Abstract: Method of Parallel Joint Channel Coding and
Cryptography has been analyzed and simulated in this paper. The
method is an extension of Soft Input Decryption with feedback,
which is used for improvement of channel decoding of secured
messages. Parallel Joint Channel Coding and Cryptography results in
improved coding gain of channel decoding, which achieves more
than 2 dB. Such results are an implication of a combination of
receiver components and their interoperability.
Abstract: Mobile WiMAX is a broadband wireless solution that
enables convergence of mobile and fixed broadband networks
through a common wide area broadband radio access technology and
flexible network architecture. It adopts Orthogonal Frequency
Division Multiple Access (OFDMA) for improved multi-path
performance in Non-Line-Of-Sight (NLOS) environments. Scalable
OFDMA (SOFDMA) is introduced in the IEEE 802e[1]. WIMAX
system uses one of different types of channel coding but The
mandatory channel coding scheme is based on binary nonrecursive
Convolutional Coding (CC). There are other several optional channel
coding schemes such as block turbo codes, convolutional turbo
codes, and low density parity check (LDPC).
In this paper a comparison between the performance of WIMAX
using turbo code and using convolutional product code (CPC) [2] is
made. Also a combination between them had been done. The CPC
gives good results at different SNR values compared to both the
turbo system, and the combination between them. For example, at
BER equal to 10-2 for 128 subcarriers, the amount of improvement
in SNR equals approximately 3 dB higher than turbo code and equals
approximately 2dB higher than the combination respectively. Several
results are obtained at different modulating schemes (16QAM and
64QAM) and different numbers of sub-carriers (128 and 512).
Abstract: K-Modes is an extension of K-Means clustering algorithm, developed to cluster the categorical data, where the mean is replaced by the mode. The similarity measure proposed by Huang is the simple matching or mismatching measure. Weight of attribute values contribute much in clustering; thus in this paper we propose a new weighted dissimilarity measure for K-Modes, based on the ratio of frequency of attribute values in the cluster and in the data set. The new weighted measure is experimented with the data sets obtained from the UCI data repository. The results are compared with K-Modes and K-representative, which show that the new measure generates clusters with high purity.
Abstract: The cost of developing the software from scratch can
be saved by identifying and extracting the reusable components from
already developed and existing software systems or legacy systems
[6]. But the issue of how to identify reusable components from
existing systems has remained relatively unexplored. We have used
metric based approach for characterizing a software module. In this
present work, the metrics McCabe-s Cyclometric Complexity
Measure for Complexity measurement, Regularity Metric, Halstead
Software Science Indicator for Volume indication, Reuse Frequency
metric and Coupling Metric values of the software component are
used as input attributes to the different types of Neural Network
system and reusability of the software component is calculated. The
results are recorded in terms of Accuracy, Mean Absolute Error
(MAE) and Root Mean Squared Error (RMSE).
Abstract: We developed a new method based on quasimolecular
modeling to simulate the cavity flow in three cavity
shapes: rectangular, half-circular and bucket beer in cgs units. Each
quasi-molecule was a group of particles that interacted in a fashion
entirely analogous to classical Newtonian molecular interactions.
When a cavity flow was simulated, the instantaneous velocity vector
fields were obtained by using an inverse distance weighted
interpolation method. In all three cavity shapes, fluid motion was
rotated counter-clockwise. The velocity vector fields of the three
cavity shapes showed a primary vortex located near the upstream
corners at time t ~ 0.500 s, t ~ 0.450 s and t ~ 0.350 s, respectively.
The configurational kinetic energy of the cavities increased as time
increased until the kinetic energy reached a maximum at time t ~
0.02 s and, then, the kinetic energy decreased as time increased. The
rectangular cavity system showed the lowest kinetic energy, while
the half-circular cavity system showed the highest kinetic energy.
The kinetic energy of rectangular, beer bucket and half-circular
cavities fluctuated about stable average values 35.62 x 103, 38.04 x
103 and 40.80 x 103 ergs/particle, respectively. This indicated that the
half-circular shapes were the most suitable shape for a shrimp pond
because the water in shrimp pond flows best when we compared with
rectangular and beer bucket shape.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: This paper presents three new methodologies for the
basic operations, which aim at finding new ways of computing union
(maximum) and intersection (minimum) membership values by
taking into effect the entire membership values in a fuzzy set. The
new methodologies are conceptually simple and easy from the
application point of view and are illustrated with a variety of
problems such as Cartesian product of two fuzzy sets, max –min
composition of two fuzzy sets in different product spaces and an
application of an inverted pendulum to determine the impact of the
new methodologies. The results clearly indicate a difference based on
the nature of the fuzzy sets under consideration and hence will be
highly useful in quite a few applications where different values have
significant impact on the behavior of the system.
Abstract: The present study focuses on methods allowing a convenient and quick calculation of the SIFs in order to predict the static adhesive strength of bonded joints. A new SIF calculation method is proposed, based on the stresses obtained from a FE model at a reference point located in the adhesive layer at equal distance of the free-edge and of the two interfaces. It is shown that, even limiting ourselves to the two main modes, i.e. the opening and the shearing modes, and using the values of the stresses resulting from a low detailed FE model, an efficient calculation of the peeling stress at adhesive-substrate corners can be obtained by this way. The proposed method is interesting in that it can be the basis of a prediction tool that will allow the designer to quickly evaluate the SIFs characterizing a particular application without developing a detailed analysis.
Abstract: The purpose of this study is to analyze the cognitive
and travel experience the situation of the tourist attraction of the sport
tourism in Penghu. This study used a questionnaires, the main island
of Taiwan to Penghu in the way of marine sports tourists adopted the
designated convenience sampling method, a total of 1447 valid
questionnaires. After statistical analysis, this study found that: 1.
Tourists to Penghu sports tourism attraction cognitive as “good air
quality, suitable for water activities". 2. Tourists in Penghu's tourism
experience, “Let me taste the delicious specialties and snacks". 3. The
attraction of the sport tourism, travel experience and perceived value
are correlated, and both the perceived value with a high degree of
predictive ability. Based on the findings of this study not only for
Penghu's tourism industry with the unit in charge of the proposed
operating and suggestions for future research to other researchers.
Abstract: The requirement to improve software productivity has
promoted the research on software metric technology. There are
metrics for identifying the quality of reusable components but the
function that makes use of these metrics to find reusability of
software components is still not clear. These metrics if identified in
the design phase or even in the coding phase can help us to reduce the
rework by improving quality of reuse of the component and hence
improve the productivity due to probabilistic increase in the reuse
level. CK metric suit is most widely used metrics for the objectoriented
(OO) software; we critically analyzed the CK metrics, tried
to remove the inconsistencies and devised the framework of metrics
to obtain the structural analysis of OO-based software components.
Neural network can learn new relationships with new input data and
can be used to refine fuzzy rules to create fuzzy adaptive system.
Hence, Neuro-fuzzy inference engine can be used to evaluate the
reusability of OO-based component using its structural attributes as
inputs. In this paper, an algorithm has been proposed in which the
inputs can be given to Neuro-fuzzy system in form of tuned WMC,
DIT, NOC, CBO , LCOM values of the OO software component and
output can be obtained in terms of reusability. The developed
reusability model has produced high precision results as expected by
the human experts.
Abstract: In this study, a new procedure for inspecting damages on LNG storage tanks was proposed with the use of structural diagnostic techniques: i.e., nondestructive inspection techniques such as macrography, the hammer sounding test, the Schmidt hammer test, and the ultrasonic pulse velocity test, and destructive inspection techniques such as the compressive strength test, the chloride penetration test, and the carbonation test. From the analysis of all the test results, it was concluded that the LNG storage tank cover was in good condition. Such results were also compared with the Korean concrete standard specifications and design values. In addition, the remaining life of the LNG storage tank was estimated by using existing models. Based on the results, an LNG storage tank cover performance evaluation procedure was suggested.
Abstract: Fuzzy sets theory affirmed that the linguistic value for
every contraries relation is complementary. It was stressed in the
intuitionistic fuzzy sets (IFS) that the conditions for contraries
relations, which are the fuzzy values, cannot be greater than one.
However, complementary in two contradict phenomena are not
always true. This paper proposes a new idea condition for conflicting
bifuzzy sets by relaxing the condition of intuitionistic fuzzy sets.
Here, we will critically forward examples using triangular fuzzy
number in formulating a new condition for conflicting bifuzzy sets
(CBFS). Evaluation of positive and negative in conflicting
phenomena were calculated concurrently by relaxing the condition in
IFS. The hypothetical illustration showed the applicability of the new
condition in CBFS for solving non-complement contraries
intuitionistic evaluation. This approach can be applied to any
decision making where conflicting is very much exist.
Abstract: Indices summarizing community structure are used to
evaluate fundamental community ecology, species interaction,
biogeographical factors, and environmental stress. Some of these
indices are insensitive to gross community changes induced by
contaminants of pollution. Diversity indices and similarity indices are
reviewed considering their ecological application, both theoretical
and practical. For some useful indices, empirical equations are given
to calculate the expected maximum value of the indices to which the
observed values can be related at any combination of sample sizes at
the experimental sites. This paper examines the effects of sample size
and diversity on the expected values of diversity indices and
similarity indices, using various formulae. It has been shown that all
indices are strongly affected by sample size and diversity. In some
indices, this influence is greater than the others and an attempt has
been made to deal with these influences.
Abstract: A novel calibration approach that aims to reduce
ASM2d parameter subsets and decrease the model complexity is
presented. This approach does not require high computational
demand and reduces the number of modeling parameters required to
achieve the ASMs calibration by employing a sensitivity and iteration
methodology. Parameter sensitivity is a crucial factor and the
iteration methodology enables refinement of the simulation parameter
values. When completing the iteration process, parameters values are
determined in descending order of their sensitivities. The number of
iterations required is equal to the number of model parameters of the
parameter significance ranking. This approach was used for the
ASM2d model to the evaluated EBPR phosphorus removal and it was
successful. Results of the simulation provide calibration parameters.
These included YPAO, YPO4, YPHA, qPHA, qPP, μPAO, bPAO, bPP, bPHA,
KPS, YA, μAUT, bAUT, KO2 AUT, and KNH4 AUT. Those parameters were
corresponding to the experimental data available.
Abstract: The nature of wireless ad hoc and sensor networks
make them very attractive to attackers. One of the most popular and
serious attacks in wireless ad hoc networks is wormhole attack and
most proposed protocols to defend against this attack used
positioning devices, synchronized clocks, or directional antennas.
This paper analyzes the nature of wormhole attack and existing
methods of defending mechanism and then proposes round trip time
(RTT) and neighbor numbers based wormhole detection mechanism.
The consideration of proposed mechanism is the RTT between two
successive nodes and those nodes- neighbor number which is needed
to compare those values of other successive nodes. The identification
of wormhole attacks is based on the two faces. The first consideration
is that the transmission time between two wormhole attack affected
nodes is considerable higher than that between two normal neighbor
nodes. The second detection mechanism is based on the fact that by
introducing new links into the network, the adversary increases the
number of neighbors of the nodes within its radius. This system does
not require any specific hardware, has good performance and little
overhead and also does not consume extra energy. The proposed
system is designed in ad hoc on-demand distance vector (AODV)
routing protocol and analysis and simulations of the proposed system
are performed in network simulator (ns-2).
Abstract: This paper deals with a periodic-review substitutable
inventory system for a finite and an infinite number of periods. Here
an upward substitution structure, a substitution of a more costly item
by a less costly one, is assumed, with two products. At the beginning
of each period, a stochastic demand comes for the first item only,
which is quality-wise better and hence costlier. Whenever an arriving
demand finds zero inventory of this product, a fraction of unsatisfied
customers goes for its substitutable second item. An optimal ordering
policy has been derived for each period. The results are illustrated
with numerical examples. A sensitivity analysis has been done to
examine how sensitive the optimal solution and the maximum profit
are to the values of the discount factor, when there is a large number
of periods.
Abstract: In this paper, we represent protein structure by using
graph. A protein structure database will become a graph database.
Each graph is represented by a spectral vector. We use Jacobi
rotation algorithm to calculate the eigenvalues of the normalized
Laplacian representation of adjacency matrix of graph. To measure
the similarity between two graphs, we calculate the Euclidean
distance between two graph spectral vectors. To cluster the graphs,
we use M-tree with the Euclidean distance to cluster spectral vectors.
Besides, M-tree can be used for graph searching in graph database.
Our proposal method was tested with graph database of 100 graphs
representing 100 protein structures downloaded from Protein Data
Bank (PDB) and we compare the result with the SCOP hierarchical
structure.
Abstract: Religion revival including Islam in Kazakhstan represents reaction, first of all on internal social and political change, events after disintegration of the USSR. Process of revival of Kazakhstan Islam was accompanied as positive, so by negative tendencies. Old mosques were restored, were under construction new, Islamic schools and high schools were created, was widely studied religious the dogmatic person, the corresponding literature was published, expanded contacts with foreign Muslim brothers in the faith, the centers of the Arab-Muslim culture extended. At the same time in Kazakhstan, there are religious-political parties and movements, pursuing radical goals down to change the spiritual and cultural identity of Muslims of Kazakhstan by the forcible introduction of non-traditional religious and political, ethnic and cultural values.
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: The Brazilian legislation has only established
diagnostic reference levels (DRLs) in terms of Multiple Scan
Average Dose (MSAD) as a quality control parameter for computed
tomography (CT) scanners. Compliance with DRLs can be verified
by measuring the Computed Tomography Kerma Index (Ca,100) with
a pencil ionization chamber or by obtaining the kerma distribution in
CT scans with radiochromic films or rod shape lithium fluoride
termoluminescent dosimeters (TLD-100). TL dosimeters were used
to record kerma profiles and to determine MSAD values of a Bright
Speed model GE CT scanner. Measurements were done with
radiochromic films and TL dosimeters distributed in cylinders
positioned in the center and in four peripheral bores of a standard
polymethylmethacrylate (PMMA) body CT dosimetry phantom.
Irradiations were done using a protocol for adult chest. The
maximum values were found at the midpoint of the longitudinal axis.
The MSAD values obtained with three dosimetric techniques were
compared.