Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.
Abstract: An experiment was conducted using two aeration
methods (water-into-air and air-into-water) and followed by filtration
processes using manganese greensand material. The properties of
groundwater such as pH, dissolved oxygen, turbidity and heavy metal
concentration (iron and manganese) will be assessed. The objectives
of this study are i) to determine the effective aeration method and ii)
to assess the effectiveness of manganese greensand as filter media in
removing iron and manganese concentration in groundwater. Results
showed that final pH for all samples after treatment are in range from
7.40 and 8.40. Both aeration methods increased the dissolved oxygen
content. Final turbidity for groundwater samples are between 3 NTU
to 29 NTU. Only three out of eight samples achieved iron
concentration of 0.3mg/L and less and all samples reach manganese
concentration of 0.1mg/L and less. Air-into-water aeration method
gives higher percentage of iron and manganese removal compare to
water-into-air method.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: The process of laser absorption in the skin during
laser irradiation was a critical point in medical application
treatments. Delivery the correct amount of laser light is a critical
element in photodynamic therapy (PDT). More amounts of laser
light able to affect tissues in the skin and small amount not able to
enhance PDT procedure in skin. The knowledge of the skin tone
laser dependent distribution of 635 nm radiation and its penetration
depth in skin is a very important precondition for the investigation of
advantage laser induced effect in (PDT) in epidermis diseases
(psoriasis). The aim of this work was to estimate an optimum effect
of diode laser (635 nm) on the treatment of epidermis diseases in
different color skin. Furthermore, it is to improve safety of laser in
PDT in epidermis diseases treatment. Advanced system analytical
program (ASAP) which is a new approach in investigating the PDT,
dependent on optical properties of different skin color was used in
present work. A two layered Realistic Skin Model (RSM); stratum
corneum and epidermal with red laser (635 nm, 10 mW) were used
for irradiative transfer to study fluence and absorbance in different
penetration for various human skin colors. Several skin tones very
fair, fair, light, medium and dark are used to irradiative transfer. This
investigation involved the principles of laser tissue interaction when
the skin optically injected by a red laser diode. The results
demonstrated that the power characteristic of a laser diode (635 nm)
can affect the treatment of epidermal disease in various color skins.
Power absorption of the various human skins were recorded and
analyzed in order to find the influence of the melanin in PDT
treatment in epidermal disease. A two layered RSM show that the
change in penetration depth in epidermal layer of the color skin has a
larger effect on the distribution of absorbed laser in the skin; this is
due to the variation of the melanin concentration for each color.
Abstract: Green propellants used for satellite-level propulsion
system become attractive in recent years because the non-toxicity and
lower requirements of safety protection. One of the green propellants,
high-concentration hydrogen peroxide H2O2 solution (≥70% w/w,
weight concentration percentage), often known as high-test peroxide
(HTP), is considered because it is ITAR-free, easy to manufacture and
the operating temperature is lower than traditional monopropellant
propulsion. To establish satellite propulsion technology, the National
Space Organization (NSPO) in Taiwan has initialized a long-term
cooperation project with the National Cheng Kung University to
develop compatible tank and thruster. An experimental propulsion
payload has been allocated for the future self-reliant satellite to
perform orbit transfer and maintenance operations. In the present
research, an 1-Newton thruster prototype is designed and the thrusting
force is measured by a pendulum-type platform. The preliminary
hot-firing test at ambient environment showed the generated thrust and
the specific impulse are about 0.7 Newton and 102 seconds,
respectively.
Abstract: In this study, the ability of Aspergillus niger and
Penicillium simplicissimum to extract heavy metals from a spent
refinery catalyst was investigated. For the first step, a spent
processing catalyst from one of the oil refineries in Iran was
physically and chemically characterized. Aspergillus niger and
Penicillium simplicissimum were used to mobilize Al/Co/Mo/Ni from
hazardous spent catalysts. The fungi were adapted to the mixture of
metals at 100-800 mg L-1 with increments in concentration of 100 mg
L-1. Bioleaching experiments were carried out in batch cultures. To
investigate the production of organic acids in sucrose medium,
analyses of the culture medium by HPLC were performed at specific
time intervals after inoculation. The results obtained from Inductive
coupled plasma-optical emission spectrometry (ICP-OES) showed
that after the one-step bioleaching process using Aspergillus niger,
maximum removal efficiencies of 27%, 66%, 62% and 38% were
achieved for Al, Co, Mo and Ni, respectively. However, the highest
removal efficiencies using Penicillium simplicissimum were of 32%,
67%, 65% and 38% for Al, Co, Mo and Ni, respectively
Abstract: Obesity is frequent attendant phenomenon of patients
with endocrinological disease. Between BMI and endocrinological
diseases is close correlation. In thesis we focused on the allocation of
hormone concentration – PTH and TSH, CHOL a mineral element Ca
in a blood serum. The examined group was formed by 100
respondents (women) aged 36 – 83 years, who were divided into two
groups – control group (CG), group with diagnosed endocrine disease
(DED). The concentration of PTH and TSH, Ca and CHOL was
measured through the medium of analyzers Cobas e411 (Japan);
Cobas Integra 400 (Switzerland). At individuals was measured body
weight as well as stature and thereupon from those data we
enumerated BMI. On the basis of Student T-test in biochemical
parameter of PTH and Ca we found out significantly meaningful
difference (p
Abstract: This study has applied the L16 orthogonal array of the
Taguchi method to determine the optimized polymeric
Nanocomposite asphalt binder. Three control factors are defined as
polypropylene plastomer (PP), styrene-butadiene-styrene elastomer
(SBS) and Nanoclay. Four level of concentration contents are
introduced for prepared asphalt binder samples. all samples were
prepared with 4.5% of bitumen 60/70 content. Compressive strength
tests were carried out for defining the optimized sample via
QUALITEK-4 software. SBS with 3%, PP with 5 % and Nanoclay
with 1.5% of concentrations are defined as the optimized
Nanocomposite asphalt binders. The confirmation compressive
strength and also softening point tests showed that modification of
asphalt binders with this method, improved the compressive strength
and softening points of asphalt binders up to 55%.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: A research project dealing with the phytoremediation
of a soil polluted by some heavy metals is currently running. The
case study is represented by a mining area in Hamedan province in
the central west part of Iran. The potential of phytoextraction and
phytostabilization of plants was evaluated considering the
concentration of heavy metals in the plant tissues and also the
bioconcentration factor (BCF) and the translocation factor (TF). Also
the several established criteria were applied to define
hyperaccumulator plants in the studied area. Results showed that
none of the collected plant species were suitable for phytoextraction
of Cu, Zn, Fe and Mn, but among the plants, Euphorbia macroclada
was the most efficient in phytostabilization of Cu and Fe, while,
Ziziphora clinopodioides, Cousinia sp. and Chenopodium botrys
were the most suitable for phytostabilization of Zn and Chondrila
juncea and Stipa barbata had the potential for phytostabilization of
Mn. Using the most common criterion, Euphorbia macroclada and
Verbascum speciosum were Fe hyperaccumulator plants. Present
study showed that native plant species growing on contaminated sites
may have the potential for phytoremediation.
Abstract: In the present paper, a set of parametric FE stress
analyses is carried out for two-planar welded tubular DKT-joints
under two different axial load cases. Analysis results are used to
present general remarks on the effect of geometrical parameters on
the stress concentration factors (SCFs) at the inner saddle, outer
saddle, toe, and heel positions on the main (outer) brace. Then a new
set of SCF parametric equations is developed through nonlinear
regression analysis for the fatigue design of two-planar DKT-joints.
An assessment study of these equations is conducted against the
experimental data; and the satisfaction of the criteria regarding the
acceptance of parametric equations is checked. Significant effort has
been devoted by researchers to the study of SCFs in various uniplanar
tubular connections. Nevertheless, for multi-planar joints
covering the majority of practical applications, very few
investigations have been reported due to the complexity and high
cost involved.
Abstract: The effect of the number of quantum dot (QD) layers
on the saturated gain of doped QD semiconductor optical amplifiers
(SOAs) has been studied using multi-population coupled rate
equations. The developed model takes into account the effect of
carrier coupling between adjacent layers. It has been found that
increasing the number of QD layers (K) increases the unsaturated
optical gain for K
Abstract: Soil organic carbon (SOC) plays a key role in soil
fertility, hydrology, contaminants control and acts as a sink or source
of terrestrial carbon content that can affect the concentration of
atmospheric CO2. SOC supports the sustainability and quality of
ecosystems, especially in semi-arid region. This study was
conducted to determine relative importance of 13 different
exploratory climatic, soil and geometric factors on the SOC contents
in one of the semiarid watershed zones in Iran. Two methods
canonical discriminate analysis (CDA) and feed-forward back
propagation neural networks were used to predict SOC. Stepwise
regression and sensitivity analysis were performed to identify
relative importance of exploratory variables. Results from sensitivity
analysis showed that 7-2-1 neural networks and 5 inputs in CDA
models output have highest predictive ability that explains %70 and
%65 of SOC variability. Since neural network models outperformed
CDA model, it should be preferred for estimating SOC.
Abstract: The purpose of this research is to reduce the amount of incomplete coating of stainless steel washers in the electrodeposition painting process by using an experimental design technique. The surface preparation was found to be a major cause of painted surface quality. The influence of pretreating and painting process parameters, which are cleaning time, chemical concentration and shape of hanger were studied. A 23 factorial design with two replications was performed. The analysis of variance for the designed experiment showed the great influence of cleaning time and shape of hanger. From this study, optimized cleaning time was determined and a newly designed electrical conductive hanger was proved to be superior to the original one. The experimental verification results showed that the amount of incomplete coating defects decreased from 4% to 1.02% and operation cost decreased by 10.5%.
Abstract: Biological treatment of secondary effluent wastewater
by two combined denitrification/oxic filtration systems packed with
Lock type(denitrification filter) and ceramic ball (oxic filter) has been
studied for 5months. Two phases of operating conditions were carried
out with an influent nitrate and ammonia concentrations varied from
5.8 to 11.7mg/L and 5.4 to 12.4mg/L,respectively.
Denitrification/oxic filter treatment system were operated under an
EBCT (Empty Bed Contact Time) of 4h at system recirculation ratio in
the range from 0 to 300% (Linear Velocity increased 19.5m/d to
78m/d). The system efficiency of denitrification , nitrification over
95% respectively. Total nitrogen and COD removal range from
54.6%(recirculation 0%) to 92.3%(recirculation 300%) and 10% to
62.5%, respectively.
Abstract: A scaffold is necessary for tooth regeneration because of its three-dimensional geometry. For restoration of defect, it is necessary for the scaffold to be prepared in the shape of the defect. Sponges made from polyvinyl alcohol with formalin cross-linking (PVF sponge) have been used for scaffolds for bone formation in vivo. To induce osteogenesis within the sponge, methods of growing rat bone marrow cells (rBMCs) among the fiber structures in the sponge might be considered. Storage of rBMCs among the fibers in the sponge coated with dextran (10 kDa) was tried. After seeding of rBMCs to PVF sponge immersed in dextran solution at 2 g/dl concentration, osteogenesis was recognized in subcutaneously implanted PVF sponge as a scaffold in vivo. The level of osteocalcin was 25.28±5.71 ng/scaffold and that of Ca was 129.20±19.69 µg/scaffold. These values were significantly higher than those in sponges without dextran coating (p
Abstract: Removal of PCP by a system combining
biodegradation by biofilm and adsorption was investigated here.
Three studies were conducted employing batch tests, sequencing
batch reactor (SBR) and continuous biofilm activated carbon
column reactor (BACCOR). The combination of biofilm-GAC
batch process removed about 30% more PCP than GAC adsorption
alone. For the SBR processes, both the suspended and attached
biomass could remove more than 90% of the PCP after
acclimatisation. BACCOR was able to remove more than 98% of
PCP-Na at concentrations ranging from 10 to 100 mg/L, at empty
bed contact time (EBCT) ranging from 0.75 to 4 hours. Pure and
mixed cultures from BACCOR were tested for use of PCP as sole
carbon and energy source under aerobic conditions. The isolates
were able to degrade up to 42% of PCP under aerobic conditions in
pure cultures. However, mixed cultures were found able to degrade
more than 99% PCP indicating interdependence of species.
Abstract: Sulphur dioxide is a harmful gaseous product that
needs to be minimized in the atmosphere. This research work
investigates the use of zeolite as a possible additive that can improve
the sulphur dioxide capture in wet flue gas desulphurisation
dissolution process. This work determines the effect of temperature,
solid to liquid ratio, acid concentration and stirring speed on the
leaching of zeolite using a pH stat apparatus. The atomic absorption
spectrometer was used to measure the calcium ions from the solution.
It was found that the dissolution rate of zeolite decreased with
increase in solid to liquid ratio and increases with increase in
temperature, stirring speed and acid concentration. The activation
energy for the dissolution rate of zeolite in hydrochloric acid was
found to be 9.29kJ/mol. and therefore the product layer diffusion was
the rate limiting step.