Abstract: A procedure for the preparation of clarified Pawpaw
Juice was developed. About 750ml Pawpaw pulp was measured into
2 measuring cylinders A & B of capacity 1 litre heated to 400C,
cooled to 200C. 30mls pectinase was added into cylinder A, while
30mls distilled water was added into cylinder B. Enzyme treated
sample (A) was allowed to digest for 5hours after which it was heated
to 900C for 15 minutes to inactivate the enzyme. The heated sample
was cooled and with the aid of a mucillin cloth the pulp was filtered
to obtain the clarified pawpaw juice. The juice was filled into 100ml
plastic bottles, pasteurized at 950C for 45 minutes, cooled and stored
at room temperature. The sample treated with 30mls distilled water
also underwent the same process. Freshly pasteurized sample was
analyzed for specific gravity, titratable acidity, pH, sugars and
ascorbic acid. The remaining sample was then stored for 2 weeks and
the above analyses repeated. There were differences in the results of
the freshly pasteurized samples and stored sample in pH and ascorbic
acid levels, also sample treated with pectinase yielded higher
volumes of juice than that treated with distilled water.
Abstract: A steady two-dimensional magnetohydrodynamics
flow and heat transfer over a stretching vertical sheet influenced by
radiation and porosity is studied. The governing boundary layer
equations of partial differential equations are reduced to a system of
ordinary differential equations using similarity transformation. The
system is solved numerically by using a finite difference scheme
known as the Keller-box method for some values of parameters,
namely the radiation parameter N, magnetic parameter M, buoyancy
parameter l , Prandtl number Pr and permeability parameter K. The
effects of the parameters on the heat transfer characteristics are
analyzed and discussed. It is found that both the skin friction
coefficient and the local Nusselt number decrease as the magnetic
parameter M and permeability parameter K increase. Heat transfer
rate at the surface decreases as the radiation parameter increases.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.
Abstract: It is well recognized that the green house gases such
as Chlorofluoro Carbon (CFC), CH4, CO2 etc. are responsible
directly or indirectly for the increase in the average global temperature
of the Earth. The presence of CFC is responsible for
the depletion of ozone concentration in the atmosphere due to
which the heat accompanied with the sun rays are less absorbed
causing increase in the atmospheric temperature of the Earth. The
gases like CH4 and CO2 are also responsible for the increase in
the atmospheric temperature. The increase in the temperature level
directly or indirectly affects the dynamics of interacting species
systems. Therefore, in this paper a mathematical model is proposed
and analysed using stability theory to asses the effects of increasing
temperature due to greenhouse gases on the survival or extinction of
populations in a prey-predator system. A threshold value in terms
of a stress parameter is obtained which determines the extinction or
existence of populations in the underlying system.
Abstract: This study focuses on examining why the range of
experience with respect to HIV infection is so diverse, especially in
regard to the latency period. An agent-based approach in modelling
the infection is used to extract high-level behaviour which cannot be
obtained analytically from the set of interaction rules at the cellular
level. A prototype model encompasses local variation in baseline
properties, contributing to the individual disease experience, and is
included in a network which mimics the chain of lymph nodes. The
model also accounts for stochastic events such as viral mutations.
The size and complexity of the model require major computational
effort and parallelisation methods are used.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: This study presents an exact general solution for
steady-state conductive heat transfer in cylindrical composite
laminates. Appropriate Fourier transformation has been obtained
using Sturm-Liouville theorem. Series coefficients are achieved by
solving a set of equations that related to thermal boundary conditions
at inner and outer of the cylinder, also related to temperature
continuity and heat flux continuity between each layer. The solution
of this set of equations are obtained using Thomas algorithm. In this
paper, the effect of fibers- angle on temperature distribution of
composite laminate is investigated under general boundary
conditions. Here, we show that the temperature distribution for any
composite laminates is between temperature distribution for
laminates with θ = 0° and θ = 90° .
Abstract: This research evaluated and compared the thermodynamic performance of heat pump systems which can be run under two different modes as air to air and air to water by using only one compressor. To achieve this comparison an experimental performance study was made on a traditional vapor compressed heat pump system that can be run air to air mode and air to water mode by help of a valve. The experiments made under different thermal conditions. Thermodynamic performance of the systems are presented and compared with each other for different working conditions.
Abstract: Attempts to add fibre and polyphenols (PPs) into
popular beverages present challenges related to the properties of
finished products such as smoothies. Consumer acceptability,
viscosity and phenolic composition of smoothies containing high
levels of fruit fibre (2.5-7.5 g per 300 mL serve) and PPs (250-750
mg per 300 mL serve) were examined. The changes in total
extractable PP, vitamin C content, and colour of selected smoothies
over a storage stability trial (4°C, 14 days) were compared. A set of
acidic aqueous model beverages were prepared to further examine
the effect of two different heat treatments on the stability and
extractability of PPs. Results show that overall consumer
acceptability of high fibre and PP smoothies was low, with average
hedonic scores ranging from 3.9 to 6.4 (on a 1-9 scale). Flavour,
texture and overall acceptability decreased as fibre and polyphenol
contents increased, with fibre content exerting a stronger effect.
Higher fibre content resulted in greater viscosity, with an elevated PP
content increasing viscosity only slightly. The presence of fibre also
aided the stability and extractability of PPs after heating. A reduction
of extractable PPs, vitamin C content and colour intensity of
smoothies was observed after a 14-day storage period at 4°C. Two
heat treatments (75°C for 45 min or 85°C for 1 min) that are
normally used for beverage production, did not cause significant
reduction of total extracted PPs. It is clear that high levels of added
fibre and PPs greatly influence the consumer appeal of smoothies,
suggesting the need to develop novel formulation and processing
methods if a satisfactory functional beverage is to be developed
incorporating these ingredients.
Abstract: World population growth drives food demand, promotes intensification of agriculture, development of new production technologies and varieties more suitable for regional nature conditions. Climate change can affect the length of growing period, biomass and carbon accumulation in winter wheat. The increasing mean air temperature resulting from climate change can reduce the length of growth period of cereals, and without adequate adjustments in growing technologies or varieties, can reduce biomass and carbon accumulation. Deeper understanding and effective measures for monitoring and management of cereal growth process are needed for adaptation to changing climate and technological conditions.
Abstract: In this paper the authors propose and verify an approach to control heat flow in machine tool components. Thermal deformations are a main aspect that affects the accuracy of machining. Due to goals of energy efficiency, thermal basic loads should be reduced. This leads to inhomogeneous and time variant temperature profiles. To counteract these negative consequences, material with high melting enthalpy is used as a method for thermal stabilization. The increased thermal capacity slows down the transient thermal behavior. To account for the delayed thermal equilibrium, a control mechanism for thermal flow is introduced. By varying a gap in a heat flow path the thermal resistance of an assembly can be controlled. This mechanism is evaluated in two experimental setups. First to validate the ability to control the thermal resistance and second to prove the possibility of a self-sufficient option based on the selfsensing abilities of thermal shape memory alloys.
Abstract: In this paper, numerical simulation is used to
investigate the thermal performance of liquid cooling heatsink with
microchannels due to geometric arrangement. Commercial software
ICEPAK is utilized for the analysis. The considered parameters
include aspect ratio, porosity and the length and height of
microchannel. The aspect ratio varies from 3 to 16 and the length of
microchannel is 10mm, 14mm, and 18mm. The height of
microchannel is 2mm, 3mm and 4mm. It is found short channel have
better thermal efficiency than long channel at 490Pa. No matter the
length of channel the best aspect ratio is 4. It is also noted that pressure
difference at 2940Pa the best aspect ratio from 4 to 8, it means pressure
difference affect aspect ratio, effective thermal resistance at low
pressure difference but lower effective thermal resistance at high
pressure difference.
Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.