Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: An optimal control strategy based on simple model, a
single phase unity power factor boost converter is presented with an
evaluation of first order differential equations. This paper presents an
evaluation of single phase boost converter having power factor
correction. The simple discrete model of boost converter is formed
and optimal control is obtained, digital PI is adopted to adjust control
error. The method of instantaneous current control is proposed in this
paper for its good tracking performance of dynamic response. The
simulation and experimental results verified our design.
Abstract: Dissolved gas analysis has been accepted as a sensitive, informative and reliable technique for incipient faults detection in power transformers and is widely used. In the last few years this method, which has been recommended by IEEE Power & Energy society, has been applied for fault detection in load tap changers. Regarding the critical role of load tap changers in electrical network and essential of catastrophic failures prevention, it is necessary to choose "condition based preventative maintenance strategy" which leads to reduction in costs, the number of unnecessary visits as well as the probability of interruptions and also increment in equipment reliability. In current work, considering the condition based preventative maintenance strategy, condition assessment of an Elin tap changer was carried out using dissolved gas analysis.
Abstract: In Egypt, the concept of Asset Management (AM) is
new; however, the need for applying it has become crucial because
deteriorating or losing an asset is unaffordable in a developing
country like Egypt. Therefore the current study focuses on
educational buildings as one of the most important assets regarding
planning, building, operating and maintenance expenditures. The
main objective of this study is to develop a SAMF for educational
buildings in Egypt. The General Authority for Educational Buildings
(GAEB) was chosen as a case study of the current research as it
represents the biggest governmental organization responsible for
planning, operating and maintaining schools in Egypt. To achieve the
research objective, structured interviews were conducted with senior
managers of GAEB using a pre designed questionnaire to explore the
current practice of AM. Gab analysis technique was applied against
best practices compounded from a vast literature review to identify
gaps between current practices and the desired one. The previous
steps mainly revealed; limited knowledge about strategic asset
management, no clear goals, no training, no real risk plan and lack of
data, technical and financial resources. Based on the findings, a
SAMF for GAEB was introduced and Framework implementation
steps and assessment techniques were explained in detail.
Abstract: Current advancements in nanotechnology are dependent
on the capabilities that can enable nano-scientists to extend their eyes
and hands into the nano-world. For this purpose, a haptics (devices
capable of recreating tactile or force sensations) based system for
AFM (Atomic Force Microscope) is proposed. The system enables
the nano-scientists to touch and feel the sample surfaces, viewed
through AFM, in order to provide them with better understanding of
the physical properties of the surface, such as roughness, stiffness and
shape of molecular architecture. At this stage, the proposed work uses
of ine images produced using AFM and perform image analysis to
create virtual surfaces suitable for haptics force analysis. The research
work is in the process of extension from of ine to online process
where interaction will be done directly on the material surface for
realistic analysis.
Abstract: Continuously variable transmission (CVT) is a type of
automatic transmission that can change the gear ratio to any arbitrary
setting within the limits. The most common type of CVT operates on
a pulley system that allows an infinite variability between highest and
lowest gears with no discrete steps. However, the current CVT
system with hydraulic actuation method suffers from the power loss.
It needs continuous force for the pulley to clamp the belt and hold the
torque resulting in large amount of energy consumption. This study
focused on the development of an electromechanical actuated control
CVT to eliminate the problem that faced by the existing CVT. It is
conducted with several steps; computing and selecting the
appropriate sizing for stroke length, lead screw system and etc. From
the visual observation it was found that the CVT system of this
research is satisfactory.
Abstract: The current paper presents a numerical approach in solving the conjugate heat transfer problems. A heat conduction code is coupled internally with a computational fluid dynamics solver for developing a couple conjugate heat transfer solver. Methodology of treating non-matching meshes at interface has also been proposed. The validation results of 1D and 2D cases for the developed conjugate heat transfer code have shown close agreement with the solutions given by analysis.
Abstract: Wireless Sensor Networks consist of inexpensive, low power sensor nodes deployed to monitor the environment and collect
data. Gathering information in an energy efficient manner is a critical aspect to prolong the network lifetime. Clustering algorithms have an advantage of enhancing the network lifetime. Current clustering algorithms usually focus on global re-clustering and local re-clustering separately. This paper, proposed a combination of those two reclustering methods to reduce the energy consumption of the network. Furthermore, the proposed algorithm can apply to homogeneous as well as heterogeneous wireless sensor networks. In addition, the cluster head rotation happens, only when its energy drops below a dynamic threshold value computed by the algorithm. The simulation result shows that the proposed algorithm prolong the network lifetime compared to existing algorithms.
Abstract: Job stress is one of the most important concepts for
the today-s corporate as well as institutional world. The current study
is conducted to identify the causes of faculty stress at Higher
Education in Pakistan. For the purpose, Public & Private Business
Schools of Punjab is selected as representative of Pakistan. A sample
of 300 faculty members (214 males, 86 females) responded to the
survey. Regression analysis shows that the Workload, Student
Related issues and Role Conflicts are the major sources contributing
significantly towards producing stress. The study also revealed that
Private sector faculty members experienced more stress as compared
to faculty in Public sector Business Schools. Moreover, females,
younger ages, lower designation & low qualification faculty
members experience more stress as compared to males, older ages,
higher designation and high qualification. The study yield many
significant results for the policy makers of Business Institutions.
Abstract: In modern day disaster recovery mission has become
one of the top priorities in any natural disaster management regime.
Smart autonomous robots may play a significant role in such
missions, including search for life under earth quake hit rubbles,
Tsunami hit islands, de-mining in war affected areas and many other
such situations. In this paper current state of many walking robots are
compared and advantages of hexapod systems against wheeled robots
are described. In our research we have selected a hexapod spider
robot; we are developing focusing mainly on efficient navigation
method in different terrain using apposite gait of locomotion, which
will make it faster and at the same time energy efficient to navigate
and negotiate difficult terrain. This paper describes the method of
terrain negotiation navigation in a hazardous field.
Abstract: In this study, the performance of a high-frequency arc
welding machine including a two-switch inverter is analyzed. The
control of the system is achieved using two different control
techniques i- fuzzy logic control (FLC) ii- state space averaging
based sliding control. Fuzzy logic control does not need accurate
mathematical model of a plant and can be used in nonlinear
applications. The second method needs the mathematical model of
the system. In this method the state space equations of the system are
derived for two different “on" and “off" states of the switches. The
derived state equations are combined with the sliding control rule
considering the duty-cycle of the converter. The performance of the
system is analyzed by simulating the system using SIMULINK tool
box of MATLAB. The simulation results show that fuzzy logic
controller is more robust and less sensitive to parameter variations.
Abstract: A high-linearity and high-speed current-mode sampleand-
hold circuit is designed and simulated using a 0.25μm CMOS
technology. This circuit design is based on low voltage and it utilizes
a fully differential circuit. Due to the use of only two switches the
switch related noise has been reduced. Signal - dependent -error is
completely eliminated by a new zero voltage switching technique.
The circuit has a linearity error equal to ±0.05μa, i.e. 12-bit
accuracy with a ±160 μa differential output - input signal frequency
of 5MHZ, and sampling frequency of 100 MHZ. Third
harmonic is equal to –78dB.
Abstract: In the upgrade process of enterprise information
systems, how to deal with and utilize those legacy systems affects the
efficiency of construction and development of the new system. We
propose an evaluation system, which comprehensively describes the
capacity of legacy information systems in five aspects. Then we
propose a practical legacy systems evaluation method. Base on the
evaluation result, we can determine the current state of legacy system
which was evaluated.
Abstract: The main objectives of this study were to identify
attributes that influence customer satisfaction and determine their
relationships with customer satisfaction. The variables included in
this research are place/ambience, food quality and service quality as
independent variables and customer satisfaction as the dependent
variable. A survey questionnaire which consisted of three parts to
measure demographic factors, independent variables, and dependent
variables was constructed based on items determined by past
research. 149 respondents from one of the well known hotel in Kuala
Lumpur, MALAYSIA were selected as a sample. Psychometric
testing was conducted to determine the reliability and validity of the
questionnaire. From the findings, there were positive significant
relationship between place/ambience (r=0.563**, p=0.000) and
service quality (r=0.544**, p=0.000) with customer satisfaction.
However, although relationship between food quality and customer
satisfaction was significant, it was in the negative direction (r=-
0.268**, p=0.001). New findings were discovered after conducting
this research and previous research findings were strengthened by the
results of this research. Future researchers could concentrate on
determining attributes that influence customer satisfaction when
cost/price is not a factor and reasons for place/ambience is currently
becoming the leading factor in determining customer satisfaction.
Abstract: The characterization and modeling of the dynamic
behavior of many built-up structures under vibration conditions is still
a subject of current research. The present study emphasizes the
theoretical investigation of slip damping in layered and jointed
welded cantilever structures using finite element approach.
Application of finite element method in damping analysis is relatively
recent, as such, some problems particularly slip damping analysis has
not received enough attention. To validate the finite element model
developed, experiments have been conducted on a number of mild
steel specimens under different initial conditions of vibration. Finite
element model developed affirms that the damping capacity of such
structures is influenced by a number of vital parameters such as;
pressure distribution, kinematic coefficient of friction and micro-slip
at the interfaces, amplitude, frequency of vibration, length and
thickness of the specimen. Finite element model developed can be
utilized effectively in the design of machine tools, automobiles,
aerodynamic and space structures, frames and machine members for
enhancing their damping capacity.
Abstract: Together with the industrialization, women began to
be included in business life by peeling off of the tasks given them by
society and they have become a factor of production creating value in
economic and social sense. Thus, women have taken place in the
labor market, majority of which has been formed by men. In this
study, the experiences of women entrepreneurs, who succeed in
business activities, will be analyzed. By the study, current state of the
women entrepreneurs in the labor market of Turkey will be put down,
as a result of interferences obtained from the shared experiences of
women entrepreneurs. Findings obtained at the end of the study are
thought to light the way of future studies for increasing women
entrepreneurship.
Abstract: The error monitoring and processing system, EMPS is
the system located in the substantia nigra of the midbrain, basal
ganglia and cortex of the forebrain, and plays a leading role in error
detection and correction. The main components of EMPS are the
dopaminergic system and anterior cingulate cortex. Although, recent
studies show that alcohol disrupts the EMPS, the ways in which
alcohol affects this system are poorly understood. Based on current
literature data, here we suggest a hypothesis of alcohol-related
glucose-dependent system of error monitoring and processing, which
holds that the disruption of the EMPS is related to the competency of
glucose homeostasis regulation, which in turn may determine the
dopamine level as a major component of EMPS. Alcohol may
indirectly disrupt the EMPS by affecting dopamine level through
disorders in blood glucose homeostasis regulation.
Abstract: Intrusion detection systems (IDS)are crucial components
of the security mechanisms of today-s computer systems.
Existing research on intrusion detection has focused on sequential
intrusions. However, intrusions can also be formed by concurrent
interactions of multiple processes. Some of the intrusions caused
by these interactions cannot be detected using sequential intrusion
detection methods. Therefore, there is a need for a mechanism that
views the distributed system as a whole. L-BIDS (Lattice-Based
Intrusion Detection System) is proposed to address this problem. In
the L-BIDS framework, a library of intrusions and distributed traces
are represented as lattices. Then these lattices are compared in order
to detect intrusions in the distributed traces.
Abstract: Mobile learning (M-learning) integrates mobile
devices and wireless computing technology to enhance the current
conventional learning system. However, there are constraints which
are affecting the implementation of platform and device independent
M-learning. The main aim of this research is to fulfill the following
main objectives: to develop platform independent mobile learning
tool (M-LT) for structured programming course, and evaluate its
effectiveness and usability using ADDIE instructional design model
(ISD) as M-LT life cycle. J2ME (Java 2 micro edition) and XML
(Extensible Markup Language) were used to develop platform
independent M-LT. It has two modules lecture materials and quizzes.
This study used Quasi experimental design to measure effectiveness
of the tool. Meanwhile, questionnaire is used to evaluate the usability
of the tool. Finally, the results show that the system was effective and
also usability evaluation was positive.
Abstract: Severe heart failure is a common problem that has a significant effect on health expenditures in industrialized countries; moreover it reduces patient-s quality of life. However, current research usually focuses either on detailed modeling of the heart or on detailed modeling of the cardiovascular system. Thus, this paper aims to present a sophisticated model of the heart enhanced with an extensive model of the cardiovascular system. Special interest is on the pressure and flow values close to the heart since these values are critical to accurately diagnose causes of heart failure. The model is implemented in Dymola an object-oriented, physical modeling language. Results achieved with the novel model show overall feasibility of the approach. Moreover, results are illustrated and compared to other models. The novel model shows significant improvements.