Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: Forging parts is used to automobiles; because, they have high strength and it is possible to press them into complicated shape. When itis possible to manufacture hollow forging parts, it leads to reduce weightof the automobiles. But, hollow forging parts are confined to axisymmetrical shape. Hollowforging parts that were pressed to complicated shape are expected. Therefore, we forge a blank that aluminum alloy was inserted in stainless steel. After that, we can providecomplex forging parts that are reduced weight,ifit is possible to be melted the aluminum alloy away by using different of melting points.It is necessary to establish heat forging analysis methodon blank consist of stainless steel and aluminum alloy. Because,this forging is different from conventional forging and this technology is not confirmed. In this study, we compared forging experiment with numerical analysis on the view point of forming load and shape after forming and establish how to set the material temperaturesof two metals and material property of stainless steel on the analysis method. Consequently, temperature difference of stainless steel and aluminum alloy was obtained by experiment. We got material property of stainless steel on forging experimental by compression tests. We had compared numerical analysis that was used the temperature difference of two metals and the material property of stainless steel on forging experimental with forging experiment. Forging analysis method on blankconsist of two metals was established by result of numerical analysis having agreedwith result of forging experiment.
Abstract: Due to the determination of the pollution status of
fresh resources in the Egyptian territorial waters is very important for
public health; this study was carried out to reveal the levels of heavy
metals in the shellfish and their environment and its relation to the
highly developed industrial activities in those areas. A total of 100
shellfish samples from the Rosetta, Edku, El-Maadiya, Abo-Kir and
El-Max coasts [10 crustaceans (shrimp) and 10 mollusks (oysters)]
were randomly collected from each coast. Additionally, 10 samples
from both the water and the sediment were collected from each coast.
Each collected sample was analyzed for cadmium, chromium,
copper, lead and zinc residues using a Perkin Elmer atomic
absorption spectrophotometer (AAS). The results showed that the
levels of heavy metals were higher in the water and sediment from
Abo-Kir. The heavy metal levels decreased successively for the
Rosetta, Edku, El-Maadiya, and El-Max coasts, and the
concentrations of heavy metals, except copper and zinc, in shellfish
exhibited the same pattern. For the concentration of heavy metals in
shellfish tissue, the highest was zinc and the concentrations decreased
successively for copper, lead, chromium and cadmium for all coasts,
except the Abo-Kir coast, where the chromium level was highest and
the other metals decreased successively for zinc, copper, lead and
cadmium. In Rosetta, chromium was higher only in the mollusks,
while the level of this metal was lower in the crustaceans; this trend
was observed at the Edku, El-Maadiya and El-Max coasts as well.
Herein, we discuss the importance of such contamination for public
health and the sources of shellfish contamination with heavy metals.
We suggest measures to minimize and prevent these pollutants in the
aquatic environment and, furthermore, how to protect humans from
excessive intake.
Abstract: Laser beam welding for the dissimilar Titanium and
Aluminium thin sheets is an emerging area which is having wider
applications in aerospace, aircraft, automotive, electronics and in
other industries due to its high speed, non-contact, precision with low
heat effects, least welding distortion, low labor costs and convenient
operation. Laser beam welding of dissimilar metal combinations are
increasingly demanded due to high energy densities with small fusion
and heat affected zones. Furthermore, no filler or electrode material is
required and contamination of weld is also very small. The present
study is to reviews the influence of different parameters like laser
power, welding speed, power density, beam diameter, focusing
distance and type of shielding gas on the mechanical properties of
dissimilar metal combinations like SS/Al, Cu/Al and Ti/Al focusing
on aluminum to other materials. Research findings reveal that Ti/Al
combination gives better metallurgical and mechanical properties
than other combinations such as SS/Al and Cu/Al.
Abstract: In recent decades with the development of technology
and lack of food sources, sewage sludge in production of human
foods is inevitable. Various sources of municipal and industrial
sewage sludge that is produced can provide the requirement of plant
nutrients. Soils in arid, semi-arid climate of central Iran that most
affected by water drainage, iron and zinc deficiencies, using of
sewage sludge is helpful. Therefore, the aim of this study is
investigation of sewage sludge and manure application on Ni, Pb and
Cd uptake by Savory. An experiment in a randomized complete block
design with three replications was performed. Sewage sludge
treatments consisted of four levels, control, 15, 30, 80 tons per
hectares; the manure was used in four levels of control, 20, 40 and 80
tons per hectare. Results showed that the wet and dry weights was not
affected by sewage sludge using, while, manure has significant effect
on them. The effect of sewage sludge on the cadmium and lead
concentrations were significant. Interactions of sewage sludge and
manure on dry weight values were not significant. Compare mean
analysis showed that increasing the amount of sewage sludge had no
significant effect on cadmium concentration and it reduced when
sewage sludge usage increased. This is probably due to increased
plant growth and reduced concentrations of these elements in the
plant.
Abstract: In this paper, snow samples containing dust particles
from several sampling points around the city of Ostrava were
analyzed. The pH values of sampled snow were measured and solid
particles analyzed. Particle size, zeta potential and content of selected
heavy metals were determined in solid particles. The pH values of
most samples lay in the slightly acid region. Mean values of particle
size ranged from 290.5 to 620.5 nm. Zeta potential values varied
between -5 and -26.5 mV. The following heavy metal concentration
ranges were found: copper 0.08-0.75 mg/g, lead 0.05-0.9 mg/g,
manganese 0.45-5.9 mg/g and iron 25.7-280.46 mg/g. The highest
values of copper and lead were found in the vicinity of busy
crossroads, and on the contrary, the highest levels of manganese and
iron were detected close to a large steelworks. The proportion
between pH values, zeta potentials, particle sizes and heavy metal
contents was established. Zeta potential decreased with rising pH
values and, simultaneously, heavy metal content in solid particles
increased. At the same time, higher metal content corresponded to
lower particle size.
Abstract: Due to reduced stiffness, research on second
generation titanium alloys for implant applications, like the
metastable β-titanium alloy Ti-15Mo, become more and more
important in the recent years. The machinability of these alloys is
generally poor leading to problems during implant production and
comparably large production costs. Therefore, in the present study,
Ti-15Mo was alloyed with 0.8 wt.-% of the rare earth metals
lanthanum (Ti-15Mo+0.8La) and neodymium (Ti-15Mo+0.8Nd) to
improve its machinability. Their microstructure consisted of a
titanium matrix and micrometer-size particles of the rare earth metals
and two of their oxides. The particles stabilized the microstructure as
grain growth was minimized. As especially the ductility might be
affected by the precipitates, the behavior of Ti-15Mo+0.8La and Ti-
15Mo+0.8Nd was investigated during static and dynamic
deformation at elevated temperature to develop a processing route.
The resulting mechanical properties (static strength and ductility)
were similar in all investigated alloys.
Abstract: Heavy metals are one of the major groups of
contaminants in the environment and many of them are toxic even at
very low concentration in plants and animals. However, some metals
play important roles in the biological function of many enzymes in
living organisms. Metals such as zinc, iron, and cooper are important
for survival and activity of enzymes in plants, however heavy metals
can inhibit enzyme which is responsible for defense system of plants.
Polyphenol oxidase (PPO) is a copper-containing metalloenzyme
which is responsible for enzymatic browning reaction of plants.
Enzymatic browning is a major problem for the handling of
vegetables and fruits in food industry. It can be increased and
effected with many different futures such as metals in the nature and
ground. In the present work, PPO was isolated and characterized
from green leaves of red poppy plant (Papaverr hoeas). Then, the
effect of some known antibrowning agents which can form
complexes with metals and metals were investigated on the red poppy
PPO activity. The results showed that glutathione was the most
potent inhibitory effect on PPO activity. Cu(II) and Fe(II) metals
increased the enzyme activities however, Sn(II) had the maximum
inhibitory effect and Zn(II) and Pb(II) had no significant effect on the
enzyme activity. In order to reduce the effect of heavy metals, the
effects of metal-antibrowning agent complexes on the PPO activity
were determined. EDTA and metal complexes had no significant
effect on the enzyme. L-ascorbic acid and metal complexes decreased
but L-ascorbic acid-Cu(II)-complex had no effect. Glutathione–metal
complexes had the best inhibitory effect on Red poppy leaf PPO
activity.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: Lead (Pb) poisoning is one of the most common and
preventable environmental health problems. There are different
sources of environmental pollution with lead as lead alkyl additives
in petrol and manufacturing processes. Pb in the atmosphere can be
deposited in urban soils, and may then be re-suspended to re-enter the
atmosphere. This could increase human exposure to Pb and cause
long-term health effects. Thus, monitoring Pb pollution is considered
one of the major tasks in controlling pollution. Scalp hair can be
utilized for the determination of lead (Pb) concentration. It provides a
lasting record of metal intakes of weeks or even months, and for most
metals, their accumulation in hair reflects their accumulation in the
whole body. This work was conducted to investigate the
concentration of lead in male scalp hair of Cairo (residential-traffic
and residential-industrial) and rural residents after twenty years of
phasing out of leaded gasoline. Results indicated that the mean
concentration of lead in hair of residential-traffic (9.7552 μg/g ±0.71)
and residential-industrial (12.3288 μg/g ±1.13) was significantly
higher than that in rural residents (4.7327 μg/g ±0.67). The mean
concentration of lead in hair of resident’s industrial areas was the
highest among Cairo residents and not the traffic areas as it was
before phasing out of leaded gasoline. Twenty years of phasing out of
leaded gasoline in Cairo has greatly improved the lead pollution
among residents of traffic areas, but industrial areas residents were
still suffering from lead pollution, which needs more efforts to
control the sources of lead pollution.
Abstract: Diverse contaminants released into the environment through progress of urbanization and industrialization adversely affect human health. Among various sources of contaminants, especially, in big cities, automobiles play a significant role in aggravating the pollution. Various pollutants viz., heavy metals (Pb, Mn, Ni, Zn, As, Hg, Cd) and Polyaromatic hydrocarbons (Benzo-a-pyrene, fluoranthene, pyrene, benzo-b-anthracene, benzo-b-fluoranthene, acenaphthylene, fluorine, phenantherene, anthracene, chrysene, benzo-k-fluoranthene, benzo-e-pyrene, indenol-1,2,3-cd-pyrene, dibenzo-a,h-anthracene, benzo-ghi-perylene) are released by vehicles. Further, these pollutants are expected to cause severe mutagenic, genotoxic and carcinogenic effects. Considering this, many authors monitored the levels of pollution in roadside soil, water and plants. The present review focuses upon the analysis and effects of heavy metals and polycyclic aromatic hydrocarbons from the roadside samples.
Abstract: Chromium is one of the most common heavy metals which exist in very high concentrations in wastewater. The removal is very expensive due to the high cost of normal adsorbents. Lignocellulosic materials and mainly treated materials have proven to be a good solution for this problem.
Adsorption tests were performed at different pH, different times and with varying concentrations.
Results show that is at pH 3 that treated wood absorbs more chromium ranging from 70% (2h treatment) to almost 100% (12 h treatment) much more than untreated wood with less than 40%. Most of the adsorption is made in the first 2-3 hours for untreated and heat treated wood. Modified wood adsorbs more chromium throughout the time. For all the samples, adsorption fitted relatively well the Langmuir model with correlation coefficient ranging from 0.85 to 0.97.
The results show that heat treated wood is a good adsorbent ant that this might be a good utilization for sawdust from treating companies.
Abstract: This paper aims at experimental and numerical investigation of springback behavior of sheet metals during L-bending process with emphasis on Stribeck-type friction modeling. The coefficient of friction in Stribeck curve depends on sliding velocity and contact pressure. The springback behavior of mild steel and aluminum alloy 6022-T4 sheets was studied experimentally and using numerical simulations with ABAQUS software with two types of friction model: Coulomb friction and Stribeck friction. The influence of forming speed on springback behavior was studied experimentally and numerically. The results showed that Stribeck-type friction model has better results in predicting springback in sheet metal forming. The FE prediction error for mild steel and 6022-T4 AA is 23.8%, 25.5% respectively, using Coulomb friction model and 11%, 13% respectively, using Stribeck friction model. These results show that Stribeck model is suitable for simulation of sheet metal forming especially at higher forming speed.
Abstract: Composting is a controlled technology to enhance the
natural aerobic process of organic wastes degradation. The resulting
product is a humified material that is principally recyclable for
agricultural purpose. The composting process is one of the most
important tools for waste management, by the European Community
legislation. In recent years composting has been increasingly used as
a remediation technology to remove biodegradable contaminants
from soil, and to modulate heavy metals bioavailability in
phytoremediation strategies. An optimization in the recovery of
resources from wastes through composting could enhance soil
fertility and promote its use in the remediation biotechnologies of
contaminated soils.
Abstract: The design of multi stage deep drawing processes requires the evaluation of many process parameters such as the intermediate die geometry, the blank shape, the sheet thickness, the blank holder force, friction, lubrication etc..These process parameters have to be determined for the optimum forming conditions before the process design. In general sheet metal forming may involve stretching drawing or various combinations of these basic modes of deformation. It is important to determine the influence of the process variables in the design of sheet metal working process. Especially, the punch and die corner for deep drawing will affect the formability. At the same time the prediction of sheet metals springback after deep drawing is an important issue to solve for the control of manufacturing processes. Nowadays, the importance of this problem increases because of the use of steel sheeting with high stress and also aluminum alloys.
The aim of this paper is to give a better understanding of the springback and its effect in various sheet metals forming process such as expansion and restreint deep drawing in the cup drawing process, by varying radius die, lubricant for two commercially available materials e.g. galvanized steel and Aluminum sheet. To achieve these goals experiments were carried out and compared with other results. The original of our purpose consist on tests which are ensured by adapting a U-type stretching-bending device on a tensile testing machine, where we studied and quantified the variation of the springback.
Abstract: Soil is a complex physical and biological system that provides support, water, nutrients and oxygen to the plants. Apart from these, it acts as a connecting link between inorganic, organic and living components of the ecosystem. In recent years, presence of xenobiotics, alterations in the natural soil environment, application of pesticides/inorganic fertilizers, percolation of contaminated surface water as well as leachates from landfills to subsurface strata and direct discharge of industrial wastes to the land have resulted in soil pollution which in turn has posed severe threats to human health especially in terms of causing carcinogenicity by direct DNA damage. The present review is an attempt to summarize literature on sources of soil pollution, characterization of pollutants and their consequences in different living systems.
Abstract: The lignite-fired power plants in the Western Macedonia Lignite Center produce more than 8106 t of fly ash per year. Approximately 90% of this quantity is used for restoration-reclamation of exhausted open-cast lignite mines and slope stabilization of the overburden. The purpose of this work is to evaluate the environmental behavior of the mixture of waste rock and fly ash that is being used in the external deposition site of the South Field lignite mine. For this reason, a borehole was made within the site and 86 samples were taken and subjected to chemical analyses and leaching tests. The results showed very limited leaching of trace elements and heavy metals from this mixture. Moreover, when compared to the limit values set for waste acceptable in inert waste landfills, only few excesses were observed, indicating only minor risk for groundwater pollution. However, due to the complexity of both the leaching process and the contaminant pathway, more boreholes and analyses should be made in nearby locations and a systematic groundwater monitoring program should be implemented both downstream and within the external deposition site.
Abstract: Materials with ultrafine-grained structure and unique physical and mechanical properties can be obtained by methods of severe plastic deformation, which include processes of asymmetric rolling (AR). Asymmetric rolling is a very effective way to create ultrafine-grained structures of metals and alloys. Since the asymmetric rolling is a continuous process, it has great potential for industrial production of ultrafine-grained structure sheets. Basic principles of asymmetric rolling are described in detail in scientific literature. In this work finite element modeling of asymmetric rolling and metal forming processes in multiroll gauge was performed. Parameters of the processes which allow achieving significant values of shear strain were defined. The results of the study will be useful for the research of the evolution of ultra-fine metal structure in asymmetric rolling.
Abstract: The heavy metals pollution in water, sediments and fish of Lake Manzala affected form the disposal of wastewater, industrial and agricultural drainage water into the lake on the environmental situation. A pilot plant with an industrial discharge flow of 135L/h designed according to the activated sludge plant to simulate between the biological and chemical treatment with the addition of alum to the aeration tank with dosages of 100, 150, 200 and 250 mg/L. The industrial discharge had concentrations of Lead and BOD5 with an average range 1.22, 145mg/L respectively. That means the average Pb was high up to 25 times than the allowed permissible concentration. The optimization of the chemical-biological process using 200mg/L Alum dosage compared has improvement of Lead and BOD5 removal efficiency to 61.76% and 56% respectively.