Abstract: In this study thermodynamic performance analysis of a
combined organic Rankine cycle and ejector refrigeration cycle is
carried out for use of low-grade heat source in the form of sensible
energy. Special attention is paid to the effects of system parameters
including the turbine inlet temperature and turbine inlet pressure on the
characteristics of the system such as ratios of mass flow rate, net work
production, and refrigeration capacity as well as the coefficient of
performance and exergy efficiency of the system. Results show that
for a given source the coefficient of performance increases with
increasing of the turbine inlet pressure. However, the exergy
efficiency has an optimal condition with respect to the turbine inlet
pressure.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: Arc welding creates a weld pool to realize continuity between pieces of assembly. The thermal history of the weld is dependent on heat transfer and fluid flow in the weld pool. The metallurgical transformation during welding and cooling are modeled in the literature only at solid state neglecting the fluid flow. In the present paper we associate a heat transfer – fluid flow and metallurgical model for the 16MnD5 steel. The metallurgical transformation model is based on Leblond model for the diffusion kinetics and on the Koistinen-Marburger equation for Marteniste transformation. The predicted thermal history and metallurgical transformations are compared to a simulation without fluid phase. This comparison shows the great importance of the fluid flow modeling.
Abstract: Recently, the advanced technologies that offer high
precision product, relative easy, economical process and also rapid
production are needed to realize the high demand of ultra precision
micro part. In our research, micromanufacturing based on soft
lithography and nanopowder injection molding was investigated. The
silicone metal pattern with ultra thick and high aspect ratio succeeds to
fabricate Polydimethylsiloxane (PDMS) micro mold. The process
followed by nanopowder injection molding (PIM) by a simple vacuum
hot press. The 17-4ph nanopowder with diameter of 100 nm, succeed
to be injected and it forms green sample microbearing with thickness,
microchannel and aspect ratio is 700μm, 60μm and 12, respectively.
Sintering process was done in 1200 C for 2 hours and heating rate
0.83oC/min. Since low powder load (45% PL) was applied to achieve
green sample fabrication, ~15% shrinkage happen in the 86% relative
density. Several improvements should be done to produce high
accuracy and full density sintered part.
Abstract: Thermoelastic temperature, displacement, and
stress in heat transfer during laser surface hardening are solved
in Eulerian formulation. In Eulerian formulations the heat flux
is fixed in space and the workpiece is moved through a control
volume. In the case of uniform velocity and uniform heat flux
distribution, the Eulerian formulations leads to a steady-state
problem, while the Lagrangian formulations remains transient.
In Eulerian formulations the reduction to a steady-state
problem increases the computational efficiency. In this study
also an analytical solution is developed for an uncoupled
transient heat conduction equation in which a plane slab is
heated by a laser beam. The thermal result of the numerical
model is compared with the result of this analytical model.
Comparing the results shows numerical solution for uncoupled
equations are in good agreement with the analytical solution.
Abstract: This paper presents a time control liquids mixing
system in the tanks as an application of fuzzy time control discrete
model. The system is designed for a wide range of industrial
applications. The simulation design of control system has three
inputs: volume, viscosity, and selection of product, along with the
three external control adjustments for the system calibration or to
take over the control of the system autonomously in local or
distributed environment. There are four controlling elements: rotatory
motor, grinding motor, heating and cooling units, and valves
selection, each with time frame limit. The system consists of three
controlled variables measurement through its sensing mechanism for
feed back control. This design also facilitates the liquids mixing
system to grind certain materials in tanks and mix with fluids under
required temperature controlled environment to achieve certain
viscous level. Design of: fuzzifier, inference engine, rule base,
deffuzifiers, and discrete event control system, is discussed. Time
control fuzzy rules are formulated, applied and tested using
MATLAB simulation for the system.
Abstract: In this study, the powders of Ni and Ti with 50.5 at.%
Ni for 12 h were blended and cold pressed at the different pressures
(50, 75 and100 MPa).The porous product obtained after Ni-Ti
compacts were synthesized by SHS (self-propagating hightemperature
synthesis) in the different preheating temperatures (200,
250 and 300oC) and heating rates (30, 60 and 90oC/min). The effects
of the pressure, preheating temperature and heating rate were
investigated on biocompatibility in vivo. The porosity in the
synthesized products was in the range of 50.7–59.7 vol. %. The
pressure, preheating temperature and heating rate were found to have
an important effect on the biocompatibility in-vivo of the synthesized
products. Max. fibrotic tissue within the porous implant was found in
vivo periods (6 months), in which compacting pressure 100MPa.
Abstract: We report on the development of a model to
understand why the range of experience with respect to HIV
infection is so diverse, especially with respect to the latency period.
To investigate this, an agent-based approach is used to extract highlevel
behaviour which cannot be described analytically from the set
of interaction rules at the cellular level. A network of independent
matrices mimics the chain of lymph nodes. Dealing with massively
multi-agent systems requires major computational effort. However,
parallelisation methods are a natural consequence and advantage of
the multi-agent approach and, using the MPI library, are here
implemented, tested and optimized. Our current focus is on the
various implementations of the data transfer across the network.
Three communications strategies are proposed and tested, showing
that the most efficient approach is communication based on the
natural lymph-network connectivity.
Abstract: We demonstrate a 1×4 coarse wavelength
division-multiplexing (CWDM) planar concave grating
multiplexer/demultiplexer and its application in re-configurable
optical add/drop multiplexer (ROADM) system in silicon-on-insulator
substrate. The wavelengths of the demonstrated concave grating
multiplexer align well with the ITU-T standard. We demonstrate a
prototype of ROADM comprising two such concave gratings and four
wide-band thermo-optical MZI switches. Undercut technology which
removes the underneath silicon substrate is adopted in optical switches
in order to minimize the operation power. For all the thermal heaters,
the operation voltage is smaller than 1.5 V, and the switch power is
~2.4 mW. High throughput pseudorandom binary sequence (PRBS)
data transmission with up to 100 Gb/s is demonstrated, showing the
high-performance ROADM functionality.
Abstract: Periodic vortex shedding in pulsating flow inside wavy
channel and the effect it has on heat transfer are studied using the
finite volume method. A sinusoidally-varying component is superimposed
on a uniform flow inside a sinusoidal wavy channel and
the effects on the Nusselt number is analyzed. It was found that a
unique optimum value of the pulsation frequency, represented by the
Strouhal number, exists for Reynolds numbers ranging from 125 to
1000. Results suggest that the gain in heat transfer is related to the
process of vortex formation, movement about the troughs of the wavy
channel, and subsequent ejection/destruction through the converging
section. Heat transfer is the highest when the frequencies of the
pulsation and vortex formation approach being in-phase. Analysis of
Strouhal number effect on Nu over a period of pulsation substantiates
the proposed physical mechanism for enhancement. The effect of
changing the amplitude of pulsation is also presented over a period
of pulsation, showing a monotonic increase in heat transfer with
increasing amplitude. The 60% increase in Nusselt number suggests
that sinusoidal fluid pulsation can an effective method for enhancing
heat transfer in laminar, wavy-channel flows.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This is caused by the motion of ions generated around the smaller of the two electrodes and their subsequent interaction with the surrounding medium. If one of the electrodes is heated, it changes the conditions around the capacitor
and influences the process of ionisation, thus changing the value of the generated force. This paper describes these changes and gives
reasons behind them. Further the experimental results are given as proof of the ionic mechanism of the phenomenon.
Abstract: In the national and professional music of oral tradition
of many people in the East there is the metric formula called “ussuli",
that is to say rhythmic constructions of different character and a
composition. Ussuli in translation from Arabic means the law. The
cultural contacts of the ancient and medieval inhabitants of the
Central Asia, India, China, East Turkestan, Iraq, Afghanistan,
Turkey, and Iran have played a certain role in formation of both
musical and dancing heritage of each of these people. During
theatrical shows many dances were performed under the
accompaniment of percussion instruments as nagra, dayulpaz, doll.
The abovementioned tools are used as the obligatory accompanying
tool in an orchestra and at support of dancing acts as the solo tool.
Dynamics of development of a dancing composition, at times
execution of technique of movement depends on various
combinations of ussuli and their receptions of execution.
Abstract: In this work, the natural convection in a concentric
annulus between a cold outer inclined square enclosure and heated
inner circular cylinder is simulated for two-dimensional steady
state. The Boussinesq approximation was applied to model the
buoyancy-driven effect and the governing equations were solved
using the time marching approach staggered by body fitted
coordinates. The coordinate transformation from the physical
domain to the computational domain is set up by an analytical
expression. Numerical results for Rayleigh numbers 103 , 104 , 105
and 106, aspect ratios 1.5 , 3.0 and 4.5 for seven different
inclination angles for the outer square enclosure 0o , -30o
, -45o
,
-60o , -90o , -135o , -180o are presented as well. The computed flow
and temperature fields were demonstrated in the form of
streamlines, isotherms and Nusselt numbers variation. It is found
that both the aspect ratio and the Rayleigh number are critical to the
patterns of flow and thermal fields. At all Rayleigh numbers angle
of inclination has nominal effect on heat transfer.
Abstract: The effects of enzyme action and heat pretreatment on oil extraction yield from sunflower kernels were analysed using hexane extraction with Soxhlet, and aqueous extraction with incubator shaker. Ground kernels of raw and heat treated kernels, each with and without Viscozyme treatment were used. Microscopic images of the kernels were taken to analyse the visible effects of each treatment on the cotyledon cell structure of the kernels. Heat pretreated kernels before both extraction processes produced enhanced oil extraction yields than the control, with steam explosion the most efficient. In hexane extraction, applying a combination of steam explosion and Viscozyme treatments to the kernels before the extraction gave the maximum oil extractable in 1 hour; while for aqueous extraction, raw kernels treated with Viscozyme gave the highest oil extraction yield. Remarkable cotyledon cell disruption was evident in kernels treated with Viscozyme; whereas steam explosion and conventional heat treated kernels had similar effects.
Abstract: The problem of laminar fluid flow which results from
the shrinking of a permeable surface in a nanofluid has been
investigated numerically. The model used for the nanofluid
incorporates the effects of Brownian motion and thermophoresis. A
similarity solution is presented which depends on the mass suction
parameter S, Prandtl number Pr, Lewis number Le, Brownian motion
number Nb and thermophoresis number Nt. It was found that the
reduced Nusselt number is decreasing function of each dimensionless
number.
Abstract: This paper presents a unified approach based graph
theory and system theory postulates for the modeling and analysis
of Simple open cycle Gas turbine system. In the present paper, the
simple open cycle gas turbine system has been modeled up to its subsystem
level and system variables have been identified to develop the
process subgraphs. The theorems and algorithms of the graph theory
have been used to represent behavioural properties of the system like
rate of heat and work transfers rates, pressure drops and temperature
drops in the involved processes of the system. The processes have
been represented as edges of the process subgraphs and their limits
as the vertices of the process subgraphs. The system across variables
and through variables has been used to develop terminal equations of
the process subgraphs of the system. The set of equations developed
for vertices and edges of network graph are used to solve the system
for its process variables.
Abstract: A satellite is being integrated and tested by BISEE (Beijing Institute of Spacecraft Environment Engineering). This paper describes the infrared lamp array simulation technology used for satellite thermal balance and thermal vacuum test. These tests were performed in KM6 space environmental simulator in Beijing, China. New software and hardware developed by BISEE, along with enhanced heat flux uniformity, provided for well accomplished thermal balance and thermal vacuum tests. The flux uniformity of lamp array was satisfied with test requirement. Monitored background radiometer offered reliable heat flux measurements with remarkable repeatability. Simulation software supplied accurate thermal flux distribution predictions.
Abstract: Knowledge of patterns of genetic diversity enhances
the efficiency of germplasm conservation and improvement. In this
study 96 Iranian landraces of Triticum turgidum originating from
different geographical areas of Iran, along with 18 durum cultivars
from ten countries were evaluated for variation in morphological and
high molecular weight glutenin subunit (HMW-GS) composition.
The first two principal components clearly separated the Iranian
landraces from cultivars. Three alleles were present at the Glu-A1
locus and 11 alleles at Glu-B1. In both cultivars and landraces of
durum wheat, the null allele (Glu-A1c) was observed more
frequently than the Glu-A1a and Glu-A1b alleles. Two alleles,
namely Glu-B1a (subunit 7) and Glu-B1e (subunit 20) represented
the more frequent alleles at Glu-B1 locus. The results showed that
the evaluated Iranian landraces formed an interesting source of
favourable glutenin subunits that might be very desirable in breeding
activities for improving pasta-making quality.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by a reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system using various refrigerants are limited to an evaporator
temperature of -40 0C. Below temperature of -40 0C the either
cascade refrigeration system or multi stage vapour compression
system is employed. Present work describes thermal design of
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser, cascade condenser and evaporator for
both systems are compared and the effect of condenser and
evaporator temperature on heat-transfer area for both systems is
studied under same operating condition. The results shows that the
required heat-transfer area of condenser and cascade condenser for
R410A-R23 cascade system is lower than the R404A-R508B cascade
system but heat transfer area of evaporator is similar for both the
system. The heat transfer area of condenser and cascade condenser
decreases with increase in condenser temperature (Tc), whereas the
heat transfer area of cascade condenser and evaporator increases with
increase in evaporator temperature (Te).