Abstract: Raman spectroscopy are used to characterize the
chemical changes in normoxic polyhydroxyethylacrylate gel
dosimeter (PHEA) induced by radiation. Irradiations in the low dose
region are performed and the polymerizations of PHEA gels are
monitored by the observing the changes of Raman shift intensity of
the carbon covalent bond of PHEA originated from both monomer
and the cross-linker. The variation in peak intensities with absorbed
dose was observed. As the dose increase, the peak intensities of
covalent bond of carbon in the polymer gels decrease. This point out
that the amount of absorbed dose affect the polymerization of
polymer gels. As the absorbed dose increase, the polymerizations
also increase. Results verify that PHEA gel dosimeters are sensitive
even in lower dose region.
Abstract: Renewable energy sources have gained ultimate urgency due to the need of the preservation of the environment for a sustainable development. Pyrolysis is an ultimate promising process in the recycling and acquisition of precious chemicals from wastes. Here, the co-pyrolysis of hazelnut shell with ultra-high molecular weight polyethylene was carried out catalytically and noncatalytically at 500 and 650 ºC. Potassium dichromate was added in certain amounts to act as a catalyst. The liquid, solid and gas products quantities were determined by gravimetry. As a main result, remarkable increases in gasification were observed by using this catalyst for pure components and their blends especially at 650 ºC. The increase in gas product quantity was compensated mainly with the decreases in the solid products and additionally in some cases liquid products quantities. These observations may stem from mainly the activation of carbon-carbon bonds rather than carbon-hydrogen bonds via potassium dichromate. Also, the catalytic effect of potassium dichromate on HS: PEO and HS: UHMWPE co-pyrolysis was compared.
Abstract: The research investigates the effects of super plasticizer and molarity of sodium hydroxide alkaline solution on the workability, microstructure and compressive strength of self compacting geopolymer concrete (SCGC). SCGC is an improved way of concreting execution that does not require compaction and is made by complete elimination of ordinary Portland cement content. The parameters studied were superplasticizer (SP) dosage and molarity of NaOH solution. SCGC were synthesized from low calcium fly ash, activated by combinations of sodium hydroxide and sodium silicate solutions, and by incorporation of superplasticizer for self compactability. The workability properties such as filling ability, passing ability and resistance to segregation were assessed using slump flow, T-50, V-funnel, L-Box and J-ring test methods. It was found that the essential workability requirements for self compactability according to EFNARC were satisfied. Results showed that the workability and compressive strength improved with the increase in superplasticizer dosage. An increase in strength and a decrease in workability of these concrete samples were observed with the increase in molarity of NaOH solution from 8M to 14M. Improvement of interfacial transition zone (ITZ) and micro structure with the increase of SP and increase of concentration from 8M to 12M were also identified.
Abstract: New nondestructive technique, namely an inverse technique based on vibration tests, to characterize nonlinear mechanical properties of adhesive layers in sandwich composites is developed. An adhesive layer is described as a viscoelastic isotropic material with storage and loss moduli which are both frequency dependent values in wide frequency range. An optimization based on the planning of experiments and response surface technique to minimize the error functional is applied to decrease considerably the computational expenses. The developed identification technique has been tested on aluminum panels and successfully applied to characterize viscoelastic material properties of 3M damping polymer ISD-112 used as a core material in sandwich panels.
Abstract: Before performing polymerase chain reactions (PCR), a feasible primer set is required. Many primer design methods have been proposed for design a feasible primer set. However, the majority of these methods require a relatively long time to obtain an optimal solution since large quantities of template DNA need to be analyzed. Furthermore, the designed primer sets usually do not provide a specific PCR product. In recent years, evolutionary computation has been applied to PCR primer design and yielded promising results. In this paper, a particle swarm optimization (PSO) algorithm is proposed to solve primer design problems associated with providing a specific product for PCR experiments. A test set of the gene CYP1A1, associated with a heightened lung cancer risk was analyzed and the comparison of accuracy and running time with the genetic algorithm (GA) and memetic algorithm (MA) was performed. A comparison of results indicated that the proposed PSO method for primer design finds optimal or near-optimal primer sets and effective PCR products in a relatively short time.
Abstract: In recent years application of natural antimicrobials
instead of conventional ones, due to their hazardous effects on health,
has got serious attentions. On the basis of the results of different
studies, chitosan, a natural bio-degradable and non-toxic
biopolysaccharide derived from chitin, has potential to be used as a
natural antimicrobial. Chitosan has exhibited high antimicrobial
activity against a wide variety of pathogenic and spoilage
microorganisms, including fungi, and Gram-positive and Gramnegative
bacteria. The antimicrobial action is influenced by intrinsic
factors such as the type of chitosan, the degree of chitosan
polymerization and extrinsic factors such as the microbial organism,
the environmental conditions and presence of the other components.
The use of chitosan in food systems should be based on sufficient
knowledge of the complex mechanisms of its antimicrobial mode of
action. In this article we review a number of studies on the
investigation of chitosan antimicrobial properties and application of
them in culture and food mediums.
Abstract: Plastics occupy wide place in the applications of
automotive, electronics and house goods. Especially reinforced
plastics become popular because of their high strength besides their
advantages of low weight and easy manufacturability. In this study,
mechanical and morphological properties of polypropylene (PP) and
high density polyethylene (HDPE) matrix composites reinforced with
surface modified nano titan dioxide (TiO2) particles were
investigated. Surface modification was made by coating the nano
powders with maleic anhydride grafted styrene ethylene butylene
styrene (SEBS-g-MA) and silane, respectively. After surface
modification, PP/TiO2 and HDPE/TiO2 composites were obtained by
using twin screw extruder at titan dioxide loading of 1 wt.%, 3 wt.%
and 5 wt.%. Effects of surface modification were determined by
thermal and morphological analysis. SEBS-g-MA provided bridging
effect between TiO2 particles and polymer matrix while silane was
effective as a dispersant. Depending on that, homogenous structures
without agglomeration were obtained. Mechanical tests were
performed on the injection moldings of the composites for obtaining
the impact strength, tensile strength, stress at break, elongation and
elastic modulus. Reinforced HDPE and PP moldings gave higher
tensile strength and elastic modulus due to the rigid structure of TiO2.
Slight increment was seen in stress at break. Elongation and impact
strength decreased due to the stiffness of the nano titan dioxide.
Abstract: In the following text, we show that by introducing
universal kinetic scheme, the origin of rate retardation and inhibition
period which observed in dithiobenzoate-mediated RAFT
polymerization can be described properly. We develop our model by
utilizing the method of moments, then we apply our model to
different monomer/RAFT agent systems, both homo- and
copolymerization. The modeling results are in an excellent
agreement with experiments and imply the validity of universal
kinetic scheme, not only for dithiobenzoate-mediated systems, but
also for different types of monomer/RAFT agent ones.
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: Zinc borates can be used as multi-functional
synergistic additives with flame retardant additives in polymers. Zinc
borate is white, non-hygroscopic and powder type product. The most
important properties are low solubility in water and high dehydration
temperature. Zinc borates dehydrate above 290°C and anhydrous zinc
borate has thermal resistance about 400°C. Zinc borates can be
synthesized using several methods such as hydrothermal and solidstate
processes. In this study, the solid-state method was applied at
low temperatures of 600oC and 700oC using the starting materials of
ZnO and H3BO3 with several mole ratios. The reaction time was
determined as 4 hours after some preliminary experiments. After the
synthesis, the crystal structure and the morphology of the products
were examined by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). As a result the forms of ZnB4O7,
Zn3(BO3)2, ZnB2O4 were synthesized and obtained along with the
unreacted ZnO.
Abstract: In the present work we investigate both the elastic and
electric properties of a chiral material. We consider a composite
structure made from a polymer matrix and anisotropic inclusions of
GaAs taking into account piezoelectric and dielectric properties of
the composite material. The principal task of the work is the
estimation of the functional properties of the composite material.
Abstract: The hybrid membranes containing inorganic materials in polymer matrix are identified as a remarkable family of proton conducting hybrid electrolytes. In this work, the proton conducting inorganic/organic hybrid membranes for proton exchange membrane fuel cells (PEMFCs) were prepared using polyvinyl alcohol (PVA), tetraethoxyorthosilane (TEOS) and heteropolyacid (HPA). The synthesized hybrid membranes were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction spectroscopy (XRD), Scanning electron microscopy (SEM) and Thermogravimetry analysis (TGA). The effects of heteropolyacid incorporation on membrane properties, including morphology and thermal stability were extensively investigated.
Abstract: Electrospinning is a broadly used technology to obtain
polymeric nanofibers ranging from several micrometers down to
several hundred nanometers for a wide range of applications. It offers
unique capabilities to produce nanofibers with controllable porous
structure. With smaller pores and higher surface area than regular
fibers, electrospun fibers have been successfully applied in various
fields, such as, nanocatalysis, tissue engineering scaffolds, protective
clothing, filtration, biomedical, pharmaceutical, optical electronics,
healthcare, biotechnology, defense and security, and environmental
engineering. In this study, polyurethane nanofibers were obtained
under different electrospinning parameters. Fiber morphology and
diameter distribution were investigated in order to understand them
as a function of process parameters.
Abstract: This paper presents the simulation results of electric field and potential distributions along surface of silicone rubber polymer insulators under clean and various contamination conditions with/without water droplets. Straight sheds insulator having leakage distance 290 mm was used in this study. Two type of contaminants, playwood dust and cement dust, have been studied the effect of contamination on the insulator surface. The objective of this work is to comparison the effect of contamination on potential and electric field distributions along the insulator surface when water droplets exist on the insulator surface. Finite element method (FEM) is adopted for this work. The simulation results show that contaminations have no effect on potential distribution along the insulator surface while electric field distributions are obviously depended on contamination conditions.
Abstract: The effects of chitosan, a biodegradable polymer,
were studied in Grammatophyllum speciosum protocorm-like bodies
(PLBs) in vitro culture. The chitosan concentration of 0, 5, 10, 15,
20, 25, 50 or 100 mg/l were supplemented in half-strength Murashige
and Skoog (1/2 MS) liquid or on agar media containing 2% (w/v)
sucrose. The results showed that liquid medium supplemented with
15 mg/l chitosan showed the highest relative growth rate (7-fold
increase) of PLBs. On 1/2 MS agar medium supplemented with 25
mg/l chitosan gave the highest relative growth rate (4-fold increase).
The relative growth rate of G. speciosum PLBs on agar medium was
significantly lower than that in liquid medium. Moreover, chitosan,
supplemented to agar medium promoted shoot formation but not
rooting. However, supplementation at too high a level, such as 100
mg/l can inhibit growth and kill PLBs.
Abstract: Degradation of polymeric insulation systems of
electrical equipments increases the space charge density and the
concentration of electrical dipoles. By consequence, the maximum
values and the slopes of absorption/resorption (A/R) currents can
change with insulation systems ageing. In this paper, an analysis of
the nature of the A/R currents and the importance of their
components, especially the polarization current and the current given
by the space charge, is presented. The experimental study concerns
the A/R currents measurements of plane samples (made from
CALMICAGLAS tapes), virgin and thermally accelerated aged. The
obtained results show that the ageing process produces an increase of
the values and a decrease of shapes of the A/R currents. Finally, the
possibility of estimating insulations ageing state and lifetime from
A/R currents measurements is discussed.
Abstract: Copolymerization of ethylene with 1-hexene was
carried out using two ansa-fluorenyl titanium derivative complexes.
The substituent effect on the catalytic activity, monomer reactivity
ratio and polymer property was investigated. It was found that the
presence of t-Bu groups on fluorenyl ring exhibited remarkable
catalytic activity and produced polymer with high molecular weight.
However, these catalysts produce polymer with narrow molecular
weight distribution, indicating the characteristic of single-site
metallocene catalyst. Based on 13C NMR, we can observe that
monomer reactivity ratio was affected by catalyst structure. The rH
values of complex 2 were lower than that of complex 1 which might
be result from the higher steric hindrance leading to a reduction of 1-
hexene insertion step.
Abstract: The mechanical properties of blends consisting of
plasticized poly(vinyl butyral) (PVB) and plasticized poly(vinyl
chloride) (PVC) are studied, in order to evaluate the possibility of
using recycled PVB waste derived from windshields. PVC was
plasticized with 38% of diisononyl phthalate (DINP), while PVB was
plasticized with 28% of triethylene glycol, bis(2-ethylhexanoate)
(3GO). The optimal process conditions for the PVB/PVC blend in 1:1
ratio were determined. Entropy was used in order to theoretically
predict the blends miscibility. The PVB content of each blend
composition used was ranging from zero to 100%. Tensile strength
and strain were tested. In addition, a comparison between recycled
and original PVB, used as constituents of the blend, was performed.
Abstract: We propose a new fiber lens structure for large distance
measurement in which a polymer layer is added to a conventional
fiber lens. The proposed fiber lens can adjust the working distance by
properly choosing the refractive index and thickness of the polymer
layer. In our numerical analysis for the fiber lens radius of 120 μm,
the working distance of the proposed fiber lens is about 10 mm
which is about 30 times larger than conventional fiber lens.