Abstract: This paper attempts to explain response components of Electrovestibulography (EVestG) using a computer simulation of a three-canal model of the vestibular system. EVestG is a potentially new diagnostic method for Meniere's disease. EVestG is a variant of Electrocochleography (ECOG), which has been used as a standard method for diagnosing Meniere's disease - it can be used to measure the SP/AP ratio, where an SP/AP ratio greater than 0.4-0.5 is indicative of Meniere-s Disease. In EVestG, an applied head tilt replaces the acoustic stimulus of ECOG. The EVestG output is also an SP/AP type plot, where SP is the summing potential, and AP is the action potential amplitude. AP is thought of as being proportional to the size of a population of afferents in an excitatory neural firing state. A simulation of the fluid volume displacement in the vestibular labyrinth in response to various types of head tilts (ipsilateral, backwards and horizontal rotation) was performed, and a simple neural model based on these simulations developed. The simple neural model shows that the change in firing rate of the utricle is much larger in magnitude than the change in firing rates of all three semi-circular canals following a head tilt (except in a horizontal rotation). The data suggests that the change in utricular firing rate is a minimum 2-3 orders of magnitude larger than changes in firing rates of the canals during ipsilateral/backward tilts. Based on these results, the neural response recorded by the electrode in our EVestG recordings is expected to be dominated by the utricle in ipsilateral/backward tilts (It is important to note that the effect of the saccule and efferent signals were not taken into account in this model). If the utricle response dominates the EVestG recordings as the modeling results suggest, then EVestG has the potential to diagnose utricular hair cell damage due to a viral infection (which has been cited as one possible cause of Meniere's Disease).
Abstract: The objectives of this research were to compare the success of SME registered in Nakorn Pathom Province divided in personal data also to study the relations between the innovation knowledge and capability and the success of SME registered in Nakorn Pathom Province and to study the relations between the work efficiency and the success of SME registered in Nakorn Pathom Province. A questionnaire was utilized as a tool to collect data. Statistics utilized in this research included frequency, percentage, mean, standard deviation, and multiple regression analysis. Data were analyzed by using Statistical Package for the Social Sciences.The findings revealed that the majority of respondents were male with the age between 25-34 years old, hold undergraduate degree, married and stay together. The average income of respondents was between 10,001-20,000 baht. It also found that in terms of innovation knowledge and capability, there were two variables had an influence on the amount of innovation knowledge and capability, innovation evaluation which were physical characteristic and innovation process.
Abstract: Set covering problem is a classical problem in
computer science and complexity theory. It has many applications,
such as airline crew scheduling problem, facilities location problem,
vehicle routing, assignment problem, etc. In this paper, three
different techniques are applied to solve set covering problem.
Firstly, a mathematical model of set covering problem is introduced
and solved by using optimization solver, LINGO. Secondly, the
Genetic Algorithm Toolbox available in MATLAB is used to solve
set covering problem. And lastly, an ant colony optimization method
is programmed in MATLAB programming language. Results
obtained from these methods are presented in tables. In order to
assess the performance of the techniques used in this project, the
benchmark problems available in open literature are used.
Abstract: Existing image-based virtual reality applications
allow users to view image-based 3D virtual environment in a more
interactive manner. User could “walkthrough"; looks left, right, up
and down and even zoom into objects in these virtual worlds of
images. However what the user sees during a “zoom in" is just a
close-up view of the same image which was taken from a distant.
Thus, this does not give the user an accurate view of the object from
the actual distance. In this paper, a simple technique for zooming in
an object in a virtual scene is presented. The technique is based on
the 'hotspot' concept in existing application. Instead of navigation
between two different locations, the hotspots are used to focus into
an object in the scene. For each object, several hotspots are created.
A different picture is taken for each hotspot. Each consecutive
hotspot created will take the user closer to the object. This will
provide the user with a correct of view of the object based on his
proximity to the object. Implementation issues and the relevance of
this technique in potential application areas are highlighted.
Abstract: This research presents a fuzzy multi-objective model
for a machine selection problem in a flexible manufacturing system
of a tire company. Two main objectives are minimization of an
average machine error and minimization of the total setup time.
Conventionally, the working team uses trial and error in selecting a
pressing machine for each task due to the complexity and constraints
of the problem. So, both objectives may not satisfy. Moreover, trial
and error takes a lot of time to get the final decision. Therefore, in
this research preemptive fuzzy goal programming model is developed
for solving this multi-objective problem. The proposed model can
obtain the appropriate results that the Decision Making (DM) is
satisfied for both objectives. Besides, alternative choice can be easily
generated by varying the satisfaction level. Additionally, decision
time can be reduced by using the model, which includes all
constraints of the system to generate the solutions. A numerical
example is also illustrated to show the effectiveness of the proposed
model.
Abstract: There exists an injective, information-preserving function
that maps a semantic network (i.e a directed labeled network)
to a directed network (i.e. a directed unlabeled network). The edge
label in the semantic network is represented as a topological feature
of the directed network. Also, there exists an injective function that
maps a directed network to an undirected network (i.e. an undirected
unlabeled network). The edge directionality in the directed network
is represented as a topological feature of the undirected network.
Through function composition, there exists an injective function that
maps a semantic network to an undirected network. Thus, aside from
space constraints, the semantic network construct does not have any
modeling functionality that is not possible with either a directed
or undirected network representation. Two proofs of this idea will
be presented. The first is a proof of the aforementioned function
composition concept. The second is a simpler proof involving an
undirected binary encoding of a semantic network.
Abstract: Bandung city center can be deemed as economic, social and cultural center. However the city center suffers from deterioration. The retail activities tend to shift outward the city center. Numerous idyllic residences changed into business premises in two villages situated in the north part of the city during 1990s, especially after a new highway and flyover opened. According to space syntax theory, the pattern of spatial integration in the urban grid is a prime determinant of movement patterns in the system. The syntactic analysis results show the flyover has insignificant influence on street network in the city center. However the flyover has been generating a major difference in the new commercial area since it has become relatively as strategic as the city center. Besides street network, local government policy, rapid private motorization and particular condition of each site also played important roles in encouraging the current commercial areas to flourish.
Abstract: This paper proposes, for the first time, how the
challenges facing the guard-band designs including the margin
assist-circuits scheme for the screening-test in the coming process
generations should be addressed. The increased screening error
impacts are discussed based on the proposed statistical analysis
models. It has been shown that the yield-loss caused by the
misjudgment on the screening test would become 5-orders of
magnitude larger than that for the conventional one when the
amplitude of random telegraph noise (RTN) caused variations
approaches to that of random dopant fluctuation. Three fitting methods
to approximate the RTN caused complex Gamma mixtures
distributions by the simple Gaussian mixtures model (GMM) are
proposed and compared. It has been verified that the proposed
methods can reduce the error of the fail-bit predictions by 4-orders of
magnitude.
Abstract: This paper presents work characterizing finite element
performance boundaries within which live, interactive finite element
modeling is feasible on current and emerging systems. These results
are based on wide-ranging tests performed using a prototype finite
element program implemented specifically for this study, thereby enabling
the unified investigation of numerous direct and iterative solver
strategies and implementations in a variety of modeling contexts.
The results are intended to be useful for researchers interested in
interactive analysis by providing baseline performance estimates, to
give guidance in matching solution strategies to problem domains,
and to spur further work addressing the challenge of extending the
present boundaries.
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: Arsenic in the sediments of the ash lagoons of the coal-fired power plant in Pagbilao, Quezon Province in the Philippines was sequentially extracted to determine its potential for leaching to the groundwater and the adjacent marine environment. Results show that 89% of the As is bound to the quasi-crystalline Fe/Mn oxides and hydroxide matrix in the sediments, whereas, the adsorbed and exchangeable As hosted by the clay minerals, representing those that are easiest to release from the sediment matrix, is below 10% of the acid leachable As. These As in these sediment matrices represent the possible maximum amount of As that can be released and supplied to the groundwater and the adjacent marine environment. Of the 89% reducible As, up to 4% is associated with the easily reducible variety, whereas, the rest is more strongly bonded by the moderately reducible variety. Based on the long-term As content of the lagoon water, the average desorption rate of As is calculated to be very low -- 0.3-0.5% on the average and 0.6% on the maximum. This indicates that As is well-fixed by its sediment matrices in the ash lagoon, attenuating the influx of As into the adjacent groundwater and marine environments.
Abstract: The experiments were performed in a batch set up
under different concentrations of Cu (II) (0.2 g.l-1 to 0.9 g.l-1), pH (4-
6), temperatures (20oC – 40oC) with varying teak leaves powder (as
biosorbent) dosage of 0.3 g.l-1 to 0.5 g.l-1. The kinetics of interactions
were tested with pseudo first order Lagergran equation and the value
for k1 was found to be 6.909 x 10-3 min-1. The biosorption data gave
a good fit with Langmuir and Fruendlich isotherms and the Langmuir
monolayer capacity (qm) was found to be 166.78 mg. g-1. Similarly
the Freundlich adsorption capacity (Kf) was estimated as 2.49 l g-1.
The mean values of the thermodynamic parameters ΔH, ΔS, and ΔG
were -62.42 KJ. mol-1, -0.219 KJ.mol-1 K-1 and -1.747 KJ.mol-1 at
293 K from a solution containing 0.4 g l-1 of Cu(II) showing the
biosorption to be thermodynamically favourable. These results show
good potentiality of using teak leaves as a biosorbent for the removal
of Cu(II) from aqueous solutions.
Abstract: Group key management is an important functional
building block for any secure multicast architecture.
Thereby, it has been extensively studied in the literature.
In this paper we present relevant group key management
protocols. Then, we compare them against some pertinent
performance criteria.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: A potential flow model is used to study the unsteady
flow past two airfoils in configuration, each of which is suddenly set
into motion. The airfoil bound vortices are modeled using lumped
vortex elements and the wake behind the airfoil is modeled by discrete
vortices. This consists of solving a steady state flow problem at each
time-step where unsteadiness is incorporated through the “zero normal
flow on a solid surface" boundary condition at every time instant.
Additionally, along with the “zero normal flow on a solid surface"
boundary condition Kelvin-s condition is used to compute the strength
of the latest wake vortex shed from the trailing edge of the airfoil.
Location of the wake vortices is updated at each time-step to get the
wake shape at each time instant. Results are presented to show the
effect of airfoil-airfoil interaction and airfoil-wake interaction on the
aerodynamic characteristics of each airfoil.
Abstract: Background Contact lens (CL) wear can cause
changes in blinking and corneal staining. Aims and Objectives To
determine the effects of CL materials (HEMA and SiHy) on
spontaneous blink rate, blinking patterns and corneal staining after 2
months of wear. Methods Ninety subjects in 3 groups (control,
HEMA and SiHy) were assessed at baseline and 2-months. Blink rate
was recorded using a video camera. Blinking patterns were assessed
with digital camera and slit lamp biomicroscope. Corneal staining
was graded using IER grading scale Results There were no significant
differences in all parameters at baseline. At 2 months, CL wearers
showed significant increment in average blink rate (F1.626, 47.141 =
7.250, p = 0.003; F2,58 = 6.240, p = 0.004) and corneal staining (χ2
2,
n=30 = 31.921, p < 0.001; χ2
2, n=30 = 26.909, p < 0.001). Conclusion
Blinking characteristics and corneal staining were not influence by
soft CL materials.
Abstract: This paper propose a new circuit design which
monitor total leakage current during standby mode and generates the
optimal reverse body bias voltage, by using the adaptive body bias
(ABB) technique to compensate die-to-die parameter variations.
Design details of power monitor are examined using simulation
framework in 65nm and 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 10 μW for 32nm technology and
about 12 μW for 65nm technology at the same power supply voltage
as the core power supply. Moreover the results show that our
proposed circuit design is not far sensitive to the temperature
variations and also process variations. Besides, uses the simple
blocks which offer good sensitivity, high speed, the continuously
feedback loop.
Abstract: This research uses computational linguistics, an area of study that employs a computer to process natural language, and aims at discerning the patterns that exist in declarative sentences used in technical texts. The approach is mathematical, and the focus is on instructional texts found on web pages. The technique developed by the author and named the MAYA Semantic Technique is used here and organized into four stages. In the first stage, the parts of speech in each sentence are identified. In the second stage, the subject of the sentence is determined. In the third stage, MAYA performs a frequency analysis on the remaining words to determine the verb and its object. In the fourth stage, MAYA does statistical analysis to determine the content of the web page. The advantage of the MAYA Semantic Technique lies in its use of mathematical principles to represent grammatical operations which assist processing and accuracy if performed on unambiguous text. The MAYA Semantic Technique is part of a proposed architecture for an entire web-based intelligent tutoring system. On a sample set of sentences, partial semantics derived using the MAYA Semantic Technique were approximately 80% accurate. The system currently processes technical text in one domain, namely Cµ programming. In this domain all the keywords and programming concepts are known and understood.
Abstract: Like other external sorting algorithms, the presented
algorithm is a two step algorithm including internal and external
steps. The first part of the algorithm is like the other similar
algorithms but second part of that is including a new easy
implementing method which has reduced the vast number of inputoutput
operations saliently. As decreasing processor operating time
does not have any effect on main algorithm speed, any improvement
in it should be done through decreasing the number of input-output
operations. This paper propose an easy algorithm for choose the
correct record location of the final list. This decreases the time
complexity and makes the algorithm faster.