Abstract: Predicting short term wind speed is essential in order
to prevent systems in-action from the effects of strong winds. It also
helps in using wind energy as an alternative source of energy, mainly
for Electrical power generation. Wind speed prediction has
applications in Military and civilian fields for air traffic control,
rocket launch, ship navigation etc. The wind speed in near future
depends on the values of other meteorological variables, such as
atmospheric pressure, moisture content, humidity, rainfall etc. The
values of these parameters are obtained from a nearest weather
station and are used to train various forms of neural networks. The
trained model of neural networks is validated using a similar set of
data. The model is then used to predict the wind speed, using the
same meteorological information. This paper reports an Artificial
Neural Network model for short term wind speed prediction, which
uses back propagation algorithm.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: In this study thermodynamic performance analysis of a
combined organic Rankine cycle and ejector refrigeration cycle is
carried out for use of low-grade heat source in the form of sensible
energy. Special attention is paid to the effects of system parameters
including the turbine inlet temperature and turbine inlet pressure on the
characteristics of the system such as ratios of mass flow rate, net work
production, and refrigeration capacity as well as the coefficient of
performance and exergy efficiency of the system. Results show that
for a given source the coefficient of performance increases with
increasing of the turbine inlet pressure. However, the exergy
efficiency has an optimal condition with respect to the turbine inlet
pressure.
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: Business transformation initiatives are required by
any organization to jump from its normal mode of operation to the
one that is suitable for the change in the environment such as
competitive pressures, regulatory requirements, changes in labor
market, etc., or internal such as changes in strategy/vision, changes in
the capability, change in the management, etc. Recent advances in
information technology in automating the business processes have
the potential to transform an organization to provide it with a
sustained competitive advantage. Process constitutes the skeleton of
a business. Thus, for a business to exist and compete well, it is
essential for the skeleton to be robust and agile. This paper details
“transformation" from a business perspective, methodologies to bring
about an effective transformation, process-based transformation, and
the role of services computing in this. Further, it details the benefits
that could be achieved through services computing.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: This paper presents a new approach for image
segmentation by applying Pillar-Kmeans algorithm. This
segmentation process includes a new mechanism for clustering the
elements of high-resolution images in order to improve precision and
reduce computation time. The system applies K-means clustering to
the image segmentation after optimized by Pillar Algorithm. The
Pillar algorithm considers the pillars- placement which should be
located as far as possible from each other to withstand against the
pressure distribution of a roof, as identical to the number of centroids
amongst the data distribution. This algorithm is able to optimize the
K-means clustering for image segmentation in aspects of precision
and computation time. It designates the initial centroids- positions
by calculating the accumulated distance metric between each data
point and all previous centroids, and then selects data points which
have the maximum distance as new initial centroids. This algorithm
distributes all initial centroids according to the maximum
accumulated distance metric. This paper evaluates the proposed
approach for image segmentation by comparing with K-means and
Gaussian Mixture Model algorithm and involving RGB, HSV, HSL
and CIELAB color spaces. The experimental results clarify the
effectiveness of our approach to improve the segmentation quality in
aspects of precision and computational time.
Abstract: Phase-Contrast MR imaging methods are widely used
for measurement of blood flow velocity components. Also there are
some other tools such as CT and Ultrasound for velocity map
detection in intravascular studies. These data are used in deriving
flow characteristics. Some clinical applications are investigated
which use pressure distribution in diagnosis of intravascular disorders
such as vascular stenosis. In this paper an approach to the problem of
measurement of intravascular pressure field by using velocity field
obtained from flow images is proposed. The method presented in this
paper uses an algorithm to calculate nonlinear equations of Navier-
Stokes, assuming blood as an incompressible and Newtonian fluid.
Flow images usually suffer the lack of spatial resolution. Our
attempt is to consider the effect of spatial resolution on the pressure
distribution estimated from this method. In order to achieve this aim,
velocity map of a numerical phantom is derived at six different
spatial resolutions. To determine the effects of vascular stenoses on
pressure distribution, a stenotic phantom geometry is considered. A
comparison between the pressure distribution obtained from the
phantom and the pressure resulted from the algorithm is presented. In
this regard we also compared the effects of collocated and staggered
computational grids on the pressure distribution resulted from this
algorithm.
Abstract: The paper presents a compressor anti-surge control
system, that results in maximizing compressor throughput with
pressure standard deviation reduction, increased safety margin
between design point and surge limit line and avoiding possible
machine surge. Alternative control strategies are presented.
Abstract: In this study, the powders of Ni and Ti with 50.5 at.%
Ni for 12 h were blended and cold pressed at the different pressures
(50, 75 and100 MPa).The porous product obtained after Ni-Ti
compacts were synthesized by SHS (self-propagating hightemperature
synthesis) in the different preheating temperatures (200,
250 and 300oC) and heating rates (30, 60 and 90oC/min). The effects
of the pressure, preheating temperature and heating rate were
investigated on biocompatibility in vivo. The porosity in the
synthesized products was in the range of 50.7–59.7 vol. %. The
pressure, preheating temperature and heating rate were found to have
an important effect on the biocompatibility in-vivo of the synthesized
products. Max. fibrotic tissue within the porous implant was found in
vivo periods (6 months), in which compacting pressure 100MPa.
Abstract: Enhancement of the performance of a reverse osmosis
(RO) unit through periodic control is studied. The periodic control
manipulates the feed pressure and flow rate of the RO unit. To ensure
the periodic behavior of the inputs, the manipulated variables (MV)
are transformed into the form of sinusoidal functions. In this case, the
amplitude and period of the sinusoidal functions become the
surrogate MV and are thus regulated via nonlinear model predictive
control algorithm. The simulation results indicated that the control
system can generate cyclic inputs necessary to enhance the closedloop
performance in the sense of increasing the permeate production
and lowering the salt concentration. The proposed control system can
attain its objective with arbitrary set point for the controlled outputs.
Successful results were also obtained in the presence of modeling
errors.
Abstract: In this article, the phenomenon of nonlinear
consolidation in saturated and homogeneous clay layer is studied.
Considering time-varied drainage model, the excess pore water
pressure in the layer depth is calculated. The Generalized Differential
Quadrature (GDQ) method is used for the modeling and numerical
analysis. For the purpose of analysis, first the domain of independent
variables (i.e., time and clay layer depth) is discretized by the
Chebyshev-Gauss-Lobatto series and then the nonlinear system of
equations obtained from the GDQ method is solved by means of the
Newton-Raphson approach. The obtained results indicate that the
Generalized Differential Quadrature method, in addition to being
simple to apply, enjoys a very high accuracy in the calculation of
excess pore water pressure.
Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.
Abstract: In the present work flow past circular cylinder and
cylinder with rectangular and triangular wake splitter is studied to
improve aerodynamic parameters. The Comparison of drag
coefficient is tabulated for bare cylinder, cylinder with rectangular
and triangular wake splitters. Flow past circular cylinder and cylinder
with triangular and rectangular wake splitter is performed at
Reynoldsnumber 5, 20, 40, 50,80, 100.An incompressible PISO finite
volume code employing a non-staggered grid arrangement is used, a
second order upwind scheme is used for convective terms. The time
discretization is implicit and a Second order Crank-Nicholson scheme
is employed. Length of wake splitter in both configurations is taken
to be equal to diameter of cylinder. Wake length is found to be less
with rectangular wake splitter when compared to bare cylinder and
cylinder with triangular wake splitter. Coefficient of drag is found to
be less for triangular wake splitter when compared to bare cylinder &
cylinder with rectangular wake splitter.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: Subsurface erosion in river banks and its details, in
spite of its occurrence in various parts of the world has rarely been
paid attention by researchers. In this paper, quantitative concept of
the subsurface bank erosion has been investigated for vertical banks.
Vertical banks were simulated experimentally by considering a sandy
erodible layer overlaid by clayey one under uniformly distributed
constant overhead pressure. Results of the experiments are indicated
that rate of sandy layer erosion is decreased by an increase in
overburden; likewise, substituting 20% of coarse (3.5 mm) sand layer
bed material by fine material (1.4 mm) may lead to a decrease in
erosion rate by one-third. This signifies the importance of the bed
material composition effect on sandy layers erosion due to subsurface
erosion in river banks.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: A four-lobe pressure dam bearing which is
produced by cutting two pressure dams on the upper two lobes and
two relief-tracks on the lower two lobes of an ordinary four-lobe
bearing is found to be more stable than a conventional four-lobe
bearing. In this paper a four-lobe pressure dam bearing supporting
rigid and flexible rotors is analytically investigated to determine its
performance when L/D ratio is varied in the range 0.75 to 1.5. The
static and dynamic characteristics are studied at various L/D ratios.
The results show that the stability of a four-lobe pressure dam
bearing increases with decrease in L/D ratios both for rigid as well as
flexible rotors.