Abstract: The logistical requirements placed on industrial manufacturing companies are steadily increasing. In order to meet those requirements, a consistent and efficient concept is necessary for production control. Set up properly, production control offers considerable potential with respect to achieving the logistical targets. As experience with the many production control methods already in existence and their compatibility is, however, often inadequate, this article describes a systematic approach to the configuration of production control based on the Lödding model. This model enables production control to be set up individually to suit a company and the requirements. It therefore permits today-s demands regarding logistical performance to be met.
Abstract: Absorptive characteristics of polyaniline synthesized
in mixture of water and acetonitrile in 50/50 volume ratio was
studied. Synthesized polyaniline in powder shape is used as an
adsorbent to remove toxic hexavalent chromium from aqueous
solutions. Experiments were conducted in batch mode with different
variables such as agitation time, solution pH and initial concentration
of hexavalent chromium. Removal mechanism is the combination of
surface adsorption and reduction. The equilibrium time for removal
of Cr(T) and Cr(VI) was about 2 and 10 minutes respectively. The
optimum pH for total chromium removal occurred at pH 7 and
maximum hexavalent chromium removal took place under acidic
condition at pH 3. Investigating the isothermal characteristics showed
that the equilibrium adsorption data fitted both Freundlich-s and
Langmuir-s isotherms. The maximum adsorption of chromium was
calculated 36.1 mg/g for polyaniline
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: Nowadays, without the awareness of consumer
behavior and correct understanding of it, it is not possible for organizations to take appropriate measures to meet the consumer
needs and demands. The aim of this paper is the identification and
prioritization of the factors affecting the consumer behavior based on
the product value. The population of the study includes all the
consumers of furniture producing firms in East Azarbaijan province,
Iran. The research sample includes 93 people selected by the sampling formula in unlimited population. The data collection
instrument was a questionnaire, the validity of which was confirmed
through face validity and the reliability of which was determined,
using Cronbach's alpha coefficient. The Kolmogorov-Smironov test
was used to test data normality, the t-test for identification of factors
affecting the product value, and Friedman test for prioritizing the
factors. The results show that quality, satisfaction, styling, price, finishing operation, performance, safety, worth, shape, use, and
excellence are placed from 1 to 11 priorities, respectively.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: One of the main problems of suspended cable structures is initial shape change under the action of non uniform load. The problem can be solved by increasing of weight of construction or by using of prestressing. But this methods cause increasing of materials consumption of suspended cable structure. The cable truss usage is another way how the problem of shape change under the action of non uniform load can be fixed. The cable trusses with the vertical and inclined suspensions, cross web and single cable were analyzed as the main load-bearing structures of suspension bridge. It was shown, that usage of cable truss allows to reduce the vertical displacements up to 32% in comparison with the single cable in case of non uniformly distributed load. In case of uniformly distributed load single cable is preferable.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: In the present study, the effect of ferrous sulfate concentration and total solids on bioleaching of heavy metals from sewage sludge has been examined using indigenous iron-oxidizing microorganisms. The experiments on effects of ferrous sulfate concentrations on bioleaching were carried out using ferrous sulfate of different concentrations (5-20 g L-1) to optimize the concentration of ferrous sulfate for maximum bioleaching. A rapid change in the pH and ORP took place in first 2 days followed by a slow change till 16th day in all the sludge samples. A 10 g L-1 ferrous sulfate concentration was found to be sufficient in metal bioleaching in the following order: Zn: 69%>Cu: 52%>Cr: 46%>Ni: 45. Further, bioleaching using 10 g/L ferrous sulfate was found to be efficient up to 20 g L-1 sludge solids concentration. The results of the present study strongly indicate that using 10 g L-1 ferrous sulfate indigenous iron-oxidizing microorganisms can bring down pH to a value needed for significant metal solubilization.
Abstract: In this paper is described a new conception of the
Cartesian robot for automated assembly and also disassembly
process. The advantage of this conception is the utilization the
Cartesian assembly robot with its all peripheral automated devices for
assembly of the assembled product. The assembly product in the end
of the lifecycle can be disassembled with the same Cartesian
disassembly robot with the use of the same peripheral automated
devices and equipment. It is a new approach to problematic solving
and development of the automated assembly systems with respect to
lifecycle management of the assembly product and also assembly
system with Cartesian robot. It is also important to develop the
methodical process for design of automated assembly and
disassembly system with Cartesian robot. Assembly and disassembly
system use the same Cartesian robot input and output devices,
assembly and disassembly units in one workplace with different
application. Result of design methodology is the verification and
proposition of real automated assembly and disassembly workplace
with Cartesian robot for known verified model of assembled actuator.
Abstract: The clinical usefulness of heart rate variability is
limited to the range of Holter monitoring software available. These
software algorithms require a normal sinus rhythm to accurately
acquire heart rate variability (HRV) measures in the frequency
domain. Premature ventricular contractions (PVC) or more
commonly referred to as ectopic beats, frequent in heart failure,
hinder this analysis and introduce ambiguity. This investigation
demonstrates an algorithm to automatically detect ectopic beats by
analyzing discrete wavelet transform coefficients. Two techniques
for filtering and replacing the ectopic beats from the RR signal are
compared. One technique applies wavelet hard thresholding
techniques and another applies linear interpolation to replace ectopic
cycles. The results demonstrate through simulation, and signals
acquired from a 24hr ambulatory recorder, that these techniques can
accurately detect PVC-s and remove the noise and leakage effects
produced by ectopic cycles retaining smooth spectra with the
minimum of error.
Abstract: This study explored the relationship between
occupational stress and the perceived effectiveness of men and
women managers in Ghanaian organizations. The exploration is
underlined by attempt to understand the degree to which male and
female managers in Ghanaian organizations experience occupational
stress at the workplace. The purpose is to examine the sources and
extents of occupational stress experienced by male and female
managers in Ghana. Data was collected using questionnaires and
analyzed using both descriptive statistics and correlation analysis.
The results showed that female managers in Ghana are more likely to
report of more stress experiences in the workplace than their male
counterparts. The female managers are more likely to perceive role
conflict and alienation as job stressors while the male managers
perceived blocked career as a major source of workplace stress. It is
concluded that despite the female managers experiencing enormous
level of occupational stress, there was no significant differences
between their managerial effectiveness and that of the male.
Abstract: In-place sorting algorithms play an important role in many fields such as very large database systems, data warehouses, data mining, etc. Such algorithms maximize the size of data that can be processed in main memory without input/output operations. In this paper, a novel in-place sorting algorithm is presented. The algorithm comprises two phases; rearranging the input unsorted array in place, resulting segments that are ordered relative to each other but whose elements are yet to be sorted. The first phase requires linear time, while, in the second phase, elements of each segment are sorted inplace in the order of z log (z), where z is the size of the segment, and O(1) auxiliary storage. The algorithm performs, in the worst case, for an array of size n, an O(n log z) element comparisons and O(n log z) element moves. Further, no auxiliary arithmetic operations with indices are required. Besides these theoretical achievements of this algorithm, it is of practical interest, because of its simplicity. Experimental results also show that it outperforms other in-place sorting algorithms. Finally, the analysis of time and space complexity, and required number of moves are presented, along with the auxiliary storage requirements of the proposed algorithm.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: One of the essential requirements for the human
beings is the house for living. This is necessary to make the place of
satisfaction for contemporary houses residents by attention to their
culture. In this article represented the relevant theoretical literature
on cultural symbols by use the architecture semiotic to construct the
houses as a better place for living. In fact, make a place for everyday
life with changing the house to the home is one of the most
challengeable subject for architects all around the world. The target
of this article is to find Cypriot houses cultural symbols that assist
architect to design and build contemporary houses, to make more
satisfaction for its residents according to Cypriot life style and their
culture. This paper is based on researching the effect of cultural
symbols on housing, would require various types of methods.
However, this study focuses on two methods, which are quantitative
and qualitative. The purpose of the case-specific study is to finding
the symbols that used in contemporary houses by attention to the
Cypriot cultural symbols in Famagusta houses.
Abstract: The prospective analysis is presented as an important tool to identify the most relevant opportunities and needs in research and development from planned interventions in innovation systems. This study chose Phyllanthus niruri, known as "stone break" to describe the knowledge about the specie, by using biotechnological forecasting through the software Vantage Point. It can be seen a considerable increase in studies on Phyllanthus niruri in recent years and that there are patents about this plant since twenty-five years ago. India was the country that most carried out research on the specie, showing interest, mainly in studies of hepatoprotection, antioxidant and anti-cancer activities. Brazil is in the second place, with special interest for anti-tumor studies. Given the identification of the Brazilian groups that exploit the species it is possible to mediate partnerships and cooperation aiming to help on the implementing of the Program of Herbal medicines (phytotherapics) in Brazil.
Abstract: Scalability poses a severe threat to the existing
DRAM technology. The capacitors that are used for storing and
sensing charge in DRAM are generally not scaled beyond 42nm.
This is because; the capacitors must be sufficiently large for reliable
sensing and charge storage mechanism. This leaves DRAM memory
scaling in jeopardy, as charge sensing and storage mechanisms
become extremely difficult. In this paper we provide an overview of
the potential and the possibilities of using Phase Change Memory
(PCM) as an alternative for the existing DRAM technology. The
main challenges that we encounter in using PCM are, the limited
endurance, high access latencies, and higher dynamic energy
consumption than that of the conventional DRAM. We then provide
an overview of various methods, which can be employed to
overcome these drawbacks. Hybrid memories involving both PCM
and DRAM can be used, to achieve good tradeoffs in access latency
and storage density. We conclude by presenting, the results of these
methods that makes PCM a potential replacement for the current
DRAM technology.
Abstract: Fine-grained data replication over the Internet allows duplication of frequently accessed data objects, as opposed to entire sites, to certain locations so as to improve the performance of largescale content distribution systems. In a distributed system, agents representing their sites try to maximize their own benefit since they are driven by different goals such as to minimize their communication costs, latency, etc. In this paper, we will use game theoretical techniques and in particular auctions to identify a bidding mechanism that encapsulates the selfishness of the agents, while having a controlling hand over them. In essence, the proposed game theory based mechanism is the study of what happens when independent agents act selfishly and how to control them to maximize the overall performance. A bidding mechanism asks how one can design systems so that agents- selfish behavior results in the desired system-wide goals. Experimental results reveal that this mechanism provides excellent solution quality, while maintaining fast execution time. The comparisons are recorded against some well known techniques such as greedy, branch and bound, game theoretical auctions and genetic algorithms.