Abstract: This work presents the highly accurate numerical calculation
of the natural frequencies for functionally graded beams with
simply supported boundary conditions. The Timoshenko first order
shear deformation beam theory and the higher order shear deformation
beam theory of Reddy have been applied to the functionally
graded beams analysis. The material property gradient is assumed
to be in the thickness direction. The Hamilton-s principle is utilized
to obtain the dynamic equations of functionally graded beams. The
influences of the volume fraction index and thickness-to-length ratio
on the fundamental frequencies are discussed. Comparison of the
numerical results for the homogeneous beam with Euler-Bernoulli
beam theory results show that the derived model is satisfactory.
Abstract: Prestressing in structure increases ratio of load-bearing capacity to weight. Suspendomes are single-layer braced domes reinforced with cable and strut. Prestressing of cables alter value and distribution of stress in structure. In this study two configuration, diamatic and lamella domes is selected. Investigated domes have span of 100m with rise-to-span ratios of 0.1, 0.2, and 0.3. Single layer domes loaded under service load combinations according to ISO code. After geometric nonlinear analysis, models are designed with tubular and I-shaped sections then reinforced with cable and strut and converted to suspendomes. Displacements and stresses of some groups of nodes and elements in all of single-layer domes and suspendomes for three load combinations, symmetric snow, asymmetric snow and wind are compared. Variation due to suspending system is investigated. Suspendomes are redesigned and minimum possible weight after addition of cable and strut is obtained.
Abstract: This paper presents a numerical analysis of the
seismic behaviour of earth dams. Analysis is conducted for the solid
phase. It may correspond to the response of the dam before water
filling. Analysis is conducted for a simple case which concerns the
elastic response of the dam. Numerical analyses are conducted using
the FLAC3D program. The behaviour of the Shell and core of the
dam and the foundation behaviour is assumed to be elastic. Result
shows the influence of the variation of the shear modulus of the core
and shell on the seismic amplification of the dam. It can be observed
that the variation of the shearing modulus of the core leads to a
moderate increase in the dynamic amplification and the increase in
the shell shearing modulus leads to a significant increase in the
dynamic amplification.
Abstract: In this work the numerical simulation of transient heat
transfer in a cylindrical probe is done. An experiment was conducted
introducing a steel cylinder in a heating chamber and registering its
surface temperature along the time during one hour. In parallel, a
mathematical model was solved for one dimension transient heat
transfer in cylindrical coordinates, considering the boundary
conditions of the test. The model was solved using finite difference
method, because the thermal conductivity in the cylindrical steel bar
and the convection heat transfer coefficient used in the model are
considered temperature dependant functions, and both conditions
prevent the use of the analytical solution. The comparison between
theoretical and experimental results showed the average deviation is
below 2%. It was concluded that numerical methods are useful in
order to solve engineering complex problems. For constant k and h,
the experimental methodology used here can be used as a tool for
teaching heat transfer in mechanical engineering, using mathematical
simplified models with analytical solutions.
Abstract: This paper discusses coordinated reactive power -
voltage (Q-V) control in a multi machine steam power plant. The
drawbacks of manual Q-V control are briefly listed, and the design
requirements for coordinated Q-V controller are specified.
Theoretical background and mathematical model of the new
controller are presented next followed by validation of developed
Matlab/Simulink model through comparison with recorded
responses in real steam power plant and description of practical
realisation of the controller. Finally, the performance of
commissioned controller is illustrated on several examples of
coordinated Q-V control in real steam power plant and compared
with manual control.
Abstract: In this paper, verified extension of the Ostrowski method which calculates the enclosure solutions of a given nonlinear equation is introduced. Also, error analysis and convergence will be discussed. Some implemented examples with INTLAB are also included to illustrate the validity and applicability of the scheme.
Abstract: Many recent electrophysiological studies have
revealed the importance of investigating meditation state in order to
achieve an increased understanding of autonomous control of
cardiovascular functions. In this paper, we characterize heart rate
variability (HRV) time series acquired during meditation using
nonlinear dynamical parameters. We have computed minimum
embedding dimension (MED), correlation dimension (CD), largest
Lyapunov exponent (LLE), and nonlinearity scores (NLS) from HRV
time series of eight Chi and four Kundalini meditation practitioners.
The pre-meditation state has been used as a baseline (control) state to
compare the estimated parameters. The chaotic nature of HRV during
both pre-meditation and meditation is confirmed by MED. The
meditation state showed a significant decrease in the value of CD and
increase in the value of LLE of HRV, in comparison with premeditation
state, indicating a less complex and less predictable nature
of HRV. In addition, it was shown that the HRV of meditation state
is having highest NLS than pre-meditation state. The study indicated
highly nonlinear dynamic nature of cardiac states as revealed by
HRV during meditation state, rather considering it as a quiescent
state.
Abstract: Arrack is one of the forms of alcoholic beverage or
liquor which is produced from palm or date juice and commonly
consumed by the lower social class of all religious/ethnic
communities in the north-western villages of Bangladesh. The
purpose of the study was to compare arrack drinking patterns
associated with socio-demographic status among the Muslim, Hindu,
Santal, and Oraon communities in the Rasulpur union of Bangladesh.
A total of 391 respondents (Muslim n-109, Hindu n-103, Santal n-89,
Oraon n-90) selected by cluster random sampling were interviewed
by ADP (Arrack Drinking Pattern) questionnaire. The results of
Pearson Chi-Squire test revealed that arrack drinking patterns were
significantly differed among the Muslim, Hindu, Santal, and Oraon
communities- drinkers. In addition, the results of Spearman-s
bivariate correlation coefficients also revealed that sociodemographic
characteristics of the communities- drinkers were the
significantly positive and negative associations with the arrack
drinking patterns in the Rasulpur union, Bangladesh. The study
suggests that further cross-cultural researches should be conducted
on the consequences of arrack drinking patterns on the communities-
drinkers.
Abstract: The purpose of this study is to review representative
cases of green space development in order to compare the Garden City
concept and Green Belt concept as applied and to examine its direction
in major Asian and Oceanic cities. The results of previous studies and
this study show that there are two major directions in such
green-oriented city planning. One direction is toward Multi-Regional
Development, and the other focuses on an Environmentally Symbiotic
City based on the Garden City concept. In large cities and the suburbs
where extremely strong pressure to urbanize makes it impossible to
keep Green Belts, it is essential to strictly control land use and adopt
the Garden City concept to conserve the urban environment.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: Today modern simulations solutions in the wind turbine industry have achieved a high degree of complexity and detail in result. Limitations exist when it is time to validate model results against measurements. Regarding Model validation it is of special interest to identify mode frequencies and to differentiate them from the different excitations. A wind turbine is a complex device and measurements regarding any part of the assembly show a lot of noise. Input excitations are difficult or even impossible to measure due to the stochastic nature of the environment. Traditional techniques for frequency analysis or features extraction are widely used to analyze wind turbine sensor signals, but have several limitations specially attending to non stationary signals (Events). A new technique based on autoregresive analysis techniques is introduced here for a specific application, a comparison and examples related to different events in the wind turbine operations are presented.
Abstract: This paper presents a design method of self-tuning
Quantitative Feedback Theory (QFT) by using improved deadbeat
control algorithm. QFT is a technique to achieve robust control with
pre-defined specifications whereas deadbeat is an algorithm that
could bring the output to steady state with minimum step size.
Nevertheless, usually there are large peaks in the deadbeat response.
By integrating QFT specifications into deadbeat algorithm, the large
peaks could be tolerated. On the other hand, emerging QFT with
adaptive element will produce a robust controller with wider
coverage of uncertainty. By combining QFT-based deadbeat
algorithm and adaptive element, superior controller that is called selftuning
QFT-based deadbeat controller could be achieved. The output
response that is fast, robust and adaptive is expected. Using a grain
dryer plant model as a pilot case-study, the performance of the
proposed method has been evaluated and analyzed. Grain drying
process is very complex with highly nonlinear behaviour, long delay,
affected by environmental changes and affected by disturbances.
Performance comparisons have been performed between the
proposed self-tuning QFT-based deadbeat, standard QFT and
standard dead-beat controllers. The efficiency of the self-tuning QFTbased
dead-beat controller has been proven from the tests results in
terms of controller’s parameters are updated online, less percentage
of overshoot and settling time especially when there are variations in
the plant.
Abstract: This paper examines and compares several of the most common real time methods. These methods are CORE, YSM, MASCOT, JSD, DARTS, RTSAD, ADARTS, CODARTS, HOOD, HRT-HOOD, ROOM, UML, UML-RT. The methods are compared using attributes like i) usability, ii) compositionality and iii) proper RT notations available. Finally some comparison results are given and discussed.
Abstract: This paper describes new computer vision algorithms
that have been developed to track moving objects as part of a
long-term study into the design of (semi-)autonomous vehicles. We
present the results of a study to exploit variable kernels for tracking in
video sequences. The basis of our work is the mean shift
object-tracking algorithm; for a moving target, it is usual to define a
rectangular target window in an initial frame, and then process the data
within that window to separate the tracked object from the background
by the mean shift segmentation algorithm. Rather than use the
standard, Epanechnikov kernel, we have used a kernel weighted by the
Chamfer distance transform to improve the accuracy of target
representation and localization, minimising the distance between the
two distributions in RGB color space using the Bhattacharyya
coefficient. Experimental results show the improved tracking
capability and versatility of the algorithm in comparison with results
using the standard kernel. These algorithms are incorporated as part of
a robot test-bed architecture which has been used to demonstrate their
effectiveness.
Abstract: Bioinformatics and computational biology involve
the use of techniques including applied mathematics,
informatics, statistics, computer science, artificial intelligence,
chemistry, and biochemistry to solve biological problems
usually on the molecular level. Research in computational
biology often overlaps with systems biology. Major research
efforts in the field include sequence alignment, gene finding,
genome assembly, protein structure alignment, protein structure
prediction, prediction of gene expression and proteinprotein
interactions, and the modeling of evolution. Various
global rearrangements of permutations, such as reversals and
transpositions,have recently become of interest because of their
applications in computational molecular biology. A reversal is
an operation that reverses the order of a substring of a permutation.
A transposition is an operation that swaps two adjacent
substrings of a permutation. The problem of determining the
smallest number of reversals required to transform a given
permutation into the identity permutation is called sorting by
reversals. Similar problems can be defined for transpositions
and other global rearrangements. In this work we perform a
study about some genome rearrangement primitives. We show
how a genome is modelled by a permutation, introduce some
of the existing primitives and the lower and upper bounds
on them. We then provide a comparison of the introduced
primitives.
Abstract: Isobaric vapor-liquid equilibrium measurements are
reported for the binary mixture of Methyl acetate and
Isopropylbenzene at 97.3 kPa. The measurements have been
performed using a vapor recirculating type (modified Othmer's)
equilibrium still. The mixture shows positive deviation from ideality
and does not form an azeotrope. The activity coefficients have been
calculated taking into consideration the vapor phase nonideality. The
data satisfy the thermodynamic consistency tests of Herington and
Black. The activity coefficients have been satisfactorily correlated by
means of the Margules, NRTL, and Black equations. A comparison
of the values of activity coefficients obtained by experimental data
with the UNIFAC model has been made.
Abstract: Based on Traub-s methods for solving nonlinear
equation f(x) = 0, we develop two families of third-order
methods for solving system of nonlinear equations F(x) = 0. The
families include well-known existing methods as special cases.
The stability is corroborated by numerical results. Comparison
with well-known methods shows that the present methods are
robust. These higher order methods may be very useful in the
numerical applications requiring high precision in their computations
because these methods yield a clear reduction in number of iterations.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: An electronic portal image device (EPID) has become
a method of patient-specific IMRT dose verification for radiotherapy.
Research studies have focused on pre and post-treatment verification,
however, there are currently no interventional procedures using EPID
dosimetry that measure the dose in real time as a mechanism to
ensure that overdoses do not occur and underdoses are detected as
soon as is practically possible. As a result, an EPID-based real time
dose verification system for dynamic IMRT was developed and was
implemented with MATLAB/Simulink. The EPID image acquisition
was set to continuous acquisition mode at 1.4 images per second. The
system defined the time constraint gap, or execution gap at the image
acquisition time, so that every calculation must be completed before
the next image capture is completed. In addition, the