Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: Requirement engineering has been the subject of large
volume of researches due to the significant role it plays in the
software development life cycle. However, dynamicity of software
industry is much faster than advances in requirements engineering
approaches. Therefore, this paper aims to systematically review and
evaluate the current research in requirement engineering and identify
new research trends and direction in this field. In addition, various
research methods associated with the Evaluation-based techniques
and empirical study are highlighted for the requirements engineering
field. Finally, challenges and recommendations on future directions
research are presented based on the research team observations
during this study.
Abstract: With the necessity of increased processing capacity with less energy consumption; power aware multiprocessor system has gained more attention in the recent future. One of the additional challenges that is to be solved in a multi-processor system when compared to uni-processor system is job allocation. This paper presents a novel task dependent job allocation algorithm: Energy centric- Allocation (Ec-A) and Rate Monotonic (RM) scheduling to minimize energy consumption in a multiprocessor system. A simulation analysis is carried out to verify the performance increase with reduction in energy consumption and required number of processors in the system.
Abstract: This paper deals with efficient computation of
probability coefficients which offers computational simplicity as
compared to spectral coefficients. It eliminates the need of inner
product evaluations in determination of signature of a combinational
circuit realizing given Boolean function. The method for computation
of probability coefficients using transform matrix, fast transform
method and using BDD is given. Theoretical relations for achievable
computational advantage in terms of required additions in computing
all 2n probability coefficients of n variable function have been
developed. It is shown that for n ≥ 5, only 50% additions are needed
to compute all probability coefficients as compared to spectral
coefficients. The fault detection techniques based on spectral
signature can be used with probability signature also to offer
computational advantage.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: We present a dual-band (Cellular & PCS) dual-path
zero-IF receiver for CDMA2000 diversity, monitoring and
simultaneous-GPS. The secondary path is a SAW-less diversity
CDMA receiver which can be also used for advanced features like
monitoring when supported with an additional external VCO. A GPS
receiver is integrated with its dedicated VCO allowing simultaneous
positioning during a cellular call. The circuit is implemented in a
0.25μm 40GHz-fT BiCMOS process and uses a HVQFN 56-pin
package. It consumes a maximum 300mW from a 2.8V supply in
dual-modes. The chip area is 12.8mm2.
Abstract: An adaptive Fuzzy Inference Perceptual model has
been proposed for watermarking of digital images. The model
depends on the human visual characteristics of image sub-regions in
the frequency multi-resolution wavelet domain. In the proposed
model, a multi-variable fuzzy based architecture has been designed to
produce a perceptual membership degree for both candidate
embedding sub-regions and strength watermark embedding factor.
Different sizes of benchmark images with different sizes of
watermarks have been applied on the model. Several experimental
attacks have been applied such as JPEG compression, noises and
rotation, to ensure the robustness of the scheme. In addition, the
model has been compared with different watermarking schemes. The
proposed model showed its robustness to attacks and at the same time
achieved a high level of imperceptibility.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: Numerical studies have been carried out using a two
dimensional code to examine the influence of pressure / thrust
transient of solid propellant rockets at liftoff. This code solves
unsteady Reynolds-averaged thin-layer Navier–Stokes equations by
an implicit LU-factorization time-integration method. The results
from the parametric study indicate that when the port is narrow there
is a possibility of increase in pressure / thrust-rise rate due to
relatively high flame spread rate. Parametric studies further reveal
that flame spread rate can be altered by altering the propellant
properties, igniter jet characteristics and nozzle closure burst pressure
without altering the grain configuration and/or the mission
demanding thrust transient. We observed that when the igniter
turbulent intensity is relatively low the vehicle could liftoff early due
to the early flow choking of the rocket nozzle. We concluded that the
high pressurization-rate has structural implications at liftoff in
addition to transient burning effect. Therefore prudent selection of the
port geometry and the igniter, for meeting the mission requirements,
within the given envelop are meaningful objectives for any designer
for the smooth liftoff of solid propellant rockets.
Abstract: The cumulative conformance count (CCC) charts are
widespread in process monitoring of high-yield manufacturing.
Recently, it is found the use of variable sampling interval (VSI)
scheme could further enhance the efficiency of the standard CCC
charts. The average time to signal (ATS) a shift in defect rate has
become traditional measure of efficiency of a chart with the VSI
scheme. Determining the ATS is frequently a difficult and tedious
task. A simple method based on a finite Markov Chain approach for
modeling the ATS is developed. In addition, numerical results are
given.
Abstract: Waste problem is becoming a future problem all over the world. Magnesium wastes which can be used in recycling processes are produced by many industrial activities. Magnesium borates which have useful properties such as; high heat resistance, corrosion resistance, supermechanical strength, superinsulation, light weight, high coefficient of elasticity and so on. Addition, magnesium borates have great potential in the development of ceramic and detergents industry, whisker-reinforced composites, antiwear, and reducing friction additives.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate temperature of 70oC with different reaction times. Several reaction times of waste magnesium to H3BO3 were selected as; 30, 60, 120, 240 minutes. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques were applied to products. As a result, the forms of Admontite [MgO(B2O3)3.7(H2O)] and Mcallisterite [Mg2(B6O7(OH)6)2.9(H2O)] were synthesized.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: The genetic algorithm (GA) based solution techniques
are found suitable for optimization because of their ability of
simultaneous multidimensional search. Many GA-variants have been
tried in the past to solve optimal power flow (OPF), one of the
nonlinear problems of electric power system. The issues like
convergence speed and accuracy of the optimal solution obtained
after number of generations using GA techniques and handling
system constraints in OPF are subjects of discussion. The results
obtained for GA-Fuzzy OPF on various power systems have shown
faster convergence and lesser generation costs as compared to other
approaches. This paper presents an enhanced GA-Fuzzy OPF (EGAOPF)
using penalty factors to handle line flow constraints and load
bus voltage limits for both normal network and contingency case
with congestion. In addition to crossover and mutation rate
adaptation scheme that adapts crossover and mutation probabilities
for each generation based on fitness values of previous generations, a
block swap operator is also incorporated in proposed EGA-OPF. The
line flow limits and load bus voltage magnitude limits are handled by
incorporating line overflow and load voltage penalty factors
respectively in each chromosome fitness function. The effects of
different penalty factors settings are also analyzed under contingent
state.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of sensitivity analysis on port operation quantity provide useful information for managers to choose the best scenario for port planning with the lowest investment risks. Despite all limitations-due to data availability-the model offers a straightforward decision tools to port planners aspiring to achieve optimum port planning steps.
Abstract: Due to urbanization, trees and plants which covered a great land mass of the earth and are an excellent carbon dioxide (CO2) absorber through photosynthesis are being replaced by several concrete based structures. It is therefore important to have these cement based structures absorb the large volume of carbon dioxide which the trees would have removed from the atmosphere during their useful lifespan. Hence the need for these cement based structures to be designed to serve other useful purposes in addition to shelter. This paper reviews the properties of Sodium carbonate and sugar as admixtures in concrete with respect to improving carbon sequestration in concrete.