Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: Recordings from recent earthquakes have provided evidence that ground motions in the near field of a rupturing fault differ from ordinary ground motions, as they can contain a large energy, or “directivity" pulse. This pulse can cause considerable damage during an earthquake, especially to structures with natural periods close to those of the pulse. Failures of modern engineered structures observed within the near-fault region in recent earthquakes have revealed the vulnerability of existing RC buildings against pulse-type ground motions. This may be due to the fact that these modern structures had been designed primarily using the design spectra of available standards, which have been developed using stochastic processes with relatively long duration that characterizes more distant ground motions. Many recently designed and constructed buildings may therefore require strengthening in order to perform well when subjected to near-fault ground motions. Fiber Reinforced Polymers are considered to be a viable alternative, due to their relatively easy and quick installation, low life cycle costs and zero maintenance requirements. The objective of this paper is to investigate the adequacy of Artificial Neural Networks (ANN) to determine the three dimensional dynamic response of FRP strengthened RC buildings under the near-fault ground motions. For this purpose, one ANN model is proposed to estimate the base shear force, base bending moments and roof displacement of buildings in two directions. A training set of 168 and a validation set of 21 buildings are produced from FEA analysis results of the dynamic response of RC buildings under the near-fault earthquakes. It is demonstrated that the neural network based approach is highly successful in determining the response.
Abstract: This paper presents a model for analysis the induced voltage of transmission lines (energized) acting on neighboring distribution lines (de-energized). From environmental restrictions, 22 kV distribution lines need to be installed under 115 kV transmission lines. With the installation of the two parallel circuits like this, they make the induced voltage which can cause harm to operators. This work was performed with the ATP-EMTP modeling to analyze such phenomenon before field testing. Simulation results are used to find solutions to prevent danger to operators who are on the pole.
Abstract: Biogas, a clean renewable energy, is attracting a growing
concern of researchers and professionals in many fields. Based
on the natural and climatic conditions in semi-arid regions of northwestern
China, the present study introduces a specifically-designed
family-size biogas plant (with a digester of 10m3) with manure
and urine of animals and humanity as raw materials. The biogas
plant is applicable to areas with altitudes of more than 2000 meters
in northwestern China. In addition to the installation cost, a little
operational expenditure, structure, characteristics, benefits of this
small-scale biogas plant, this article introduces a wide range of
specific popularization methods such as training, financial support,
guided tour to the biogas plant, community-based group study and
delivery of operational manuals. The feasibility of the biogas plant is
explored on the basis of the availability of the raw materials. Simple
operations contained in the current work increase the possibility of
the wide use of this small-scale biogas plant in similar regions of the
world.
Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: Traditional development of wireless sensor network
mote is generally based on SoC1 platform. Such method of
development faces three main drawbacks: lack of flexibility in terms
of development due to low resource and rigid architecture of SoC;
low capability of evolution and portability versus performance if
specific micro-controller architecture features are used; and the rapid
obsolescence of micro-controller comparing to the long lifetime of
power plants or any industrial installations. To overcome these
drawbacks, we have explored a new approach of development of
wireless sensor network mote using a hybrid FPGA technology. The
application of such approach is illustrated through the
implementation of an innovative wireless sensor network protocol
called OCARI.
Abstract: A preliminary evaluation of the feasibility of installing small wind turbines on offshore oil and gas extraction platforms is presented. Some aerodynamic considerations are developed in order to determine the best rotor architecture to exploit the wind potential on such installations, assuming that wind conditions over the platforms are similar to those registered on the roofs of urban buildings. Economical considerations about both advantages and disadvantages of the exploitation of wind energy on offshore extraction platforms with respect to conventional offshore wind plants, is also presented. Finally, wind charts of European offshore winds are presented together with a map of the major offshore installations.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: The sensitivity of orifice plate metering to disturbed
flow (either asymmetric or swirling) is a subject of great concern to
flow meter users and manufacturers. The distortions caused by pipe
fittings and pipe installations upstream of the orifice plate are major
sources of this type of non-standard flows. These distortions can alter
the accuracy of metering to an unacceptable degree. In this work, a
multi-scale object known as metal foam has been used to generate a
predetermined turbulent flow upstream of the orifice plate. The
experimental results showed that the combination of an orifice plate
and metal foam flow conditioner is broadly insensitive to upstream
disturbances. This metal foam demonstrated a good performance in
terms of removing swirl and producing a repeatable flow profile
within a short distance downstream of the device. The results of using
a combination of a metal foam flow conditioner and orifice plate for
non-standard flow conditions including swirling flow and asymmetric
flow show this package can preserve the accuracy of metering up to
the level required in the standards.
Abstract: This paper aims to develop a NOx emission model of
an acid gas incinerator using Nelder-Mead least squares support
vector regression (LS-SVR). Malaysia DOE is actively imposing the
Clean Air Regulation to mandate the installation of analytical
instrumentation known as Continuous Emission Monitoring System
(CEMS) to report emission level online to DOE . As a hardware
based analyzer, CEMS is expensive, maintenance intensive and often
unreliable. Therefore, software predictive technique is often
preferred and considered as a feasible alternative to replace the
CEMS for regulatory compliance. The LS-SVR model is built based
on the emissions from an acid gas incinerator that operates in a LNG
Complex. Simulated Annealing (SA) is first used to determine the
initial hyperparameters which are then further optimized based on the
performance of the model using Nelder-Mead simplex algorithm.
The LS-SVR model is shown to outperform a benchmark model
based on backpropagation neural networks (BPNN) in both training
and testing data.
Abstract: Demand of energy is increasing faster than the
generation. It leads shortage of power in all sectors of society. At
peak hours this shortage is higher. Unless we utilize energy efficient
technology, it is very difficult to minimize the shortage of energy. So
energy efficiency program and energy conservation has an important
role. Energy efficient technologies are cost intensive hence it is
always not possible to implement in country like India. In the recent
study, an educational building with operating hours from 10:00 a.m.
to 05:00 p.m. has been selected to quantify the possibility of lighting
energy conservation. As the operating hour is in daytime, integration
of daylight with artificial lighting system will definitely reduce the
lighting energy consumption. Moreover the initial investment has
been given priority and hence the existing lighting installation was
unaltered. An automatic controller has been designed which will be
operated as a function of daylight through windows and the lighting
system of the room will function accordingly. The result of the study
of integrating daylight gave quite satisfactory for visual comfort as
well as energy conservation.
Abstract: Explosions may cause intensive damage to buildings
and sometimes lead to total and progressive destruction. Pressures
induced by explosions are one of the most destructive loads a
structure may experience. While designing structures for great
explosions may be expensive and impractical, engineers are looking
for methods for preventing destructions resulted from explosions. A
favorable structural system is a system which does not disrupt totally
due to local explosion, since such structures sustain less loss in
comparison with structural ones which really bear the load and
suddenly disrupt. Designing and establishing vital and necessary
installations in a way that it is resistant against direct hit of bomb and
rocket is not practical, economical, or expedient in many cases,
because the cost of construction and installation with such
specifications is several times more than the total cost of the related
equipment.
Abstract: The continuity in the electric supply of the electric installations is becoming one of the main requirements of the electric supply network (generation, transmission, and distribution of the electric energy). The achievement of this requirement depends from one side on the structure of the electric network and on the other side on the avaibility of the reserve source provided to maintain the supply in case of failure of the principal one. The avaibility of supply does not only depends on the reliability parameters of the both sources (principal and reserve) but it also depends on the reliability of the circuit breaker which plays the role of interlocking the reserve source in case of failure of the principal one. In addition, the principal source being under operation, its control can be ideal and sure, however, for the reserve source being in stop, a preventive maintenances which proceed on time intervals (periodicity) and for well defined lengths of time are envisaged, so that this source will always available in case of the principal source failure. The choice of the periodicity of preventive maintenance of the source of reserve influences directly the reliability of the electric feeder system In this work and on the basis of the semi- markovian's processes, the influence of the time of interlocking the reserve source upon the reliability of an industrial electric network is studied and is given the optimal time of interlocking the reserve source in case of failure the principal one, also the influence of the periodicity of the preventive maintenance of the source of reserve is studied and is given the optimal periodicity.
Abstract: The autonomous mobile robot was designed and implemented which was capable of navigating in the industrial environments and did a job of picking objects from variable height and delivering it to another location following a predefined trajectory. In developing country like Bangladesh industrial robotics is not very prevalent yet, due to the high installation cost. The objective of this project was to develop an autonomous mobile robot for industrial application using the available resources in the local market at lower manufacturing cost. The mechanical system of the robot was comprised of locomotion, gripping and elevation system. Grippers were designed to grip objects of a predefined shape. Cartesian elevation system was designed for vertical movement of the gripper. PIC18F452 microcontroller was the brain of the control system. The prototype autonomous robot was fabricated for relatively lower load than the industry and the performance was tested in a virtual industrial environment created within the laboratory to realize the effectiveness.
Abstract: Introducing Electromagnetic Interference and Electromagnetic Compatibility, or “The Art of Black Magic", for engineering students might be a terrifying experience both for students and tutors. Removing the obstacle of large, expensive facilities like a fully fitted EMC laboratory and hours of complex theory, this paper demonstrates a design of a laboratory setup for student exercises, giving students experience in the basics of EMC/EMI problems that may challenge the functionality and stability of embedded system designs. This is done using a simple laboratory installation and basic measurement equipment such as a medium cost digital storage oscilloscope, at the cost of not knowing the exact magnitude of the noise components, but rather if the noise is significant or not, as well as the source of the noise. A group of students have performed a trial exercise with good results and feedback.
Abstract: Policies that support entrepreneurship are keys to the
generation of new business. In Brazil, seed capital, installation of
technology parks, programs and zero interest financing, economic
subsidy as Program First Innovative Company (PRIME) are
examples of incentive policies. For the implementation of PRIME, in
particular the Brazilian Innovation Agency (FINEP) decentralized
operationalization so that business incubators could select innovative
projects. This paper analyzes the program PRIME Business Incubator
Center of the State of Sergipe (CISE) after calculating the mean and
standard deviation of the grades obtained by companies in the factors
of innovation, market potential, financial return economic, market
strategy and staff and application of the Mann-Whitney test.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.
Abstract: Rotational Smart Lighting Control System can supply
the quantity of lighting which is required to run plants by rotating few
LED and Fluorescent instead of that are used in the existing plant
factories.The initial installation of the existing plants factory is
expensive, so in order to solve the problem with smart lighting control
system was developed.
The beam required intensity for the growth of crops, Photosynthetic
Photon Flux Density(PPFD)is calculated; and the number of LED, are
installed on the blades, set; using the Lighting Simulation
Program.Relux, it is able to confirm that the difference of the beam
intensity between the center and the outer of lighting system when the
lighting device is rotating.
Abstract: Due to the increasing penetration of wind energy, it is
necessary to possess design tools that are able to simulate the impact
of these installations in utility grids. In order to provide a net
contribution to this issue a detailed wind park model has been
developed and is briefly presented. However, the computational costs
associated with the performance of such a detailed model in
describing the behavior of a wind park composed by a considerable
number of units may render its practical application very difficult. To
overcome this problem integral manifolds theory has been applied to
reduce the order of the detailed wind park model, and therefore
create the conditions for the development of a dynamic equivalent
which is able to retain the relevant dynamics with respect to the
existing a.c. system. In this paper integral manifold method has been
introduced for order reduction. Simulation results of the proposed
method represents that integral manifold method results fit the
detailed model results with a higher precision than singular
perturbation method.
Abstract: Presents a concept for a multidisciplinary process
supporting effective task transitions between different technical
domains during the architectural design stage.
A system configuration challenge is the multifunctional driven
increased solution space. As a consequence, more iteration is needed
to find a global optimum, i.e. a compromise between involved
disciplines without negative impact on development time. Since state
of the art standards like ISO 15288 and VDI 2206 do not provide a
detailed methodology on multidisciplinary design process, higher
uncertainties regarding final specifications arise. This leads to the
need of more detailed and standardized concepts or processes which
could mitigate risks.
The performed work is based on analysis of multidisciplinary
interaction, of modeling and simulation techniques. To demonstrate
and prove the applicability of the presented concept, it is applied to
the design of aircraft high lift systems, in the context of the
engineering disciplines kinematics, actuation, monitoring, installation
and structure design.