Abstract: Theoptimal extraction condition of dried Phaseolus
vulgaris powderwas studied. The three independent variables are raw
material concentration, shaking and centrifugaltime. The dependent
variables are both yield percentage of crude extract and alphaamylase
enzyme inhibition activity. The experimental design was
based on box-behnkendesign. Highest yield percentage of crude
extract could get from extraction condition at concentration of 1, 0,1,
concentration of 0.15 M ,extraction time for 2hour, and
separationtime for60 min. Moreover, the crude extract with highest
alpha-amylase enzyme inhibition activityoccurred by extraction
condition at concentration of 0.10 M, extraction time for 2 min, and
separation time for 45 min
Abstract: Offset Double-Disk Opener (DDO) is a popular
furrow opener in conservation tillage. It has some limitations such as
negative suction to penetrate in the soil, hair pinning and mixing seed
and fertilizer in the slot. Because of importance of separation of seed
and fertilizer in the slot, by adding two horizontal mini disks to DDO
a modified opener was made (MDO) which placed the fertilizer
between and under two rows of seed. To consider performance of
novel opener an indoor comparison test between DDO and MDO was
performed at soil bin. The experiment was conducted with three
working speeds (3, 6 and 8 km h-1), two bulk densities of soil (1.1
and 1.4 Mg m-3) and two levels of residues (1 and 2 ton ha-1). The
experimental design consisted in a (3×2×2) complete randomized
factorial with three replicates for each test. Moisture of seed furrow,
separation of seed and fertilizer, hair pinning and resultant forces
acting on the openers were used as assessing indexes. There was no
significant difference between soil moisture content in slots created
by DDO and MDO at 0-4 cm depth, but at 4-8 cm the in the slot
created by MDO moisture content was higher about 9%. Horizontal
force for both openers increased with increasing speed and soil bulk
density. Vertical force for DDO was negative so it needed additional
weight for penetrating in the soil, but vertical force for MDO was
positive and, which can solve the challenge of penetration in the soil
in DDO. In soft soil with heavy residues some trash was pushed by
DDO into seed furrow (hair pinning) but at MDO seed were placed at
clean groove. Lateral and vertical separation of seed and fertilizer
was performed effectively by MDO (4.5 and 5 cm, respectively)
while DDO put seed and fertilizer close to each other. Overall, the
Modified Offset Double-disks (MDO) had better performance. So by
adapting this opener with no-tillage drillers it would possible to have
higher yield in conservation tillage where the most appropriate
opener is disk type.
Abstract: Brassinosteroids (BRs) regulate cell elongation,
vascular differentiation, senescence, and stress responses. BRs signal
through the BES1/BZR1 family of transcription factors, which
regulate hundreds of target genes involved in this pathway. In this
research a comprehensive genome-wide analysis was carried out in
BES1/BZR1 gene family in Arabidopsis thaliana, Cucumis sativus,
Vitis vinifera, Glycin max and Brachypodium distachyon.
Specifications of the desired sequences, dot plot and hydropathy plot
were analyzed in the protein and genome sequences of five plant
species. The maximum amino acid length was attributed to protein
sequence Brdic3g with 374aa and the minimum amino acid length
was attributed to protein sequence Gm7g with 163aa. The maximum
Instability index was attributed to protein sequence AT1G19350
equal with 79.99 and the minimum Instability index was attributed to
protein sequence Gm5g equal with 33.22. Aliphatic index of these
protein sequences ranged from 47.82 to 78.79 in Arabidopsis
thaliana, 49.91 to 57.50 in Vitis vinifera, 55.09 to 82.43 in Glycin
max, 54.09 to 54.28 in Brachypodium distachyon 55.36 to 56.83 in
Cucumis sativus. Overall, data obtained from our investigation
contributes a better understanding of the complexity of the
BES1/BZR1 gene family and provides the first step towards directing
future experimental designs to perform systematic analysis of the
functions of the BES1/BZR1 gene family.
Abstract: The assessment of the efficacy of devised Mobile-
Assisted Instructional Modes in Mobile Learning was the focus of
this research. The study adopted pre-test, post-test, control group
quasi-experimental design. Research instruments were developed,
validated and used for collecting data. Findings revealed that the
students exposed to Mobile Task Based Learning Mode (MTBLM) in
using Mobile-Assisted Instruction (MAI) performed significantly
better. The implication of these findings is that, the Audio tutorial
and Practice Mode (ATPM) (Stimulus instruments) of MAI had been
found better over the other modes used in the study.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: An experiment was conducted to study the effects of different types of probiotic on Sucrase enzyme activity of the small intestine mucosa in male broilers. The experimental design was arranged as randomized completely blocks in 4 × 2 factorial arrangement of treatment. 180 male broilers of Ross 308 commercial hybrid were designated into 4 groups. Three replicates of 15 birds were assigned to each treatment. Control treatments (diet contained no probiotic) were fed according to the NRC as base diet and three treatment groups were fed from the same diet plus three different types of probiotics. Birds were slaughtered after 21 and 42 days and different segments of small intestine (at 1,10,30,50,70 and 90% of total length the small intestine) were taken from each replicates (N=2) Sucrase enzyme activities were measured and recorded. Obtained data were analyzed by Spss (P
Abstract: The purpose of this study is to investigate the effects
of modality principles in instructional software among first grade
pupils- achievements in the learning of Arabic Language. Two modes
of instructional software were systematically designed and
developed, audio with images (AI), and text with images (TI). The
quasi-experimental design was used in the study. The sample
consisted of 123 male and female pupils from IRBED Education
Directorate, Jordan. The pupils were randomly assigned to any one of
the two modes. The independent variable comprised the two modes
of the instructional software, the students- achievement levels in the
Arabic Language class and gender. The dependent variable was the
achievements of the pupils in the Arabic Language test. The
theoretical framework of this study was based on Mayer-s Cognitive
Theory of Multimedia Learning. Four hypotheses were postulated
and tested. Analyses of Variance (ANOVA) showed that pupils using
the (AI) mode performed significantly better than those using (TI)
mode. This study concluded that the audio with images mode was an
important aid to learning as compared to text with images mode.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: This research adapts experimental design to investigate
the effect of conditioning or not and pre-exposure or not on brand
attitude, so it is a 2×2=4 factorial design. The results show that the
brand attitude of conditioning group is significantly higher than that of
unconditioning group. The brand attitude with pre-exposure is
significantly higher than that without pre-exposure. Conditioning or
not and pre-exposure or not have significant interaction. No matter the
celebrity is pre-exposure or not, the brand attitude is higher under
conditioning process.
Abstract: Response surface methodology was used for
quantitative investigation of water and solids transfer during osmotic
dehydration of beetroot in aqueous solution of salt. Effects of
temperature (25 – 45oC), processing time (30–150 min), salt
concentration (5–25%, w/w) and solution to sample ratio (5:1 – 25:1)
on osmotic dehydration of beetroot were estimated. Quadratic
regression equations describing the effects of these factors on the
water loss and solids gain were developed. It was found that effects
of temperature and salt concentrations were more significant on the
water loss than the effects of processing time and solution to sample
ratio. As for solids gain processing time and salt concentration were
the most significant factors. The osmotic dehydration process was
optimized for water loss, solute gain, and weight reduction. The
optimum conditions were found to be: temperature – 35oC,
processing time – 90 min, salt concentration – 14.31% and solution
to sample ratio 8.5:1. At these optimum values, water loss, solid gain
and weight reduction were found to be 30.86 (g/100 g initial sample),
9.43 (g/100 g initial sample) and 21.43 (g/100 g initial sample)
respectively.
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: Heavy metal pollution is an environmental concern.
Phytoremediation is a low-cost, environmental-friendly approach to
solve this problem. Mustard has the potential in reducing heavy metal
contents in soils. Among mustard (Brassica juncea (L.) Czern &
Coss) genotypes in Sri Lanka, accessions 7788, 8831 and 5088 give
significantly a high yield. Therefore, present study was conducted to
quantify the phytoextractive potential among these local mustard
accessions and to assess the interaction of heavy metals, Pb, Co, Mn
on phytoextraction. A pot experiment was designed with acid washed
sand (quartz) and a series of heavy metal solutions of 0, 25, 50, 75
and 100 μg/g. Experiment was carried out with factorial
experimental design. Mustard accessions were tolerant to heavy
metals and could be successfully used in removal of Pb, Co and Mn
and they are capable of accumulating significant quantities of heavy
metals in vegetative and reproductive organs. The order of the
accumulative potential of Pb, Co and Mn in mustard accessions is,
root > shoot >seed.
Abstract: The effect of phosphorus supplementation of ammoniated rice straw was studied. The in vitro experiment was carried out following the first stage of Tilley and Terry method. The treatments consisting of four diets were A = 50% ammoniated rice straw + 50% concentrate (control), B = A + 0.2% Phosphor (P) supplement, C = A + 0.4% Phosphor (P) supplement, and D = A + 0.6% Phosphor (P) supplement of dry matter. Completely randomized design was used as the experimental design with differences among treatment means were examined using Duncan multiple range test. Variables measured were total bacterial and cellulolytic bacterial population, cellulolytic enzyme activity, ammonia (NH3) and volatile fatty acid (VFA) concentrations, as fermentability indicators and synthesized microbial protein, as well as degradability indicators including dry matter (DM), organic matter (OM), neutral detergent fibre (NDF), acid detergent fibre (ADF) and cellulose. The results indicated that fermentability and degradability of diets consisting ammoniated rice straw with P supplementation were significantly higher than the control diet (P< 0.05). It is concluded that P supplementation is important to improve fermentability and degradability of rations containing ammoniated RS and concentrate. In terms of the most effective level of P supplementation occurred at a supplementation rate of 0.4% of dry matter.
Abstract: The purpose of this study is to discuss the effect of the
intervention of exercise behavior change plan for high school students
on study subjects- social and psychological factors and exercise
stages. This research uses the transtheoretical model as the research
framework. One experiment group and one control group were used in
a quasi-experimental design research. The experimental group
accepted health-related physical fitness course and the traditional
course; the control group accepted traditional physical education
course. There is a significant difference before and after the
intervention in the experimental group. Karl-s test shows the
experimental group gained a better improvement than that in the
control group. The Analysis of Covariance had shown the exercise
stages (F=7.62, p
Abstract: Direct fermentation of 226 white rose tapioca stem to
ethanol by Fusarium oxysporum was studied in a batch reactor.
Fermentation of ethanol can be achieved by sequential pretreatment
using dilute acid and dilute alkali solutions using 100 mesh tapioca
stem particles. The quantitative effects of substrate concentration, pH
and temperature on ethanol concentration were optimized using a full
factorial central composite design experiment. The optimum process
conditions were then obtained using response surface methodology.
The quadratic model indicated that substrate concentration of 33g/l,
pH 5.52 and a temperature of 30.13oC were found to be optimum for
maximum ethanol concentration of 8.64g/l. The predicted optimum
process conditions obtained using response surface methodology was
verified through confirmatory experiments. Leudeking-piret model
was used to study the product formation kinetics for the production
of ethanol and the model parameters were evaluated using
experimental data.
Abstract: In this work, statistical experimental design was
applied for the optimization of medium constituents for Gentamicin
production by Micromsonospora echinospora subs pallida (MTCC
708) in a batch reactor and the results are compared with the ANN
predicted values. By central composite design, 50 experiments are
carried out for five test variables: Starch, Soya bean meal, K2HPO4,
CaCO3 and FeSO4. The optimum condition was found to be: Starch
(8.9,g/L), Soya bean meal (3.3 g/L), K2HPO4 (0.8 g/L), CaCO3 (4
g/L) and FeSO4 (0.03 g/L). At these optimized conditions, the yield
of gentamicin was found to be 1020 mg/L. The R2 values were found
to be 1 for ANN training set, 0.9953 for ANN test set, and 0.9286 for
RSM.
Abstract: carbonylation of methanol in homogenous phase is
one of the major routesfor production of acetic acid. Amongst group
VIII metal catalysts used in this process iridium has displayed the
best capabilities. To investigate effect of operating parameters like:
temperature, pressure, methyl iodide, methyl acetate, iridium,
ruthenium, and water concentrations on the reaction rate,
experimental design for this system based upon central composite
design (CCD) was utilized. Statistical rate equation developed by this
method contained individual, interactions and curvature effects of
parameters on the reaction rate. The model with p-value less than
0.0001 and R2 values greater than 0.9; confirmeda satisfactory fitness
of the experimental and theoretical studies. In other words, the
developed model and experimental data obtained passed all
diagnostic tests establishing this model as a statistically significant.
Abstract: The spatial variation in plant species associated with intercropping is intended to reduce resource competition between species and increase yield potential. A field experiment was carried out on corn (Zea mays L.) and soybean (Glycine max L.) intercropping in a replacement series experiment with weed contamination consist of: weed free, infestation of redroot pigweed, infestation of jimsonweed and simultaneous infestation of redroot pigweed and jimsonweed in Karaj, Iran during 2007 growing season. The experimental design was a randomized complete block in factorial experiment with replicated thrice. Significant (P≤0.05) differences were observed in yield in intercropping. Corn yield was higher in intercropping, but soybean yield was significantly reduced by corn when intercropped. However, total productivity and land use efficiency were high under the intercropping system even in contamination of either species of weeds. Aggressivity of corn relative to soybean revealed the greater competitive ability of corn than soybean. Land equivalent ratio (LER) more than 1 in all treatments attributed to intercropping advantages and was highest in 50: 50 (corn/soybean) in weed free. These findings suggest that intercropping corn and soybean increase total productivity per unit area and improve land use efficiency. Considering the experimental findings, corn-soybean intercropping (50:50) may be recommended for yield advantage, more efficient utilization of resources, and weed suppression as a biological control.
Abstract: The aim of this study was to compare the solubility of selected volatile organic compounds in water and silicon oil using the simple static headspace method. The experimental design allowed equilibrium achievement within 30 – 60 minutes. Infinite dilution activity coefficients and Henry-s law constants for various organics representing esters, ketones, alkanes, aromatics, cycloalkanes and amines were measured at 303K. The measurements were reproducible with a relative standard deviation and coefficient of variation of 1.3x10-3 and 1.3 respectively. The static determined activity coefficients using shaker flasks were reasonably comparable to those obtained using the gas liquid - chromatographic technique and those predicted using the group contribution methods mainly the UNIFAC. Silicon oil chemically known as polydimethysiloxane was found to be better absorbent for VOCs than water which quickly becomes saturated. For example the infinite dilution mole fraction based activity coefficients of hexane is 0.503 and 277 000 in silicon oil and water respectively. Thus silicon oil gives a superior factor of 550 696. Henry-s law constants and activity coefficients at infinite dilution play a significant role in the design of scrubbers for abatement of volatile organic compounds from contaminated air streams. This paper presents the phase equilibrium of volatile organic compounds in very dilute aqueous and polymeric solutions indicating the movement and fate of chemical in air and solvent. The successful comparison of the results obtained here and those obtained using other methods by the same authors and in literature, means that the results obtained here are reliable.
Abstract: In this paper we investigate the influence of external
noise on the inference of network structures. The purpose of our
simulations is to gain insights in the experimental design of microarray
experiments to infer, e.g., transcription regulatory networks
from microarray experiments. Here external noise means, that the
dynamics of the system under investigation, e.g., temporal changes of
mRNA concentration, is affected by measurement errors. Additionally
to external noise another problem occurs in the context of microarray
experiments. Practically, it is not possible to monitor the mRNA
concentration over an arbitrary long time period as demanded by the
statistical methods used to learn the underlying network structure. For
this reason, we use only short time series to make our simulations
more biologically plausible.