Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: The present work deals with analyses of the effects
of bearing curvature and non-Newtonian characteristics on the load capacity of an exponential rectangular squeeze film bearing using
Bingham fluids as lubricants. Bingham fluids are characterized by an
yield value and hence the formation of a “rigid" core in the region
between the plates is justified. The flow is confined to the region
between the core and the plates. The shape of the core has been
identified through numerical means. Further, numerical solutions for
the pressure distribution and load carrying capacity of the bearing
for various values of Bingham number and curvature parameter have
been obtained. The effects of bearing curvature and non-Newtonian
characteristics of the lubricant on the bearing performances have been
discussed.
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.
Abstract: A zero dimensional model has been used to investigate
the combustion performance of a single cylinder direct injection
diesel engine fueled by biofuels with options like supercharging and
exhaust gas recirculation. The numerical simulation was performed at
constant speed. The indicated pressure, temperature diagrams are
plotted and compared for different fuels. The emissions of soot and
nitrous oxide are computed with phenomenological models. The
experimental work was also carried out with biodiesel (palm stearin
methyl ester) diesel blends, ethanol diesel blends to validate
simulation results with experimental results, and observed that the
present model is successful in predicting the engine performance with
biofuels.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: The presence of cold air with the convergent
topography of the Lut valley over the valley-s sloping terrain can
generate Low Level Jets (LLJ). Moreover, the valley-parallel
pressure gradients and northerly LLJ are produced as a result of the
large-scale processes. In the numerical study the regional MM5
model was run leading to achieve an appropriate dynamical analysis
of flows in the region for summer and winter. The results of this
study show the presence of summer synoptical systems cause the
formation of north-south pressure gradients in the valley which could
be led to the blowing of winds with the velocity more than 14 ms-1
and vulnerable dust and wind storms lasting more than 120 days.
Whereas the presence of cold air masses in the region in winter,
cause the average speed of LLJs decrease. In this time downslope
flows are noticeable in creating the night LLJs.
Abstract: In this study, the contact problem of a layered composite which consists of two materials with different elastic constants and heights resting on two rigid flat supports with sharp edges is considered. The effect of gravity is neglected. While friction between the layers is taken into account, it is assumed that there is no friction between the supports and the layered composite so that only compressive tractions can be transmitted across the interface. The layered composite is subjected to a uniform clamping pressure over a finite portion of its top surface. The problem is reduced to a singular integral equation in which the contact pressure is the unknown function. The singular integral equation is evaluated numerically and the results for various dimensionless quantities are presented in graphical forms.
Abstract: In a bi-fuel diesel engine, the carburetor plays a vital
role in switching from fuel gas to petrol mode operation and viceversa.
The carburetor is the most important part of the fuel system of
a diesel engine. All diesel engines carry variable venturi mixer
carburetors. The basic operation of the carburetor mainly depends on
the restriction barrel called the venturi. When air flows through the
venturi, its speed increases and its pressure decreases. The main
challenge focuses on designing a mixing device which mixes the
supplied gas is the incoming air at an optimum ratio. In order to
surmount the identified problems, the way fuel gas and air flow in
the mixer have to be analyzed. In this case, the Computational Fluid
Dynamics or CFD approach is applied in design of the prototype
mixer. The present work is aimed at further understanding of the air
and fuel flow structure by performing CFD studies using a software
code. In this study for mixing air and gas in the condition that has
been mentioned in continuance, some mixers have been designed.
Then using of computational fluid dynamics, the optimum mixer has
been selected. The results indicated that mixer with 12 holes can
produce a homogenous mixture than those of 8-holes and 6-holes
mixer. Also the result showed that if inlet convergency was smoother
than outlet divergency, the mixture get more homogenous, the reason
of that is in increasing turbulence in outlet divergency.
Abstract: Vapour recompression system has been used to
enhance reduction in energy consumption and improvement in
energy effectiveness of distillation columns. However, the effects of
certain parameters have not been taken into consideration. One of
such parameters is the column heat loss which has either been
assumed to be a certain percent of reboiler heat transfer or negligible.
The purpose of this study was to evaluate the heat loss from an
ethanol-water vapour recompression distillation column with
pressure increase across the compressor (VRCAS) and compare the
results obtained and its effect on some parameters in similar system
(VRCCS) where the column heat loss has been assumed or neglected.
Results show that the heat loss evaluated was higher when compared
with that obtained for the column VRCCS. The results also showed
that increase in heat loss could have significant effect on the total
energy consumption, reboiler heat transfer, the number of trays and
energy effectiveness of the column.
Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.
Abstract: Supercritical carbon dioxide (SC-CO2) was used as a
solvent to extract oil from wheat bran. Extractions were carried out in a
semi-batch process at temperatures ranging from 40 to 60ºC and
pressures ranging from 10 to 30 MPa, with a carbon dioxide (CO2)
flow rate of 26.81 g/min. The oil obtained from wheat bran at different
extraction conditions was quantitatively measured to investigate the
solubility of oil in SC-CO2. The solubility of wheat bran oil was found
to be enhanced in high temperature and pressure. The composition of
fatty acids in wheat bran oil was measured by gas chromatography
(GC). Linoleic, palmitic, oleic and γ-linolenic acid were the major
fatty acids of wheat bran oil. Tocopherol contents in oil were analyzed
by high performance liquid chromatography (HPLC). The highest
amount of phenolics and tocopherols (α and β) were found at
temperature of 60ºC and pressure of 30 MPa.
Abstract: This paper presents the characterization and design of a capacitive pressure sensor with LC-based 0.35 µm CMOS readout circuit. SPICE is employed to evaluate the characteristics of the readout circuit and COMSOL multiphysics structural analysis is used to simulate the behavior of the pressure sensor. The readout circuit converts the capacitance variation of the pressure sensor into the frequency output. Simulation results show that the proposed pressure sensor has output frequency from 2.50 to 2.28 GHz in a pressure range from 0.1 to 2 MPa almost linearly. The sensitivity of the frequency shift with respect to the applied pressure load is 0.11 GHz/MPa.
Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: The research focuses on the effects of polyphenols
extracted from Sambucus nigra fruit, using an experimental arterial
hypertension pattern, as well as their influence on the oxidative
stress. The results reveal the normalization of the reduced glutathion
concentration, as well as a considerable reduction in the
malondialdehide serum concentration by the polyphenolic protection.
The rat blood pressure values were recorded using a CODATM
system, which uses a non-invasive blood pressure measuring method.
All the measured blood pressure components revealed a biostatistically
significant (p
Abstract: In this study, an experimental investigation was carried
out to fix CO2 into the electronic arc furnace (EAF) reducing slag from
stainless steelmaking process under wet grinding. The slag was ground
by the vibrating ball mill with the CO2 and pure water. The reaction
behavior was monitored with constant pressure method, and the
change of CO2 volume in the experimental system with grinding time
was measured. It was found that the CO2 absorption occurred as soon
as the grinding started. The CO2 absorption under wet grinding was
significantly larger than that under dry grinding. Generally, the
amount of CO2 absorption increased as the amount of water, the
amount of slag, the diameter of alumina ball and the initial pressure of
CO2 increased. However, the initial absorption rate was scarcely
influenced by the experimental conditions except for the initial CO2
pressure. According to this research, the CO2 reacted with the CaO
inside the slag to form CaCO3.
Abstract: ORC (Organic Rankine Cycle) has potential of
reducing consumption of fossil fuels and has many favorable
characteristics to exploit low-temperature heat sources. In this work
thermodynamic performance of ORC with regeneration is
comparatively assessed for various working fluids. Special attention is
paid to the effects of system parameters such as the turbine inlet
pressure on the characteristics of the system such as net work
production, heat input, volumetric flow rate per 1 MW of net work and
quality of the working fluid at turbine exit as well as thermal
efficiency. Results show that for a given source the thermal efficiency
generally increases with increasing of the turbine inlet pressure
however has optimal condition for working fluids of low critical
pressure such as iso-pentane or n-pentane.
Abstract: The flow field in a centrifugal fan is highly complex
with flow reversal taking place on the suction side of impeller and
diffuser vanes. Generally performance of the centrifugal fan could be
enhanced by judiciously introducing splitter vanes so as to improve
the diffusion process. An extensive numerical whole field analysis on
the effect of splitter vanes placed in discrete regions of suspected
separation points is possible using CFD. This paper examines the
effect of splitter vanes corresponding to various geometrical
locations on the impeller and diffuser. The analysis shows that the
splitter vanes located near the diffuser exit improves the static
pressure recovery across the diffusing domain to a larger extent. Also
it is found that splitter vanes located at the impeller trailing edge and
diffuser leading edge at the mid-span of the circumferential distance
between the blades show a marginal improvement in the static
pressure recovery across the fan. However, splitters provided near to
the suction side of the impeller trailing edge (25% of the
circumferential gap between the impeller blades towards the suction
side), adversely affect the static pressure recovery of the fan.
Abstract: Modernizing legacy applications is the key issue facing IT managers today because there's enormous pressure on organizations to change the way they run their business to meet the new requirements. The importance of software maintenance and reengineering is forever increasing. Understanding the architecture of existing legacy applications is the most critical issue for maintenance and reengineering. The artifacts recovery can be facilitated with different recovery approaches, methods and tools. The existing methods provide static and dynamic set of techniques for extracting architectural information, but are not suitable for all users in different domains. This paper presents a simple and lightweight pattern extraction technique to extract different artifacts from legacy systems using regular expression pattern specifications with multiple language support. We used our custom-built tool DRT to recover artifacts from existing system at different levels of abstractions. In order to evaluate our approach a case study is conducted.
Abstract: The heterotrophic seedling growth can be defined as a
product of two components: (1) the weight of mobilized seed reserve,
and (2) conversion efficiency of utilized seed reserve to seedling
tissue. The first component can be further divided into (1) initial seed
weight, and (2) the fraction of seed reserve, which is mobilized. The
objective of this study was the identification of the sensitive seedling
growth component(s) in response to drought and salinity stresses.
Two experiments were separately conducted using various salinity
levels (osmotic pressure) of 0, 0.25, 0.50, 0.75, 1, 1.25 and 1.5 MPa
created using NaCl as first experiment and by polyethylene glycol
(drought stress) of 0, 0.2, 0.4, 0.6, 0.8, 1, 1.2 and 1.4 MPa in second
experiment. Seeds of five crops species (Hordeum vulgare, Brassica
napus, Zea mays, Medicago sativa and Medicago scutellata) were
used in each experiment. In both experiments, seedling growth,
fraction of seed reserve utilization and weight of mobilized seed
reserve decreased with increasing drought and salt intensity.
However, drought and salinity stresses had no effect on the
conversion efficiency. It was concluded that the sensitive component
of seedling growth is the weight of mobilized seed reserve.