Abstract: The volume of biosolids produced in Malaysia
nowadays had increased proportionally to its population size. The end
products from the waste treatments were mounting, thus inevitable
that in the end the environment will be surrounded by the waste. This
study was conducted to investigate the suitability of biosolids to be
reused as fertilizer for non-food crop. By varying the concentration of
biosolids applied onto the soil, growth of five ornamental plant
samples were tested for eight consecutive weeks. The results show
that the pH of the soil after the addition of biosolids ranges from 6.45
to 6.56 which is suitable for the plant growth. The soil samples that
contains biosolid also show higher amount of macronutrients (N, P,
K) and the heavy metals content are significantly increased in the
plant however it does not exceed the guidelines drawn by the
Environmental Protection Agency. It is also proven that there was
only small significant different in the performance of plant growth
between biosolids and commercial fertilizer. It can be seen that
biosolids was able to perform just as well as commercial fertilizer.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: An area-integrating method that uses the technique of total integrated light scatter for evaluating the root mean square height of the surface Sq has been presented in the paper. It is based on the measurement of the scatter power using a flat photodiode integrator rather than an optical sphere or a hemisphere. By this means, one can obtain much less expensive and smaller instruments than traditional ones. Thanks to this, they could find their application for surface control purposes, particularly in small and medium size enterprises. A description of the functioning of the measuring unit as well as the impact caused by different factors on its properties is presented first. Next, results of measurements of the Sq values performed for optical, silicon and metal samples have been shown. It has been also proven that they are in a good agreement with the results obtained using the Ulbricht sphere instrument.
Abstract: The analysis of Acoustic Emission (AE) signal
generated from metal cutting processes has often approached
statistically. This is due to the stochastic nature of the emission
signal as a result of factors effecting the signal from its generation
through transmission and sensing. Different techniques are applied in
this manner, each of which is suitable for certain processes. In metal
cutting where the emission generated by the deformation process is
rather continuous, an appropriate method for analysing the AE signal
based on the root mean square (RMS) of the signal is often used and
is suitable for use with the conventional signal processing systems.
The aim of this paper is to set a strategy in tool failure detection in
turning processes via the statistic analysis of the AE generated from
the cutting zone. The strategy is based on the investigation of the
distribution moments of the AE signal at predetermined sampling.
The skews and kurtosis of these distributions are the key elements in
the detection. A normal (Gaussian) distribution has first been
suggested then this was eliminated due to insufficiency. The so
called Beta distribution was then considered, this has been used with
an assumed β density function and has given promising results with
regard to chipping and tool breakage detection.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: It is believed that DNA damaging toxic metabolites contributes to the development of different pathological conditions. To prevent harmful influence of toxic agents, cells developed number of protecting mechanisms, such as enzymatic reaction of detoxification of reactive metabolites and repair of DNA damage. The aim of the study was to examine the association between polymorphism of GSTT1/GSTM1 and XRCC1/3 genes and coronary artery disease (CAD) incidence. To examine a polymorphism of these genes in CAD susceptibility in patients and controls, PCR based genotyping assay was performed. For GST genes, frequency of GSTM1 null genotype among CAD affected group was significantly increased than in control group (P0.1). We found that neither XRCC1 Arg399Gln nor XRCC3 Thr241Met were associated with CAD risk. Obtained data suggests that GSTM1 null genotype carriers are more susceptible to CAD development.
Abstract: The presence of heavy metals in the environment
could constitute a hazard to food security and public health. These
can be accumulated in aquatic animals such as fish. Samples of four
popular brands of canned fish in the Iranian market (yellowfin tuna,
common Kilka, Kawakawa and longtail tuna) were analyzed for level
of Cr after wet digestion with acids using graphite furnace atomic
absorption spectrophotometry. The mean concentrations for Cr in the
different brands were: 2.57, 3.24, 3.16 and 1.65 μg/g for brands A, B,
C and D respectively. Significant differences were observed in the Cr
levels between all of the different brands of canned fish evaluated in
this study. The Cr concentrations for the varieties of canned fishes
were generally within the FAO/WHO, U.S. FDA and U.S. EPA
recommended limits for fish.
Abstract: Pairwise testing, which requires that every
combination of valid values of each pair of system factors be covered
by at lease one test case, plays an important role in software testing
since many faults are caused by unexpected 2-way interactions among
system factors. Although meta-heuristic strategies like simulated
annealing can generally discover smaller pairwise test suite, they may
cost more time to perform search, compared with greedy algorithms.
We propose a new method, improved Extremal Optimization (EO)
based on the Bak-Sneppen (BS) model of biological evolution, for
constructing pairwise test suites and define fitness function according
to the requirement of improved EO. Experimental results show that
improved EO gives similar size of resulting pairwise test suite and
yields an 85% reduction in solution time over SA.
Abstract: Both software applications and their development environment are becoming more and more distributed. This trend impacts not only the way software computes, but also how it looks. This article proposes a Human Computer Interface (HCI) template from three representative applications we have developed. These applications include a Multi-Agent System based software, a 3D Internet computer game with distributed game world logic, and a programming language environment used in constructing distributed neural network and its visualizations. HCI concepts that are common to these applications are described in abstract terms in the template. These include off-line presentation of global entities, entities inside a hierarchical namespace, communication and languages, reconfiguration of entity references in a graph, impersonation and access right, etc. We believe the metaphor that underlies an HCI concept as well as the relationships between a bunch of HCI concepts are crucial to the design of software systems and vice versa.
Abstract: Sputter deposition processes, especially for sputtering
from metal targets, are well investigated. For practical reasons, i.e.
for industrial processes, energetic considerations for sputter
deposition are useful in order to optimize the sputtering process. In
particular, for substrates at floating conditions it is required to obtain
energetic conditions during film growth that enables sufficient dense
metal films of good quality. The influence of ion energies, energy
density and momentum transfer is thus examined both for sputtering
at the target as well as during film growth. Different regimes
dominated by ion energy, energy density and momentum transfer
were identified by using different plasma sources and by varying
power input, pressure and bias voltage.
Abstract: Continuous-time delta-sigma analog digital converter (ADC) for radio frequency identification (RFID) complementary metal oxide semiconductor (CMOS) biosensor has been reported. This delta-sigma ADC is suitable for digital conversion of biosensor signal because of small process variation, and variable input range. As the input range of continuous-time switched current delta-sigma ADC (Dynamic range : 50 dB) can be limited by using current reference, amplification of biosensor signal is unnecessary. The input range is switched to wide input range mode or narrow input range mode by command of current reference. When the narrow input range mode, the input range becomes ± 0.8 V. The measured power consumption is 5 mW and chip area is 0.31 mm^2 using 1.2 um standard CMOS process. Additionally, automatic input range detecting system is proposed because of RFID biosensor applications.
Abstract: Considering toxicity of heavy metals and their
accumulation in domestic wastes, immobilization of lead and
cadmium is envisaged inside glass-ceramics. We particularly
focused this work on calcium-rich phases embedded in a
glassy matrix.
Glass-ceramics were synthesized from glasses doped with
12 wt% and 16 wt% of PbO or CdO. They were observed and
analyzed by Electron MicroProbe Analysis (EMPA) and
Analytical Scanning Electron Microscopy (ASEM). Structural
characterization of the samples was performed by powder XRay
Diffraction.
Diopside crystals of CaMgSi2O6 composition are shown to
incorporate significant amounts of cadmium (up to 9 wt% of
CdO). Two new crystalline phases are observed with very
high Cd or Pb contents: about 40 wt% CdO for the cadmiumrich
phase and near 60 wt% PbO for the lead-rich phase. We
present complete chemical and structural characterization of
these phases. They represent a promising way for the
immobilization of toxic elements like Cd or Pb since glass
ceramics are known to propose a “double barrier" protection
(metal-rich crystals embedded in a glass matrix) against metal
release in the environment.
Abstract: With data centers, end-users can realize the pervasiveness of services that will be one day the cornerstone of our lives. However, data centers are often classified as computing systems that consume the most amounts of power. To circumvent such a problem, we propose a self-adaptive weighted sum methodology that jointly optimizes the performance and power consumption of any given data center. Compared to traditional methodologies for multi-objective optimization problems, the proposed self-adaptive weighted sum technique does not rely on a systematical change of weights during the optimization procedure. The proposed technique is compared with the greedy and LR heuristics for large-scale problems, and the optimal solution for small-scale problems implemented in LINDO. the experimental results revealed that the proposed selfadaptive weighted sum technique outperforms both of the heuristics and projects a competitive performance compared to the optimal solution.
Abstract: This paper reports the tensile fracture location
characterizations of dissimilar friction stir welds between 5754
aluminium alloy and C11000 copper. The welds were produced using
three shoulder diameter tools; namely, 15, 18 and 25 mm by varying
the process parameters. The rotational speeds considered were 600,
950 and 1200 rpm while the feed rates employed were 50, 150 and
300 mm/min to represent the low, medium and high settings
respectively. The tensile fracture locations were evaluated using the
optical microscope to identify the fracture locations and were
characterized. It was observed that 70% of the tensile samples failed
in the Thermo Mechanically Affected Zone (TMAZ) of copper at the
weld joints. Further evaluation of the fracture surfaces of the pulled
tensile samples revealed that welds with low Ultimate Tensile
Strength either have defects or intermetallics present at their joint
interfaces.
Abstract: To learn about China-s future energy demand, this paper first proposed GM(1,1) model group based on recursive solutions of parameters estimation, setting up a general solving-algorithm of the model group. This method avoided the problems occurred on the past researches that remodeling, loss of information and large amount of calculation. This paper established respectively all-data-GM(1,1), metabolic GM(1,1) and new information GM (1,1)model according to the historical data of energy consumption in China in the year 2005-2010 and the added data of 2011, then modeling, simulating and comparison of accuracies we got the optimal models and to predict. Results showed that the total energy demand of China will be 37.2221 billion tons of equivalent coal in 2012 and 39.7973 billion tons of equivalent coal in 2013, which are as the same as the overall planning of energy demand in The 12th Five-Year Plan.
Abstract: Network reconfiguration in distribution system is realized by changing the status of sectionalizing switches to reduce the power loss in the system. This paper presents a new method which applies an artificial bee colony algorithm (ABC) for determining the sectionalizing switch to be operated in order to solve the distribution system loss minimization problem. The ABC algorithm is a new population based metaheuristic approach inspired by intelligent foraging behavior of honeybee swarm. The advantage of ABC algorithm is that it does not require external parameters such as cross over rate and mutation rate as in case of genetic algorithm and differential evolution and it is hard to determine these parameters in prior. The other advantage is that the global search ability in the algorithm is implemented by introducing neighborhood source production mechanism which is a similar to mutation process. To demonstrate the validity of the proposed algorithm, computer simulations are carried out on 14, 33, and 119-bus systems and compared with different approaches available in the literature. The proposed method has outperformed the other methods in terms of the quality of solution and computational efficiency.
Abstract: Aloe vera has been used worldwide both for
pharmaceutical, food, and cosmetic industries due to the plethora of
biological activities of some of its metabolites. The aim of this study
was to evaluate the antifungal and antioxidant activities of the leaf
extract. The antifungal activity was determined by the agar-well
diffusion method against plant and human fungal pathogens. The
methanol and ethanol portions of the extracts studied were more
bioactive than ethyl acetate portion. It was also observed that the
activity was more pronounced on plant pathogen than human
pathogen except Candida albicans. This is an indication that the
extract has the potential to treat plant fungal infections. The Aloe
extract showed the significant antioxidant activity by the DPPH
radical scavenging method. Therefore, the Aloe extract provided as
natural antioxidant has been used in health foods for medical and
preservative purposes.
Abstract: 17α-ethynylestradiol (EE2) is a synthetic estrogen
used as a key ingredient in an oral contraceptives pill. EE2 is an
endocrine disrupting compound, high in estrogenic potency.
Although EE2 exhibits low degree of biodegradability with common
microorganisms in wastewater treatment plants (WWTPs), this
compound can be biotransformed by ammonia-oxidizing bacteria
(AOB) via a co-metabolism mechanism in WWTPs. This study
aimed to investigate the effect of real wastewater on
biotransformation of EE2 by AOB. A preliminary experiment on the
effect of nitrite and pH levels on abiotic transformation of EE2
suggested that the abiotic transformation occurred at only pH
Abstract: In the past few years there is a change in the view of high performance applications and parallel computing. Initially such applications were targeted towards dedicated parallel machines. Recently trend is changing towards building meta-applications composed of several modules that exploit heterogeneous platforms and employ hybrid forms of parallelism. The aim of this paper is to propose a model of virtual parallel computing. Virtual parallel computing system provides a flexible object oriented software framework that makes it easy for programmers to write various parallel applications.
Abstract: The contamination of 15 ground water resources
of a selected region earmarked for the emergency supply
of population has been monitored. The resources have been selected
on the basis of previous assessment of natural conditions
and the exploitation of territory in their surroundings and infiltration
area. Two resources out of 15 have been excluded from further
exploitation, because they have not met some of the 72 assessed
hygienic indicators of extended analysis. The remaining 13 resources
have been the subject of health risk analysis in relation
to the contamination by arsenic, lead, cadmium, mercury, nickel and
manganese. The risk analysis proved that all 13 resources meet
health standards with regard to the above mentioned purposefully
selected elements and may thus be included into crisis plans. Water
quality of ground resources may be assessed in the same way
with regard to other contaminants.