobic treatment. In the untreated surface case, acoustic reflection coefficient values with water show that liquid imbibition is partial. In the treated surface case, the acoustic reflection is total with water (no liquid in DTI). The impalement of the liquid occurs for a specific surface tension but it is still partial for pure ethanol. DTI bottom shape and local pattern collapse of the trenches can explain these incomplete wetting phenomena. This high-frequency acoustic method sensitivity coupled with a FDTD propagative model thus enables the local determination of the wetting state of a liquid on real structures. Partial wetting states for non-hydrophobic surfaces or low surface tension liquids are then detectable with this method.
Abstract: This article discusses the passage of RDB to XML
documents (schema and data) based on metadata and semantic
enrichment, which makes the RDB under flattened shape and is
enriched by the object concept. The integration and exploitation of
the object concept in the XML uses a syntax allowing for the
verification of the conformity of the document XML during the
creation. The information extracted from the RDB is therefore
analyzed and filtered in order to adjust according to the structure of
the XML files and the associated object model. Those implemented
in the XML document through a SQL query are built dynamically. A
prototype was implemented to realize automatic migration, and so
proves the effectiveness of this particular approach.
Abstract: Crosstalk among interconnects and printed-circuit
board (PCB) traces is a major limiting factor of signal quality in highspeed
digital and communication equipments especially when fast
data buses are involved. Such a bus is considered as a planar
multiconductor transmission line. This paper will demonstrate how
the finite difference time domain (FDTD) method provides an exact
solution of the transmission-line equations to analyze the near end
and the far end crosstalk. In addition, this study makes it possible to
analyze the rise time effect on the near and far end voltages of the
victim conductor. The paper also discusses a statistical analysis,
based upon a set of several simulations. Such analysis leads to a
better understanding of the phenomenon and yields useful
information.
Abstract: Long Distance Truck Drivers (LDTDs) have been
found to be a high risk group in the spread of HIV/AIDS globally;
perhaps, due to their high Sexual Risk Behaviours (SRBs).
Interventions for reducing SRBs in trucking population have not been
fully exploited. A quasi-experimental control group pretest-posttest
design was used to assess the efficacy of psycho-education and
behavioural skills training in reducing SRBs among LDTDs. Sixteen
drivers rivers were randomly assigned into either experimental or
control groups using balloting technique. Questionnaire was used as
an instrument for data collection. Repeated measures t-test and
independent t-test were used to test hypotheses. Intervention had
significant effect on the SRBs among LDTDs at post-test (t{7}=
6.01, p
Abstract: This paper investigates the impact of the hand-hold
positions on both antenna performance and the specific absorption
rate (SAR) induced in the user-s head. A cellular handset with
external antenna operating at GSM-900 frequency is modeled and
simulated using a finite difference time-domain (FDTD)-based
platform SEMCAD-X. A specific anthropomorphic mannequin
(SAM) is adopted to simulate the user-s head, whereas a semirealistic
CAD-model of three-tissues is designed to simulate the
user-s hand. The results show that in case of the handset in hand close
to head at different positions; the antenna total efficiency gets
reduced to (14.5% - 5.9%) at cheek-position and to (27.5% to 11.8%)
at tilt-position. The peak averaged SAR1g values in head close to
handset without hand, are 4.67 W/Kg and 2.66 W/Kg at cheek and
tilt-position, respectively. Due to the presence of hand, the SAR1g in
head gets reduced to (3.67-3.31 W/Kg) at cheek-position and to
(1.84-1.64 W/Kg) at tilt-position, depending on the hand-hold
position.
Abstract: This paper predicts the effect of the user-s hand-hold
position on the Total Isotropic Sensitivity (TIS) of GSM900/1800
mobile phone antennas of realistic in-use conditions, where different
semi-realistic mobile phone models, i.e., candy bar and clamshell, as
well as different antenna types, i.e., external and internal, are
simulated using a FDTD-based platform. A semi-realistic hand model
consisting of three tissues and the SAM head are used in simulations.
The results show a considerable impact on TIS of the adopted mobile
phone models owing to the user-s hand presence at different
positions, where a maximum level of TIS is obtained while grasping
the upper part of the mobile phone against head. Maximum TIS
levels are recorded in talk position for mobile phones with external
antenna and maximum differences in TIS levels due to the hand-hold
alteration are recorded for clamshell-type phones.
Abstract: The volume of XML data exchange is explosively
increasing, and the need for efficient mechanisms of XML data
management is vital. Many XML storage models have been proposed
for storing XML DTD-independent documents in relational database
systems. Benchmarking is the best way to highlight pros and cons of
different approaches. In this study, we use a common benchmarking
scheme, known as XMark to compare the most cited and newly
proposed DTD-independent methods in terms of logical reads,
physical I/O, CPU time and duration. We show the effect of Label
Path, extracting values and storing in another table and type of join
needed for each method-s query answering.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: In this paper, an alternating implicit block method for
solving two dimensional scalar wave equation is presented. The
new method consist of two stages for each time step implemented
in alternating directions which are very simple in computation. To
increase the speed of computation, a group of adjacent points is
computed simultaneously. It is shown that the presented method
increase the maximum time step size and more accurate than the
conventional finite difference time domain (FDTD) method and other
existing method of natural ordering.
Abstract: A compact 1x3 power splitter based on Photonic
Crystal Waveguides (PCW) with flexible power splitting ratio is
presented in this paper. Multimode interference coupler (MMI) is
integrated with PCW. The device size reduction compared with the
conventional MMI power splitter is attributed to the large dispersion
of the PCW. Band Solve tool is used to calculate the band structure of
PCW. Finite Difference Time Domain (FDTD) method is adopted to
simulate the relevant structure at 1550nm wavelength. The device is
polarization insensitive and allows the control of output (o/p) powers
within certain percentage points for both polarizations.
Abstract: The volume of XML data exchange is explosively increasing, and the need for efficient mechanisms of XML data management is vital. Many XML storage models have been proposed for storing XML DTD-independent documents in relational database systems. Benchmarking is the best way to highlight pros and cons of different approaches. In this study, we use a common benchmarking scheme, known as XMark to compare the most cited and newly proposed DTD-independent methods in terms of logical reads, physical I/O, CPU time and duration. We show the effect of Label Path, extracting values and storing in another table and type of join needed for each method's query answering.
Abstract: The wide increase and diffusion on telecommunication
technologies have caused a huge spread of electromagnetic sources
in most European Countries. Since the public is continuously being
exposed to electromagnetic radiation the possible health effects have
become the focus of population concerns. As a result, electromagnetic
field monitoring stations which control field strength in commercial
frequency bands are being placed on the flat roof of many buildings.
However there is no guidance on where to place them. This paper
presents an analysis of frequency, polarization and angles of incidence
of a plane wave which impinges on a flat roof security wall and its
dependence on electromagnetic field strength meters placement.
Abstract: In this paper, we have proposed two novel plasmonic demultiplexing structures based on metal-insulator-metal surfaces which, beside their compact size, have a very good transmission spectrum. The impact of the key internal parameters on the transmission spectrum is numerically analyzed by using the twodimensional (2D) finite difference time domain (FDTD) method. The proposed structures could be used to develop ultra-compact photonic wavelength demultiplexing devices for large-scale photonic integration.
Abstract: A novel PDE solver using the multidimensional wave
digital filtering (MDWDF) technique to achieve the solution of a 2D
seismic wave system is presented. In essence, the continuous physical
system served by a linear Kirchhoff circuit is transformed to an
equivalent discrete dynamic system implemented by a MD wave
digital filtering (MDWDF) circuit. This amounts to numerically
approximating the differential equations used to describe elements of a
MD passive electronic circuit by a grid-based difference equations
implemented by the so-called state quantities within the passive
MDWDF circuit. So the digital model can track the wave field on a
dense 3D grid of points. Details about how to transform the continuous
system into a desired discrete passive system are addressed. In
addition, initial and boundary conditions are properly embedded into
the MDWDF circuit in terms of state quantities. Graphic results have
clearly demonstrated some physical effects of seismic wave (P-wave
and S–wave) propagation including radiation, reflection, and
refraction from and across the hard boundaries. Comparison between
the MDWDF technique and the finite difference time domain (FDTD)
approach is also made in terms of the computational efficiency.
Abstract: In this paper we have developed a FDTD simulation
code which can treat wave propagation of a monopole antenna in a
metallic case which covers with PML, and performed a series of three
dimensional FDTD simulations of electromagnetic wave propagation
in this space .We also provide a measurement set up in antenna lab
and fortunately the simulations and measurements show good
agreement. According to simulation and measurement results, we
confirmed that the computer program which had been written in
FORTRAN, works correctly.
Abstract: Photonic Crystal (PhC) based devices are being
increasingly used in multifunctional, compact devices in integrated
optical communication systems. They provide excellent
controllability of light, yet maintaining the small size required for
miniaturization. In this paper, the band gap properties of PhCs and
their typical applications in optical waveguiding are considered.
Novel PhC based applications such as nonlinear switching and
tapers are considered and simulation results are shown using the
accurate time-domain numerical method based on Finite Difference
Time Domain (FDTD) scheme. The suitability of these devices for
novel applications is discussed and evaluated.
Abstract: The finite-difference time-domain (FDTD) method is
one of the most widely used computational methods in
electromagnetic. This paper describes the design of two-dimensional
(2D) FDTD simulation software for transverse magnetic (TM)
polarization using Berenger's split-field perfectly matched layer
(PML) formulation. The software is developed using Matlab
programming language. Numerical examples validate the software.
Abstract: This paper describes a finite-difference time-domainFDTD) method to analyze lightning surge propagation in electric transmission lines. Numerical computation of solving the Telegraphist-s equations is determined and investigated its effectiveness. A source of lightning surge wave on power transmission lines is modeled by using Heidler-s surge model. The
proposed method was tested against medium-voltage power
transmission lines in comparison with the solution obtained by using
lattice diagram. As a result, the calculation showed that the method is one of accurate methods to analyze transient
lightning wave in power transmission lines.