Abstract: The feasibility of employing solar radiation for
enhanced Fenton process in degradation of combined chlorpyrifos,
cypermethrin and chlorothalonil pesticides was examined. The effect
of various operating conditions of the process on biodegradability
improvement and mineralization of the pesticides were also
evaluated. The optimum operating conditions for treatment of
aqueous solution containing 100, 50 and 250 mg L-1 chlorpyrifos
cypermethrin and chlorothalonil, respectively were observed to be
H2O2/COD molar ratio 2, H2O2/Fe2+ molar ratio 25 and pH 3. Under
the optimum operating conditions, complete degradation of the
pesticides occurred in 1 min. Biodegradability (BOD5/COD)
increased from zero to 0.36 in 60 min, and COD and TOC removal
were 74.19 and 58.32%, respectively in 60 min. Due to
mineralization of organic carbon, decrease in ammonia-nitrogen from
22 to 4.3 mg L-1 and increase in nitrate from 0.7 to 18.1 mg L-1 in
60 min were recorded. The study indicated that solar photo-Fenton
process can be used for pretreatment of chlorpyrifos, cypermethrin
and chlorothalonil pesticides in aqueous solution for further
biological treatment.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: We propose a decoy-pulse protocol for frequency-coded implementation of B92 quantum key distribution protocol. A direct extension of decoy-pulse method to frequency-coding scheme results in security loss as an eavesdropper can distinguish between signal and decoy pulses by measuring the carrier photon number without affecting other statistics. We overcome this problem by optimizing the ratio of carrier photon number of decoy-to-signal pulse to be as close to unity as possible. In our method the switching between signal and decoy pulses is achieved by changing the amplitude of RF signal as opposed to modulating the intensity of optical signal thus reducing system cost. We find an improvement by a factor of 100 approximately in the key generation rate using decoy-state protocol. We also study the effect of source fluctuation on key rate. Our simulation results show a key generation rate of 1.5×10-4/pulse for link lengths up to 70km. Finally, we discuss the optimum value of average photon number of signal pulse for a given key rate while also optimizing the carrier ratio.
Abstract: The Chinese Postman Problem (CPP) is one of the
classical problems in graph theory and is applicable in a wide range
of fields. With the rapid development of hybrid systems and model
based testing, Chinese Postman Problem with Time Dependent Travel
Times (CPPTDT) becomes more realistic than the classical problems.
In the literature, we have proposed the first integer programming
formulation for the CPPTDT problem, namely, circuit formulation,
based on which some polyhedral results are investigated and a cutting
plane algorithm is also designed. However, there exists a main drawback:
the circuit formulation is only available for solving the special
instances with all circuits passing through the origin. Therefore, this
paper proposes a new integer programming formulation for solving
all the general instances of CPPTDT. Moreover, the size of the circuit
formulation is too large, which is reduced dramatically here. Thus, it
is possible to design more efficient algorithm for solving the CPPTDT
in the future research.
Abstract: As the Computed Tomography(CT) requires normally
hundreds of projections to reconstruct the image, patients are exposed
to more X-ray energy, which may cause side effects such as cancer.
Even when the variability of the particles in the object is very less,
Computed Tomography requires many projections for good quality
reconstruction. In this paper, less variability of the particles in an
object has been exploited to obtain good quality reconstruction.
Though the reconstructed image and the original image have same
projections, in general, they need not be the same. In addition
to projections, if a priori information about the image is known,
it is possible to obtain good quality reconstructed image. In this
paper, it has been shown by experimental results why conventional
algorithms fail to reconstruct from a few projections, and an efficient
polynomial time algorithm has been given to reconstruct a bi-level
image from its projections along row and column, and a known sub
image of unknown image with smoothness constraints by reducing the
reconstruction problem to integral max flow problem. This paper also
discusses the necessary and sufficient conditions for uniqueness and
extension of 2D-bi-level image reconstruction to 3D-bi-level image
reconstruction.
Abstract: Environment both endowed and built are essential for
tourism. However tourism and environment maintains a complex
relationship, where in most cases environment is at the receiving end.
Many tourism development activities have adverse environmental
effects, mainly emanating from construction of general infrastructure
and tourism facilities. These negative impacts of tourism can lead to
the destruction of precious natural resources on which it depends.
These effects vary between locations; and its effect on a hill
destination is highly critical. This study aims at developing a
Sustainable Tourism Planning Model for an environmentally
sensitive tourism destination in Kerala, India. Being part of the
Nilgiri mountain ranges, Munnar falls in the Western Ghats, one of
the biological hotspots in the world. Endowed with a unique high
altitude environment Munnar inherits highly significant ecological
wealth. Giving prime importance to the protection of this ecological
heritage, the study proposes a tourism planning model with resource
conservation and sustainability as the paramount focus. Conceiving a
novel approach towards sustainable tourism planning, the study
proposes to assess tourism attractions using Ecological Sensitivity
Index (ESI) and Tourism Attractiveness Index (TAI). Integration of
these two indices will form the Ecology – Tourism Matrix (ETM),
outlining the base for tourism planning in an environmentally
sensitive destination. The ETM Matrix leads to a classification of
tourism nodes according to its Conservation Significance and
Tourism Significance. The spatial integration of such nodes based on
the Hub & Spoke Principle constitutes sub – regions within the STZ.
Ensuing analyses lead to specific guidelines for the STZ as a whole,
specific tourism nodes, hubs and sub-regions. The study results in a
multi – dimensional output, viz., (1) Classification system for tourism
nodes in an environmentally sensitive region/ destination (2)
Conservation / Tourism Development Strategies and Guidelines for
the micro and macro regions and (3) A Sustainable Tourism Planning
Tool particularly for Ecologically Sensitive Destinations, which can
be adapted for other destinations as well.
Abstract: This paper is concerned with the application of the vision control algorithm for robot's point placement task in discontinuous trajectory caused by obstacle. The presented vision control algorithm consists of four models, which are the robot kinematic model, vision system model, parameters estimation model, and robot joint angle estimation model.When the robot moves toward a target along discontinuous trajectory, several types of obstacles appear in two obstacle regions. Then, this study is to investigate how these changes will affect the presented vision control algorithm.Thus, the practicality of the vision control algorithm is demonstrated experimentally by performing the robot's point placement task in discontinuous trajectory by obstacle.
Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: Li1.5Al0.5Ti1.5 (PO4)3(LATP) has received much
attention as a solid electrolyte for lithium batteries. In this study, the
LATP solid electrolyte is prepared by the co-precipitation method
using Li3PO4 as a Li source. The LATP is successfully prepared and
the Li ion conductivities of bulk (inner crystal) and total (inner crystal
and grain boundary) are 1.1 × 10-3 and 1.1 × 10-4 S cm-1, respectively.
These values are comparable to the reported values, in which Li2C2O4
is used as the Li source. It is conclude that the LATP solid electrolyte
can be prepared by the co-precipitation method using Li3PO4 as the Li
source and this procedure has an advantage in mass production over
previous procedure using Li2C2O4 because Li3PO4 is lower price
reagent compared with Li2C2O4.
Abstract: Computed tomography and laminography are heavily investigated in a compressive sensing based image reconstruction framework to reduce the dose to the patients as well as to the radiosensitive devices such as multilayer microelectronic circuit boards. Nowadays researchers are actively working on optimizing the compressive sensing based iterative image reconstruction algorithm to obtain better quality images. However, the effects of the sampled data’s properties on reconstructed the image’s quality, particularly in an insufficient sampled data conditions have not been explored in computed laminography. In this paper, we investigated the effects of two data properties i.e. sampling density and data incoherence on the reconstructed image obtained by conventional computed laminography and a recently proposed method called spherical sinusoidal scanning scheme. We have found that in a compressive sensing based image reconstruction framework, the image quality mainly depends upon the data incoherence when the data is uniformly sampled.
Abstract: In this paper we present a way of controlling the
concurrent access to data in a distributed application using the
Pessimistic Offline Lock design pattern. In our case, the application
processes a complex entity, which contains in a hierarchical structure
different other entities (objects). It will be shown how the complex
entity and the contained entities must be locked in order to control
the concurrent access to data.
Abstract: This paper describes the design and results of FROID,
an outbound intrusion detection system built with agent technology
and supported by an attacker-centric ontology. The prototype
features a misuse-based detection mechanism that identifies remote
attack tools in execution. Misuse signatures composed of attributes
selected through entropy analysis of outgoing traffic streams and
process runtime data are derived from execution variants of attack
programs. The core of the architecture is a mesh of self-contained
detection cells organized non-hierarchically that group agents in a
functional fashion. The experiments show performance gains when
the ontology is enabled as well as an increase in accuracy achieved
when correlation cells combine detection evidence received from
independent detection cells.
Abstract: Digital watermarking is the process of embedding
information into a digital signal which can be used in DRM (digital
rights managements) system. The visible watermark (often called logo)
can indicate the owner of the copyright which can often be seen in the
TV program and protects the copyright in an active way. However,
most of the schemes do not consider the visible watermark removing
process. To solve this problem, a visible watermarking scheme with
embedding and removing process is proposed under the control of a
secure template. The template generates different version of
watermarks which can be seen visually the same for different users.
Users with the right key can completely remove the watermark and
recover the original image while the unauthorized user is prevented to
remove the watermark. Experiment results show that our
watermarking algorithm obtains a good visual quality and is hard to be
removed by the illegally users. Additionally, the authorized users can
completely remove the visible watermark and recover the original
image with a good quality.
Abstract: A great deal of research works in the field information
systems security has been based on a positivist paradigm. Applying
the reductionism concept of the positivist paradigm for information
security means missing the bigger picture and thus, the lack of holism
which could be one of the reasons why security is still overlooked,
comes as an afterthought or perceived from a purely technical
dimension. We need to reshape our thinking and attitudes towards
security especially in a complex and dynamic environment such as e-
Business to develop a holistic understanding of e-Business security in
relation to its context as well as considering all the stakeholders in
the problem area. In this paper we argue the suitability and need for
more inductive interpretive approach and qualitative research method
to investigate e-Business security. Our discussion is based on a
holistic framework of enquiry, nature of the research problem, the
underling theoretical lens and the complexity of e-Business
environment. At the end we present a research strategy for
developing a holistic framework for understanding of e-Business
security problems in the context of developing countries based on an
interdisciplinary inquiry which considers their needs and
requirements.
Abstract: Automotive engine air-ratio plays an important role of
emissions and fuel consumption reduction while maintains
satisfactory engine power among all of the engine control variables. In
order to effectively control the air-ratio, this paper presents a model
predictive fuzzy control algorithm based on online least-squares
support vector machines prediction model and fuzzy logic optimizer.
The proposed control algorithm was also implemented on a real car for
testing and the results are highly satisfactory. Experimental results
show that the proposed control algorithm can regulate the engine
air-ratio to the stoichiometric value, 1.0, under external disturbance
with less than 5% tolerance.
Abstract: Public parks are placed high on the research agenda, with many studies addressing their social, economic and environment influences in different countries around the world. They have been recognized as contributors to the physical quality of urban environments. Recently, a broader view of public parks has emerged. This view goes well beyond the traditional value of parks as places for more recreation and visual delight, to depict them as valuable contributors to broader strategic objectives, such as property values, place attractiveness, job opportunities, social belonging, public health, tourist development, and improving the overall quality of life. This research examines the role of public parks in enhancing the quality of human life in Egyptian environment. It measures 'quality of life' in terms of 'human needs' and 'well-being'. This should open ways for policymakers, practitioners, researchers and the public to realize the potentials of public parks towards improving the quality of life.
Abstract: The study aims to develop a framework of social
network management to enhance customer relationship. Social
network management of this research is derived from social network
site management, individual and organization social network usage
motivation. The survey was conducted with organization employees
who have used social network to interact with customers. The results
reveal that content, link, privacy and security, page design and
interactivity are the major issues of social network site management.
Content, link, privacy and security, individual and organization
motivation have major impacts on encouraging business knowledge
sharing among employees. Moreover, Page design and interactivity,
content, organization motivation and knowledge sharing can improve
customer relationships.
Abstract: The estimation of overall on-site and off-site greenhouse gas (GHG) emissions by wastewater treatment plants revealed that in anaerobic and hybrid treatment systems greater emissions result from off-site processes compared to on-site processes. However, in aerobic treatment systems, onsite processes make a higher contribution to the overall GHG emissions. The total GHG emissions were estimated to be 1.6, 3.3 and 3.8 kg CO2-e/kg BOD in the aerobic, anaerobic and hybrid treatment systems, respectively. In the aerobic treatment system without the recovery and use of the generated biogas, the off-site GHG emissions were 0.65 kg CO2-e/kg BOD, accounting for 40.2% of the overall GHG emissions. This value changed to 2.3 and 2.6 kg CO2-e/kg BOD, and accounted for 69.9% and 68.1% of the overall GHG emissions in the anaerobic and hybrid treatment systems, respectively. The increased off-site GHG emissions in the anaerobic and hybrid treatment systems are mainly due to material usage and energy demand in these systems. The anaerobic digester can contribute up to 100%, 55% and 60% of the overall energy needs of plants in the aerobic, anaerobic and hybrid treatment systems, respectively.
Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.