Abstract: The response of King Abdulla Canal (KAC) water to the upgrade of As Samra Wastewater Treatment Plant which discharges its effluent to the Zarqa River is investigated. Time series quality data that extends between October 2005 and December 2009 obtained by a state of the art telemetric monitoring system were analyzed for COD, EC, TP and TN at two monitoring stations located upstream and downstream of the confluence of the Zarqa River with KAC. The samples- means and the t-test showed that there has been significant improvement in the quality of the KAC water for COD, and TP. However, the improvement in the TN was found statistically insignificant, whereas the EC of the KAC was unaffected by the upgrade. Comparing the selected parameters with the standards and guidelines for using treated wastewater in irrigation showed that the KAC water has improved towards meeting the required standards and guidelines for treated wastewater reuse in irrigation.
Abstract: In the Northern hemisphere, sheep reproduction is
seasonal (September-November). Among several natural factors
influencing the reproduction status of rams, we studied the daylight
length and temperature. Rams from different breeds were studied:
Merinos de Palas (half-precocious), Karakul de Botosani (halfbelated)
and Turcana (belated breed, low reproductive plasticity). In
Merinos de Palas, ejaculate volume during sexual repose is 51.3%
from normal quantity. When autumn climate was experimentally
induced, ejaculate volume reached 98.45% (Merinos), 94.97%
(Karakul) and 97.59% (Turcana). Semen density increased from
1.031-1.033 till 1.035 after exposition to artificial light and
temperature conditions. Spermatozoids mobility and sperm pH
improved, passing over 82% and 6.75, values identical to those in the
natural reproduction season. Behaviour analysis after
photoperiodicity indicated that over 83.3% Merinos and Karakul
males and all Turcana rams exteriorised normal and intense sexual
reflexes. Certain effort and reduced expenses brought rams in good
condition, producing higher quantity and quality sperm.
Abstract: Hydrodynamic pressures acting on upstream of concrete dams during an earthquake are an important factor in designing and assessing the safety of these structures in Earthquake regions. Due to inherent complexities, assessing exact hydrodynamic pressure is only feasible for problems with simple geometry. In this research, the governing equation of concrete gravity dam reservoirs with effect of fluid viscosity in frequency domain is solved and then compared with that in which viscosity is assumed zero. The results show that viscosity influences the reservoir-s natural frequency. In excitation frequencies near the reservoir's natural frequencies, hydrodynamic pressure has a considerable difference in compare to the results of non-viscose fluid.
Abstract: Mobile robots are used in a large field of scenarios,
like exploring contaminated areas, repairing oil rigs under water,
finding survivors in collapsed buildings, etc. Currently, there is no
unified intuitive user interface (UI) to control such complex mobile
robots. As a consequence, some scenarios are done without the
exploitation of experience and intuition of human teleoperators.
A novel framework has been developed to embed a flexible and
modular UI into a complete 3-D virtual reality simulation system.
This new approach wants to access maximum benefits of human
operators. Sensor information received from the robot is prepared for
an intuitive visualization. Virtual reality metaphors support the
operator in his decisions. These metaphors are integrated into a real
time stereo video stream. This approach is not restricted to any
specific type of mobile robot and allows for the operation of different
robot types with a consistent concept and user interface.
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: The evaluation of the question answering system is a major research area that needs much attention. Before the rise of domain-oriented question answering systems based on natural language understanding and reasoning, evaluation is never a problem as information retrieval-based metrics are readily available for use. However, when question answering systems began to be more domains specific, evaluation becomes a real issue. This is especially true when understanding and reasoning is required to cater for a wider variety of questions and at the same time achieve higher quality responses The research in this paper discusses the inappropriateness of the existing measure for response quality evaluation and in a later part, the call for new standard measures and the related considerations are brought forward. As a short-term solution for evaluating response quality of heterogeneous systems, and to demonstrate the challenges in evaluating systems of different nature, this research presents a black-box approach using observation, classification scheme and a scoring mechanism to assess and rank three example systems (i.e. AnswerBus, START and NaLURI).
Abstract: Swedish truck industry is investigating the possibility
for implementing the use of Compacted Graphite Iron (CGI) in their
heavy duty diesel engines. Compared to the alloyed gray iron used
today, CGI has superior mechanical properties but not as good
machinability. Another issue that needs to be addressed when
implementing CGI is the inhomogeneous microstructure when the
cast component has different section thicknesses, as in cylinder
blocks. Thinner sections results in finer pearlite, in the material, with
higher strength. Therefore an investigation on its influence on
machinability was needed. This paper focuses on the effect that
interlamellar distance in pearlite has on CGI machinability and
material physical properties. The effect of pearlite content and
nodularity is also examined. The results showed that interlamellar
distance in pearlite did not have as large effect on the material
physical properties or machinability as pearlite content. The paper
also shows the difficulties of obtaining a homogeneous
microstructure in inhomogeneous workpieces.
Abstract: A proposed small-signal model parameters for a pseudomorphic high electron mobility transistor (PHEMT) is presented. Both extrinsic and intrinsic circuit elements of a smallsignal model are determined using genetic algorithm (GA) as a stochastic global search and optimization tool. The parameters extraction of the small-signal model is performed on 200-μm gate width AlGaAs/InGaAs PHEMT. The equivalent circuit elements for a proposed 18 elements model are determined directly from the measured S- parameters. The GA is used to extract the parameters of the proposed small-signal model from 0.5 up to 18 GHz.
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: This paper presents a robust vehicle detection approach using Haar-like feature. It is possible to get a strong edge feature from this Haar-like feature. Therefore it is very effective to remove the shadow of a vehicle on the road. And we can detect the boundary of vehicles accurately. In the paper, the vehicle detection algorithm can be divided into two main steps. One is hypothesis generation, and the other is hypothesis verification. In the first step, it determines vehicle candidates using features such as a shadow, intensity, and vertical edge. And in the second step, it determines whether the candidate is a vehicle or not by using the symmetry of vehicle edge features. In this research, we can get the detection rate over 15 frames per second on our embedded system.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: Studies revealing the positive relationship between
trade and income are often criticized with the argument that
“development should mean more than rising incomes". Taking this
argument as a base and utilizing panel data, Davies and Quinlivan [1]
have demonstrated that increases in trade are positively associated
with future increases in social welfare as measured by the Human
Development Index (HDI). The purpose of this study is twofold:
Firstly, utilizing an income based country classification; it is aimed
to investigate whether the positive association between foreign trade
and HDI is valid within all country groups. Secondly, keeping the
same categorization as a base; it is aimed to reveal whether the
positive link between trade and HDI still exists when the income
components of the index are excluded. Employing a panel data
framework of 106 countries, this study reveals that the positive link
between trade and human development is valid only for high and
medium income countries. Moreover, the positive link between trade
and human development diminishes in lower-medium income
countries when only non-income components of the index are taken
into consideration.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: In the article there have been revealed the properties
of designing the research teaching the military masters and in the context it has been offered the program of mastering by the masters
military men the methodology of research work, in the course of practical teaching activity there has been considered the developed
and approbated model of organization of the process of mastering by the masters the methodology of research work. As a whole, the research direction of master preparation leaves its
sign to the content of education, forms of organization of educational
process, scientific work of masters. In this connection the offered in
the article properties of organization of research teaching and a model
of organization of mastering by the masters military men the methodology of research work can be taken into account when
designing the content of master preparation.
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.
Abstract: In this study, it is investigated the stability boundary of
Functionally Graded (FG) panel under the heats and supersonic
airflows. Material properties are assumed to be temperature
dependent, and a simple power law distribution is taken. First-order
shear deformation theory (FSDT) of plate is applied to model the
panel, and the von-Karman strain- displacement relations are
adopted to consider the geometric nonlinearity due to large
deformation. Further, the first-order piston theory is used to model the
supersonic aerodynamic load acting on a panel and Rayleigh damping
coefficient is used to present the structural damping. In order to find a
critical value of the speed, linear flutter analysis of FG panels is
performed. Numerical results are compared with the previous works,
and present results for the temperature dependent material are
discussed in detail for stability boundary of the panel with various
volume fractions, and aerodynamic pressures.