Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: Dynamic models of power converters are normally
time-varying because of their switching actions. Several approaches
are applied to analyze the power converters to achieve the timeinvariant
models suitable for system analysis and design via the
classical control theory. The paper presents how to derive dynamic
models of the power system consisting of a three-phase controlled
rectifier feeding an uncontrolled buck converter by using the
combination between the well known techniques called the DQ and
the generalized state-space averaging methods. The intensive timedomain
simulations of the exact topology model are used to support
the accuracies of the reported model. The results show that the
proposed model can provide good accuracies in both transient and
steady-state responses.
Abstract: Yogurts are prepared by fermenting milk with bacterial cultures consisting of a mixture of Streptococcus ssp. thermophilus and Lactobacillus delbrueckii ssp. bulgaricus. The main aim of this investigation was to develop a majority goat yogurt, with the addition of sheep milk in order to have a final product with good physicochemical quality properties and sensorial attributes. Four types of yogurts were prepared presenting the following proportion of goat and sheep milk respectively: C100 – 100%; C80 – 80%/20%; C60 – 60%/40%; C50 – 50%/50%. The goat milk was from the Serrana Jarmelista breed and the sheep milk from the Serra da Estrela breed. The inclusion of sheep milk improved attractiveness to consumers, and it also improved the nutritional value of the product, mainly the fatty acid and mineral contents. The C50 yogurt was preferred by 28% of the panellists, followed by the C100 with 16% and the commercial cow yogurt was 40% of preferences.
Abstract: A mathematical model for the hydrodynamics of a
surface water treatment pilot plant was developed and validated by
the determination of the residence time distribution (RTD) for the
main equipments of the unit. The well known models of ideal/real
mixing, ideal displacement (plug flow) and (one-dimensional axial)
dispersion model were combined in order to identify the structure
that gives the best fitting of the experimental data for each equipment
of the pilot plant. RTD experimental results have shown that pilot
plant hydrodynamics can be quite well approximated by a
combination of simple mathematical models, structure which is
suitable for engineering applications. Validated hydrodynamic
models will be further used in the evaluation and selection of the
most suitable coagulation-flocculation reagents, optimum operating
conditions (injection point, reaction times, etc.), in order to improve
the quality of the drinking water.
Abstract: In this study, oxidative steam reforming of methanol (OSRM) over a Au/CeO2–Fe2O3 catalyst prepared by a depositionprecipitation (DP) method was studied to produce hydrogen in order to feed a Proton Exchange Membrane Fuel Cell (PEMFC). The support (CeO2, Fe2O3, and CeO2–Fe2O3) were prepared by precipitation and co-precipitation methods. The impact of the support composition on the catalytic performance was studied by varying the Ce/(Ce+Fe) atomic ratio, it was found that the 1%Au/CF(0.25) calcined at 300 °C exhibited the highest catalytic activity in the whole temperature studied. In addition, the effect of Au content was investigated and 3%Au/CF(0.25) exhibited the highest activity under the optimum condition in the temperature range of 200 °C to 400 °C. The catalysts were characterized by various techniques: XRD, TPR, XRF, and UV-vis.
Abstract: Postmenopausal osteoporosis is a disorder
characterized by the progressive bone loss induced by estrogen
deficiency in postmenopausal women. This imbalance affects
calcium–phosphate metabolism and results in secondary
hyperparathyroidism. Purariae Radix (PR), the root of P. lobata
(Wild.) Ohwi, is one of the earliest medicinal herbs employed in
ancient China. PR contains a high quantity of isoflavones and their
glycosides, which are regarded as phytoestrogen. Few investigations
of PR are related to its osteoprotective effects. The present study is
designed to administer PR water extract to ovariectomized (OVX)
female rats, for the investigation of its possibly protective actions on
bone and to delineate the potential mechanisms involved. Our results
demonstrated that long-term treatment of PR could not significantly
improve bone properties, whereas it greatly ameliorated the condition
of secondary hyperparathyroidism induced by ovariectomy in those
animals. PR might be useful as alternative regimen for protecting
against postmenopausal bone loss.
Abstract: In this work, we present for the first time in our
perception an efficient digital watermarking scheme for mpeg audio
layer 3 files that operates directly in the compressed data domain,
while manipulating the time and subband/channel domain. In
addition, it does not need the original signal to detect the watermark.
Our scheme was implemented taking special care for the efficient
usage of the two limited resources of computer systems: time and
space. It offers to the industrial user the capability of watermark
embedding and detection in time immediately comparable to the real
music time of the original audio file that depends on the mpeg
compression, while the end user/audience does not face any artifacts
or delays hearing the watermarked audio file. Furthermore, it
overcomes the disadvantage of algorithms operating in the PCMData
domain to be vulnerable to compression/recompression attacks,
as it places the watermark in the scale factors domain and not in the
digitized sound audio data. The strength of our scheme, that allows it
to be used with success in both authentication and copyright
protection, relies on the fact that it gives to the users the enhanced
capability their ownership of the audio file not to be accomplished
simply by detecting the bit pattern that comprises the watermark
itself, but by showing that the legal owner knows a hard to compute
property of the watermark.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.
Abstract: Ultrasound is useful in demonstrating bone mineral
density of regenerating osseous tissue as well as structural alterations.
A proposed ultrasound method, which included ultrasonography and
acoustic parameters measurement, was employed to evaluate its
efficacy in monitoring the bone callus changes in a rabbit tibial
distraction osteogenesis (DO) model.
The findings demonstrated that ultrasonographic images depicted
characteristic changes of the bone callus, typical of histology findings,
during the distraction phase. Follow-up acoustic parameters
measurement of the bone callus, including speed of sound, reflection
and attenuation, showed significant linear changes over time during
the distraction phase. The acoustic parameters obtained during the
distraction phase also showed moderate to strong correlation with
consolidated bone callus density and micro-architecture measured by
micro-computed tomography at the end of the consolidation phase.
The results support the preferred use of ultrasound imaging in the
early monitoring of bone callus changes during DO treatment.
Abstract: Command and Control (C2) system and its interfacethe
Common Operational Picture (COP) are main means that
supports commander in its decision making process. COP contains
information about friendly and enemy unit positions. The friendly
position is gathered via tactical network. In the case of tactical
network failure the information about units are not available. The
tactical simulator can be used as a tool that is capable to predict
movements of units in respect of terrain features. Article deals with
an experiment that was based on Czech C2 system that is in the case
of connectivity lost fed by VR Forces simulator. Article analyzes
maximum time interval in which the position created by simulator is
still usable and truthful for commander in real time.
Abstract: This paper presents functionality of negotiation agent
on value-based design decision. The functionality is based on the
characteristics of the system and goal specification. A Prometheus
Design Tool model was used for developing the system. Group
functionality will be the attribute for negotiation agents, which
comprises a coordinator agent and decision- maker agent. The results
of the testing of the system to a building system selection on valuebased
decision environment are also presented.
Abstract: To simulate expected climate change, we implemented a two-factor (temperature and soil moisture) field design in a forest in Ontario, Canada. To manipulate moisture input, we erected rain-exclusion structures. Under each structure, plots were watered with one of three treatments and thermally controlled with three heat treatments to simulate changes in air temperature and rainfall based on the climate model (GCM) predictions for the study area. Environmental conditions (including untreated controls) were monitored tracking air temperature, soil temperature, soil moisture, and photosynthetically active radiation. We measured rainfall and relative humidity at the site outside the rain-exclusion structures. Analyses of environmental conditions demonstrates that the temperature manipulation was most effective at maintaining target temperature during the early part of the growing season, but it was more difficult to keep the warmest treatment at 5º C above ambient by late summer. Target moisture regimes were generally achieved however incoming solar radiation was slightly attenuated by the structures.
Abstract: In the context of channel coding, the Generalized Belief Propagation (GBP) is an iterative algorithm used to recover the transmission bits sent through a noisy channel. To ensure a reliable transmission, we apply a map on the bits, that is called a code. This code induces artificial correlations between the bits to send, and it can be modeled by a graph whose nodes are the bits and the edges are the correlations. This graph, called Tanner graph, is used for most of the decoding algorithms like Belief Propagation or Gallager-B. The GBP is based on a non unic transformation of the Tanner graph into a so called region-graph. A clear advantage of the GBP over the other algorithms is the freedom in the construction of this graph. In this article, we explain a particular construction for specific graph topologies that involves relevant performance of the GBP. Moreover, we investigate the behavior of the GBP considered as a dynamic system in order to understand the way it evolves in terms of the time and in terms of the noise power of the channel. To this end we make use of classical measures and we introduce a new measure called the hyperspheres method that enables to know the size of the attractors.
Abstract: Lossless compression schemes with secure
transmission play a key role in telemedicine applications that helps in
accurate diagnosis and research. Traditional cryptographic algorithms
for data security are not fast enough to process vast amount of data.
Hence a novel Secured lossless compression approach proposed in
this paper is based on reversible integer wavelet transform, EZW
algorithm, new modified runlength coding for character
representation and selective bit scrambling. The use of the lifting
scheme allows generating truly lossless integer-to-integer wavelet
transforms. Images are compressed/decompressed by well-known
EZW algorithm. The proposed modified runlength coding greatly
improves the compression performance and also increases the
security level. This work employs scrambling method which is fast,
simple to implement and it provides security. Lossless compression
ratios and distortion performance of this proposed method are found
to be better than other lossless techniques.
Abstract: A product goes through various processes in a production flow which is also known as assembly line in manufacturing process management. Toyota created a new concept which is known as lean concept in manufacturing industry. Today it is the leading model in manufacturing plants through the globe. The linear walking worker assembly line is a flexible assembly system where each worker travels down the line carrying out each assembly task at each station; and each worker accomplishes the assembly of a unit from start to finish. This paper attempts to combine the flexibility of the walking worker and lean in order to quantify the benefits from applying the shop floor principles of lean management.
Abstract: Response surface methodology was used for
quantitative investigation of water and solids transfer during osmotic
dehydration of beetroot in aqueous solution of salt. Effects of
temperature (25 – 45oC), processing time (30–150 min), salt
concentration (5–25%, w/w) and solution to sample ratio (5:1 – 25:1)
on osmotic dehydration of beetroot were estimated. Quadratic
regression equations describing the effects of these factors on the
water loss and solids gain were developed. It was found that effects
of temperature and salt concentrations were more significant on the
water loss than the effects of processing time and solution to sample
ratio. As for solids gain processing time and salt concentration were
the most significant factors. The osmotic dehydration process was
optimized for water loss, solute gain, and weight reduction. The
optimum conditions were found to be: temperature – 35oC,
processing time – 90 min, salt concentration – 14.31% and solution
to sample ratio 8.5:1. At these optimum values, water loss, solid gain
and weight reduction were found to be 30.86 (g/100 g initial sample),
9.43 (g/100 g initial sample) and 21.43 (g/100 g initial sample)
respectively.
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.
Abstract: In production planning (PP) periods with excess capacity
and growing demand, the manufacturers have two options to use the excess capacity. First, it could do more changeovers and thus reduce lot sizes, inventories, and inventory costs. Second, it could produce in excess of demand in the period and build additional inventory that can be used to satisfy future demand increments, thus
delaying the purchase of the next machine that is required to meet the growth in demand. In this study we propose an enhanced supply
chain planning model with flexible planning capability. In addition, a 3D supply chain planning system is illustrated.