Abstract: Fluid flow and heat transfer of vertical full cone
embedded in porous media is studied in this paper. Nonlinear
differential equation arising from similarity solution of inverted cone
(subjected to wall temperature boundary conditions) embedded in
porous medium is solved using a hybrid neural network- particle
swarm optimization method.
To aim this purpose, a trial solution of the differential equation is
defined as sum of two parts. The first part satisfies the initial/
boundary conditions and does contain an adjustable parameter and
the second part which is constructed so as not to affect the
initial/boundary conditions and involves adjustable parameters (the
weights and biases) for a multi-layer perceptron neural network.
Particle swarm optimization (PSO) is applied to find adjustable
parameters of trial solution (in first and second part). The obtained
solution in comparison with the numerical ones represents a
remarkable accuracy.
Abstract: The mechanism of microwave heating is essentially
that of dielectric heating. After exposing the emulsion to the
microwave Electromagnetic (EM) field, molecular rotation and ionic
conduction due to the penetration of (EM) into the emulsion are
responsible for the internal heating. To determine the capability of
microwave technology in demulsification of crude oil emulsions,
microwave demulsification method was applied in a 50-50 % and 20-
80 % water-in-oil emulsions with microwave exposure time varied
from 20-180 sec. Transient temperature profiles of water-in-oil
emulsions inside a cylindrical container were measured. The
temperature rise at a given location was almost horizontal (linear).
The average rates of temperature increase of 50-50 % and 20-80 %
water-in-oil emulsions are 0.351 and 0.437 oC/sec, respectively. The
rate of temperature increase of emulsions decreased at higher
temperature due to decreasing dielectric loss of water. These results
indicate that microwave demulsification of water-in-oil emulsions
does not require chemical additions. Microwave has the potential to
be used as an alternative way in the demulsification process.
Abstract: This work focuses on analysis of classical heat transfer equation regularized with Maxwell-Cattaneo transfer law. Computer simulations are performed in MATLAB environment. Numerical experiments are first developed on classical Fourier equation, then Maxwell-Cattaneo law is considered. Corresponding equation is regularized with a balancing diffusion term to stabilize discretizing scheme with adjusted time and space numerical steps. Several cases including a convective term in model equations are discussed, and results are given. It is shown that limiting conditions on regularizing parameters have to be satisfied in convective case for Maxwell-Cattaneo regularization to give physically acceptable solutions. In all valid cases, uniform convergence to solution of initial heat equation with Fourier law is observed, even in nonlinear case.
Abstract: Employees commonly encounter unpredictable and
unavoidable work related stressors. Exposure to such stressors can
evoke negative appraisals and associated adverse mental, physical,
and behavioral responses. Because Acceptance and Commitment
Therapy (ACT) emphasizes acceptance of unavoidable stressors and
diffusion from negative appraisals, it may be particularly beneficial
for work stress. Forty-five workers were randomly assigned to an
ACT intervention for work stress (n = 21) or a waitlist control group
(n = 24). The intervention consisted of two 3-hour sessions spaced
one week apart. An examination of group process and outcomes was
conducted using the Revised Sessions Rating Scale. Results indicated
that the ACT participants reported that they perceived the
intervention to be supportive, task focused, and without adverse
therapist behaviors (e.g., feelings of being criticized or discounted).
Additionally, the second session (values clarification and
commitment to action) was perceived to be more supportive and task
focused than the first session (mindfulness, defusion). Process ratings
were correlated with outcomes. Results indicated that perceptions of
therapy supportiveness and task focus were associated with reduced
psychological distress and improved perceived physical health.
Abstract: The fortified of soft wheat flour with cowpea flour in
bread making was investigated. The Soft wheat flour (SWF) was
substituted by cowpea flour at levels of 5, 15 and 20%. The protein content of composite breads ranged from 6.1 – 9.9%. Significant
difference was observed in moisture, protein and crude fibre contents of control (wheat bread) and composite bread at 5% addition of
cowpea. Water absorption capacities of composite flours increased with increasing levels of cowpea flour in the blend. The specific loaf
volume decreased significantly with increased cowpea content of
blends. The overall acceptability of the 5% cowpea flour content of
composite bread was not significantly different from the control (Soft Wheat-bread) but there is significantly different with increasing the
levels of cowpea flour in the blend more than 5%.
Abstract: We successfully developed a new straw combustion
technology that efficiently reduces problems with unmanageable deposits inside straw fueled boilers in Zluticka Heating Plant. The
deposits are mainly created by glass-forming melts. We plotted straw compositions in K2O-CaO-SiO2 phase diagram and illustrated
they are in the area of low-melting eutectic poi
melting of ash and the formation of deposits
compositions by injecting additives into biomass fuel
ueled points. To prevent the
deposits, we modified ash
fuel.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: The crystallization kinetics and phase transformation
of SiO2.Al2O3.0,56P2O5.1,8CaO.0,56CaF2 glass have been
investigated using differential thermal analysis (DTA), x-ray
diffraction (XRD), and scanning electron microscopy (SEM). Glass
samples were obtained by melting the glass mixture at 14500С/120
min. in platinum crucibles. The mixture were prepared from
chemically pure reagents: SiO2, Al(OH)3, H3PO4, CaCO3 and CaF2.
The non-isothermal kinetics of crystallization was studied by
applying the DTA measurements carried out at various heating rates.
The activation energies of crystallization and viscous flow were
measured as 348,4 kJ.mol–1 and 479,7 kJ.mol–1 respectively. Value of
Avrami parameter n ≈ 3 correspond to a three dimensional of crystal
growth mechanism. The major crystalline phase determined by XRD
analysis was fluorapatite (Ca(PO4)3F) and as the minor phases –
fluormargarite (CaAl2(Al2SiO2)10F2) and vitlokite (Ca9P6O24). The
resulting glass-ceramic has a homogeneous microstructure, composed
of prismatic crystals, evenly distributed in glass phase.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: A method to determine experimentally the melting
rate, rm, and the heat transfer coefficients, αv (W/(m3K)), at
convective melting in a fixed bed of particles under adiabatic regime
is established in this paper. The method lies in the determining of the
melting rate by measuring the fixed bed height in time. Experimental
values of rm, α and α v were determined using cylindrical particles of
ice (d = 6.8 mm, h = 5.5 mm) and, as a melting agent, aqueous NaCl
solution with a temperature of 283 K at different values of the liquid
flow rate (11.63·10-6, 28.83·10-6, 38.83·10-6 m3/s).
Our experimental results were compared with those existing in
literature being noticed a good agreement for Re values higher than
50.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: A parallel computational fluid dynamics code has been
developed for the study of aerodynamic heating problem in hypersonic
flows. The code employs the 3D Navier-Stokes equations as the basic
governing equations to simulate the laminar hypersonic flow. The cell
centered finite volume method based on structured grid is applied for
spatial discretization. The AUSMPW+ scheme is used for the inviscid
fluxes, and the MUSCL approach is used for higher order spatial
accuracy. The implicit LU-SGS scheme is applied for time integration
to accelerate the convergence of computations in steady flows. A
parallel programming method based on MPI is employed to shorten
the computing time. The validity of the code is demonstrated by
comparing the numerical calculation result with the experimental data
of a hypersonic flow field around a blunt body.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: In this work, thermoelastic damping effect on the hemi- spherical shells is investigated. The material is selected silicon, and heat conduction equation for thermal flow is solved to obtain the temperature profile in which bending approximation with inextensional assumption of the model. Using the temperature profile, eigen-value analysis is performed to get the natural frequencies of hemispherical shells. Effects of mode numbers, radii and radial thicknesses of the model on the natural frequencies are analyzed in detail. Furthermore, the quality factor (Q-factor) is defined, and discussed for the ring and hemispherical shell.
Abstract: In this paper the development of a heat exchanger as a
pilot plant for educational purpose is discussed and the use of neural
network for controlling the process is being presented. The aim of the
study is to highlight the need of a specific Pseudo Random Binary
Sequence (PRBS) to excite a process under control. As the neural
network is a data driven technique, the method for data generation
plays an important role. In light of this a careful experimentation
procedure for data generation was crucial task. Heat exchange is a
complex process, which has a capacity and a time lag as process
elements. The proposed system is a typical pipe-in- pipe type heat
exchanger. The complexity of the system demands careful selection,
proper installation and commissioning. The temperature, flow, and
pressure sensors play a vital role in the control performance. The
final control element used is a pneumatically operated control valve.
While carrying out the experimentation on heat exchanger a welldrafted
procedure is followed giving utmost attention towards safety
of the system. The results obtained are encouraging and revealing
the fact that if the process details are known completely as far as
process parameters are concerned and utilities are well stabilized then
feedback systems are suitable, whereas neural network control
paradigm is useful for the processes with nonlinearity and less
knowledge about process. The implementation of NN control
reinforces the concepts of process control and NN control paradigm.
The result also underlined the importance of excitation signal
typically for that process. Data acquisition, processing, and
presentation in a typical format are the most important parameters
while validating the results.
Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: The present study is concerned with the effect of
exciting boundary layer on cooling process in a gas-turbine blades.
The cooling process is numerically investigated. Observations show
cooling the first row of moving or stable blades leads to increase
their life-time. Results show that minimum temperature in cooling
line with exciting boundary layer is lower than without exciting.
Using block in cooling line of turbines' blade causes flow pattern and
stability in boundary layer changed that causes increase in heat
transfer coefficient. Results show at the location of block,
temperature of turbines' blade is significantly decreased. The k-ε
turbulence model is used.
Abstract: The scope of this research was to study the relation between the facial expressions of three lecturers in a real academic lecture theatre and the reactions of the students to those expressions. The first experiment aimed to investigate the effectiveness of a virtual lecturer-s expressions on the students- learning outcome in a virtual pedagogical environment. The second experiment studied the effectiveness of a single facial expression, i.e. the smile, on the students- performance. Both experiments involved virtual lectures, with virtual lecturers teaching real students. The results suggest that the students performed better by 86%, in the lectures where the lecturer performed facial expressions compared to the results of the lectures that did not use facial expressions. However, when simple or basic information was used, the facial expressions of the virtual lecturer had no substantial effect on the students- learning outcome. Finally, the appropriate use of smiles increased the interest of the students and consequently their performance.
Abstract: The stability of Newtonian and Non-Newtonian extending films under local or global heating or cooling conditions are considered. The thickness-averaged mass, momentum and energy equations with convective and radiative heat transfer are derived, both for Newtonian and non-Newtonian fluids (Maxwell, PTT and Giesekus models considered). The stability of the system is explored using either eigenvalue analysis or transient simulations. The results showed that the influence of heating and cooling on stability strongly depends on the magnitude of the Peclet number. Examples of stabilization or destabilization of heating or cooling are shown for Pe