Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: The launching nose plays an important role in the
incremental launching construction. The parameters of the launching
nose essentially affect the internal forces of the girder during the
construction. The appropriate parameters can decrease the internal
forces in the girder and save the material and reduce the cost. The
simplified structural model, which is made with displacement method
according to the characteristic of incremental launching construction
and the variation rule of the internal forces, calculates and analyzes the
effect of the length, the rigidity and weight of launch nose on the
internal forces of girder during the incremental launching
construction. The method, which can calculate the launching nose
parameters for the optimum incremental launching construction, is
achieved. This method is simple, reliable and easy for practical use.
Abstract: The wisest economic decision of United States in the
20th century was establishing the favorable international monetary
system, and capturing the leadership position in it. This decision gave
economic hegemony to the US for the next more than 7 decades. The
continuation of this hegemony till the next decade seems difficult as
the US economy is under continuous streams of recessions since
2007. On the other hand, Chinese economy is progressing with a
very fast speed and is estimated to pass the US economy till 2025, in
various aspects. Will the US be able to continue its leadership in the
IMS? Will China replace US in the international monetary system?
The answers to these questions have been explored by comparing the
economic competitiveness of US and China, with respect to each
other. The paper concludes that the change in global economic
environment will compel US to share the leadership of international
monetary system with China. This sharing will solve most problems
of the current IMS, but will also birth some new problems.
Abstract: Presented herein is an assessment of current nonlinear
static procedures (NSPs) for seismic evaluation of bucklingrestrained
braced frames (BRBFs) which have become a favorable
lateral-force resisting system for earthquake resistant buildings. The
bias and accuracy of modal, improved modal pushover analysis
(MPA, IMPA) and mass proportional pushover (MPP) procedures
are comparatively investigated when they are applied to BRBF
buildings subjected to two sets of strong ground motions. The
assessment is based on a comparison of seismic displacement
demands such as target roof displacements, peak floor/roof
displacements and inter-story drifts. The NSP estimates are compared
to 'exact' results from nonlinear response history analysis (NLRHA).
The response statistics presented show that the MPP
procedure tends to significantly overestimate seismic demands of
lower stories of tall buildings considered in this study while MPA
and IMPA procedures provide reasonably accurate results in
estimating maximum inter-story drift over all stories of studied BRBF
systems.
Abstract: The results show that the bridge equipped with seismic isolation bearing system shows a high amount of energy dissipation. The purpose of the present study is to analyze the overall performance of continuous curved highway viaducts with different bearing supports, with an emphasis on the effectiveness of seismic isolation based on lead rubber bearing and hedge reaction force bearing system consisted of friction sliding bearing and rubber bearing. The bridge seismic performance has been evaluated on six different cases with six bearing models. The effects of the different arrangement of bearing on the deck superstructure displacements, the seismic damage at the bottom of the piers, movement track at the pier-s top and the total and strain energies absorbed by the structure are evaluated. In conclusion, the results provide sufficient evidence of the effectiveness on the use of seismic isolation on steel curved highway bridges.
Abstract: Presently and in line with the United Nations (EPA),
human thinking system has shifted towards clean fuels so as to
maintain a cleaner environment and to save our planet earth.
One of the most successful studies in order to achieve new
energies includes the use of animal wastes and their organic residues,
and the result of these researches has been represented in the form of
very simple and cheap methods called biogas technology. Biogas
technology has developed a lot in the recent decades; its reason is the
high cost of fossil fuels and the greater attention of countries to the
environmental pollutions due to the consumption of this kind of
fuels.
IRAN is ready for the optimized application of renewable
energies, having much enriched resources of this kind of energies; so
a special place could be considered for it when making programs.
The purpose of biogas technology is the recovery of energy and
finally the protection of the environment, which is much appropriate
for the third world farmers with respect to their technical abilities and
economic potentials. Studies show that the production and
consumption of biogas is appropriate and economic in IRAN,
because of the high amount of waste in the agriculture sector, the
significant amount of animal and human excrement production, the
great volume of garbage produced and the most important the
specific social, climatic and agricultural conditions in IRAN, in order
to proceed towards the reduction of pollution due to the use of fossil
fuels.
Abstract: Previous researches found that conventional WBL is effective for meaningful learner, because rote learner learn by repeating without thinking or trying to understand. It is impossible to have full benefit from conventional WBL. Understanding of rote learner-s intention and what influences it becomes important. Poorly designed user interface will discourage rote learner-s cultivation and intention to use WBL. Thus, user interface design is an important factor especially when WBL is used as comprehensive replacement of conventional teaching. This research proposes the influencing factors that can enhance learner-s intention to use the system. The enhanced TAM is used for evaluating the proposed factors. The research result points out that factors influencing rote learner-s intention are Perceived Usefulness of Homepage Content Structure, Perceived User Friendly Interface, Perceived Hedonic Component, and Perceived (homepage) Visual Attractiveness.
Abstract: Political transition of agricultural properties in Poland and the former German Democratic Republic (GDR) after 1989 had
to include not only Reprivatization but also the issue of returning the
properties in kind to their former owners. Restitution in kind applied
in GDR to all forms of ownership which were subject to
expropriation between 1933 and 1989 except for properties taken
over during Soviet occupation in 1945-49. This issue was one of the flashpoints during the process of ownership changes. Privatization,
limited as it was, took place in unequal legal environment where only
one group of owners was privileged. Executing restitution in kind
created a feeling of uncertainty among potential real estate buyers.
Abstract: Cities denote instantaneously a challenge and an
opportunity for climate change policy. Cities are the place where
most energy services are needed because urbanization is closely
linked to high population densities and concentration of economic
activities and production (Urban energy demand). Consequently, it is
critical to explain about the role of cities within the world-s energy
systems and its correlation with the climate change issue. With more
than half of the world-s population already living in urban areas, and
that percentage expected to rise to 75 per cent by 2050, it is clear that
the path to sustainable development must pass through cities. Cities
expanding in size and population pose increased challenges to the
environment, of which energy is part as a natural resource, and to the
quality of life. Nowadays, most cities have already understood the
importance of sustainability, both at their local scale as in terms of
their contribution to sustainability at higher geographical scales. It
requires the perception of a city as a complex and dynamic
ecosystem, an open system, or cluster of systems, where the energy
as well as the other natural resources is transformed to satisfy the
needs of the different urban activities. In fact, buildings and
transportation generally represent most of cities direct energy
demand, i.e., between 60 per cent and 80 per cent of the overall
consumption. Buildings, both residential and services are usually
influenced by the local physical and social conditions. In terms of
transport, the energy demand is also strongly linked with the specific
characteristics of a city (urban mobility).The concept of a “smart
city" builds on statistics as seven key axes of a city-s success in
moving towards common platform (brain nerve)of sustainable urban
energy systems.
With the aforesaid knowledge, the authors have suggested a frame
work to role of cities, as energy actors for smart city management.
The authors have discusses the potential elements needed for energy
in smart cities and also identified potential energy actions and
relevant barriers. Furthermore, three levels of city smartness in cities
actions to overcome market /institutional failures with a local
approach are distinguished. The authors have made an attempt to
conceive and implement concepts of city smartness by adopting the
city or local government as nerve center through an integrated
planning approach. Finally, concluding with recommendations for
the organization of the Smart Sustainable Cities for positive changes
of urban India.
Abstract: Current air conditioning system is using refrigerant as
the cooling medium. The main purpose of this study is to develop an
air conditioning system using chill water as the cooling medium. In
this system, chill water used to replace refrigerant as the cooling
medium. This study is focus on the split type unit air conditioning
system only. It will be involving some renovation on the indoor unit
and freezer. The cooling capability of this system was validate by few
series of testing, which conducted at standard 36m3 office room.
Result of the testing found that 0.1 m3 of chill water is able to
maintain the room temperature within standard up to 4 ~ 8 hours. It
expected able to maintain room temperature up to 10 hour with some
improvement.
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: Hair is a non homogenous complex material which
can be associated with a polymer. It is made up 95% of Keratin.
Hair has a great social significance for human beings. In the High
Middle Ages, for example, long hairs have been reserved for kings
and nobles.
Most common interest in hair is focused on hair growth, hair types
and hair care, but hair is also an important biomaterial which can
vary depending on ethnic origin or on age, hair colour for example
can be a sign of ethnic ancestry or age (dark hair for Asiatic, blond
hair for Caucasian and white hair for old people in general).
In this context, different approaches have been conducted to
determine the differences in mechanical properties and characterize
the fracture topography at the surface of hair depending on its type
and its age.
A tensile testing machine was especially designed to achieve
tensile tests on hair. This device is composed of a microdisplacement
system and a force sensor whose peak load is limited to
3N. The curves and the values extracted from each experiment, allow
us to compare the evolution of the mechanical properties from one
hair to another.
Observations with a Scanning Electron Microscope (SEM) and
with an interferometer were made on different hairs. Thus, it is
possible to access the cuticle state and the fracture topography for
each category.
Abstract: Landfill gas, particularly methane is one of the
greenhouse gases which contributes to global warming. This paper presents the findings of a study on methane gas production from
simulated landfill reactor under saturated conditions. A reactor was constructed to represent a landfill cell of 2.5 m thickness on sandy
soil. The reactor was 0.2 m in diameter and 4 m in height. One meter of sand and pebble layer was packed at the bottom of the reactor
followed by 2.5 m of solid waste layer and 0.4 m of sand layer as the cover soil. Degradation of waste in the solid waste layer was at
acidification stage as indicated by the leachate quality with COD as
high as 55,511 mg/L and pH as low as 5.1. However, methanogenic
environment was established at the bottom sand layer after one year of operation indicated by pH of 7.2 and methane gas generation.
Leachate degradation took place as the leachate moved through the
sand layer at an infiltration of rate 0.7 cm/day. This resulted in landfill gas production of 77 mL/day/kg containing 55 to 65% methane. The application of sand layer contributed to the gas
production from landfill by an in-situ degradation of leachate in the
sand at the bottom of the landfill.
Abstract: A dual-reciprocity boundary element method is presented
for the numerical solution of a class of axisymmetric elastodynamic
problems. The domain integrals that arise in the integrodifferential
formulation are converted to line integrals by using the
dual-reciprocity method together suitably constructed interpolating
functions. The second order time derivatives of the displacement
in the governing partial differential equations are suppressed by
using Laplace transformation. In the Laplace transform domain, the
problem under consideration is eventually reduced to solving a system
of linear algebraic equations. Once the linear algebraic equations are
solved, the displacement and stress fields in the physical domain can
be recovered by using a numerical technique for inverting Laplace
transforms.
Abstract: Although automotive industry has brought different beneficiaries to human life, it is being pointed out as one of the major cause of global air pollution which resulted in climate change, smog, green house gases (GHGs), and human diseases by many reasons. Since auto industry is one of the largest consumers of fossil fuels, the realization of green innovations is becoming a crucial choice to meet the challenges towards sustainable development. Recently, many auto manufacturers have embarked on green technology initiatives to gain a competitive advantage in the global market; however, innovative manufacturing systems and technologies can enhance operational performance only if the human resource management is in place to elicit the motivation of the employees and develop their organizational expertise. No organization can perform at peak levels unless each employee is committed to the company goals and works as an effective team member. Strategic human resource practices are the primary means by which firms can shape the skills, attitudes, and behavior of individuals to align with the business strategic objectives. This study investigates on the comprehensive approach of multiple advanced technology innovations and human resource management at Toyota Motor Corporation as the market leader of full hybrid technology in the automotive industry. Then, HRM framework of the company is described and three sets of human resource practices that support the innovation-oriented HR system, presented. Finally, a conceptual framework for innovativeness in green technology in automotive industry by applying a deliberate strategic HR management system and knowledge management with the intervening factors of organizational culture, knowledge application and knowledge sharing is proposed.
Abstract: In this paper, the construction of a detailed spine
model is presented using the LifeMOD Biomechanics Modeler. The
detailed spine model is obtained by refining spine segments in
cervical, thoracic and lumbar regions into individual vertebra
segments, using bushing elements representing the intervertebral
discs, and building various ligamentous soft tissues between
vertebrae. In the sagittal plane of the spine, constant force will be
applied from the posterior to anterior during simulation to determine
dynamic characteristics of the spine. The force magnitude is
gradually increased in subsequent simulations. Based on these
recorded dynamic properties, graphs of displacement-force
relationships will be established in terms of polynomial functions by
using the least-squares method and imported into a haptic integrated
graphic environment. A thoracolumbar spine model with complex
geometry of vertebrae, which is digitized from a resin spine
prototype, will be utilized in this environment. By using the haptic
technique, surgeons can touch as well as apply forces to the spine
model through haptic devices to observe the locomotion of the spine
which is computed from the displacement-force relationship graphs.
This current study provides a preliminary picture of our ongoing
work towards building and simulating bio-fidelity scoliotic spine
models in a haptic integrated graphic environment whose dynamic
properties are obtained from LifeMOD. These models can be helpful
for surgeons to examine kinematic behaviors of scoliotic spines and
to propose possible surgical plans before spine correction operations.
Abstract: Safety Critical hard Real-Time Systems are ever
present in the avionics industry. The Model Driven Architecture
(MDA) offers different levels of model abstraction and generation.
This paper discusses our concerns relating to model development and
generation when using the MDA approach in the avionics industry.
These concerns are based on our experience when looking into
adopting the MDA as part of avionics systems development. We
place emphasis on transformations between model types and discuss
possible benefits of adopting an MDA approach as part of the
software development life cycle.