Abstract: In parallel with the appearance of new materials, brick masonry had and still has an essential part of the construction market today, with new technical challenges in designing bricks to meet additional requirements. Being used in structural applications, predicting the performance of clay brick masonry allows a significant cost reduction, in terms of practical experimentation. The behavior of masonry walls depends on the behavior of their elementary components, such as bricks, joints, and coatings. Therefore, it is necessary to consider it at different scales (from the scale of the intrinsic material to the real scale of the wall) and then to develop appropriate models, using numerical simulations. The work presented in this paper focuses on the mechanical characterization of the terracotta material at ambient temperature. As a result, the static Young’s modulus obtained from the flexural test shows different values in comparison with the compression test, as well as with the dynamic Young’s modulus obtained from the Impulse excitation of vibration test. Moreover, the Young's modulus varies according to the direction in which samples are extracted, where the values in the extrusion direction diverge from the ones in the orthogonal directions. Based on these results, hollow bricks can be considered as transversely isotropic bimodulus material.
Abstract: Structural failure is caused mainly by damage that
often occurs on structures. Many researchers focus on to obtain very
efficient tools to detect the damage in structures in the early state. In
the past decades, a subject that has received considerable attention in
literature is the damage detection as determined by variations in the
dynamic characteristics or response of structures. The study presents
a new damage identification technique. The technique detects the
damage location for the incomplete structure system using output
data only. The method indicates the damage based on the free
vibration test data by using ‘Two Points Condensation (TPC)
technique’. This method creates a set of matrices by reducing the
structural system to two degrees of freedom systems. The current
stiffness matrices obtain from optimization the equation of motion
using the measured test data. The current stiffness matrices compare
with original (undamaged) stiffness matrices. The large percentage
changes in matrices’ coefficients lead to the location of the damage. TPC technique is applied to the experimental data of a simply
supported steel beam model structure after inducing thickness change
in one element, where two cases consider. The method detects the
damage and determines its location accurately in both cases. In
addition, the results illustrate these changes in stiffness matrix can be
a useful tool for continuous monitoring of structural safety using
ambient vibration data. Furthermore, its efficiency proves that this
technique can be used also for big structures.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: The elastic period has a primary role in the seismic
assessment of buildings. Reliable calculations and/or estimates of the
fundamental frequency of a building and its site are essential during
analysis and design process. Various code formulas based on
empirical data are generally used to estimate the fundamental
frequency of a structure. For existing structures, in addition to code
formulas and available analytical tools such as modal analyses,
various methods of testing including ambient and forced vibration
testing procedures may be used to determine dynamic characteristics.
In this study, the dynamic properties of the 32 buildings located in
the Madinah of Saudi Arabia were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Ambient vibration measurements of buildings have been
analyzed and the fundamental longitudinal and transverse periods for
all tested buildings are presented. The fundamental mode of vibration
has been compared in plots with codes formulae (Saudi Building
Code, EC8, and UBC1997). The results indicate that measured
periods of existing buildings are shorter than that given by most
empirical code formulas. Recommendations are given based on the
common design and construction practice in Madinah city.
Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: In this study, the adhesion of ice to solid substrates
with different surface properties is compared. Clear ice, similar to
atmospheric in-flight icing encounters, is accreted on the different
substrates under controlled conditions. The ice adhesion behavior is
investigated by means of a dynamic vibration testing technique with
an electromagnetic shaker initiating ice de-bonding in the interface
between the substrate and the ice. The results of the experiments
reveal that the affinity for ice accretion is significantly influenced by
the water contact angle of the respective sample.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: New nondestructive technique, namely an inverse technique based on vibration tests, to characterize nonlinear mechanical properties of adhesive layers in sandwich composites is developed. An adhesive layer is described as a viscoelastic isotropic material with storage and loss moduli which are both frequency dependent values in wide frequency range. An optimization based on the planning of experiments and response surface technique to minimize the error functional is applied to decrease considerably the computational expenses. The developed identification technique has been tested on aluminum panels and successfully applied to characterize viscoelastic material properties of 3M damping polymer ISD-112 used as a core material in sandwich panels.