Abstract: This paper deals with the status of solid waste pollution in touristic spots of North coastal Andhra Pradesh. Case studies of Eco tourism, cultural tourism and pilgrim tourism are elaborately discussed and the study is based on both primary and secondary data. Data collection includes field collection of solid waste, semi structured interviews and observation of tourists. Results indicate generation of 72% Non biodegradable material in Eco touristic places like RK beach Visakhapatnam, Araku Valley. Pydithalli Jathra is a famous cultural touristic attraction and more than one lakh people converge here. The solid waste at this spot includes 20% coconut shells, 50% plastic bottles and covers, 20% Banana peelings and remaining are food materials. Radhasapthami is the most important festival celebrated at famous sun temple Arasavalli of Srikakulam. Here solid waste includes 50% water bottles, plastic covers, 10% papers, 10% hair, 30% left out food material and Banana peelings.
Abstract: Interaction of inorganic water-soluble salts and building stones is studied in the paper. Two types of sandstone and one type of spongillite as representatives of materials used in historical masonry are subjected to experimental testing. Within the performed experiments, measurement of moisture and chloride concentration profiles is done in order to get input data for computational inverse analysis. Using the inverse analysis, moisture diffusivity and chloride diffusion coefficient of investigated materials are accessed. Additionally, the effect of salt presence on water vapor storage is investigated using dynamic vapor sorption device. The obtained data represents valuable information for restoration of historical masonry and give evidence on the performance of studied stones in contact with water soluble salts.
Abstract: This paper studied the synthesis of monoacylglycerol (monolaurin) by glycerolysis of coconut oil and crude glycerol, catalyzed by Carica papaya lipase. Coconut oil obtained from cold pressed extraction method and crude glycerol obtained from the biodiesel plant in Department of Chemistry, Uttaradit Rajabhat University, Thailand which used oils were used as raw materials for biodiesel production through transesterification process catalyzed by sodium hydroxide. The influences of the following variables were studied: (i) type of organic solvent, (ii) molar ratio of substrate, (iii) reaction temperature, (iv) reaction time, (v) lipase dosage, and (vi) initial water activity of enzyme. High yields in monoacylglycerol (58.35%) were obtained with molar ratio of glycerol to oil at 8:1 in ethanol, temperature was controlled at 45oC for 36 hours, the amount of enzyme used was 20 wt% of oil and initial water activity of enzyme at 0.53.
Abstract: Ultrasonic machining (USM) is a non-traditional
machining process being widely used for commercial machining of
brittle and fragile materials such as glass, ceramics and
semiconductor materials. However, USM could be a viable
alternative for machining a tough material such as titanium; and this
aspect needs to be explored through experimental research. This
investigation is focused on exploring the use of ultrasonic machining
for commercial machining of pure titanium (ASTM Grade-I) and
evaluation of tool wear rate (TWR) under controlled experimental
conditions. The optimal settings of parameters are determined
through experiments planned, conducted and analyzed using Taguchi
method. In all, the paper focuses on parametric optimization of
ultrasonic machining of pure titanium metal with TWR as response,
and validation of the optimized value of TWR by conducting
confirmatory experiments.
Abstract: The aim of the article is to describe modern
contemporary systems of employees' remuneration used in
organizations, to give a general overview of these questions based on
the questionnaire survey made by the authors, as well as to assess
possible effects of economic crisis in this area. It is necessary to be
aware of the fact that firm's success in the contemporary business
environment depends not only on the technical equipment, financial
resources, availability of raw materials and information and effective
management, but one of the crucial factors of firm's success is its
human potential. The article emphasizes that the well working
remuneration system has a very important position in the
organization in the broadest sense. The paper also aims to the current
situation in the area of employees' remuneration in one of Czech
Republic regions, in the Moravian-Silesian Region.
Abstract: Our results showed that for the growth of qualitative
seedling and vegetative raw material of ðó. marschallianus Willd. and
T. serphyllum L. it is more profitable to use the in vitro and
hydroponics combined method. In in vitro culture it is possible to do
micro-propagation whole year with 98-99% rhizogenesis. 30000
micro-plants were obtained from one explant during 9 months.
Hydroponic conditions provide the necessary microclimate for
microplants where the survival rate without acclimatization was
93.3%. The essential oil content in hydroponic dry herb of both
species in vegetative and blossom phase was 1.3% whereas in wild
plants it was 1.2%, the content of extractive substances and vitamin
C also exceeded wild plants. Our biochemical and radiochemical
investigations indicated that the medicinal raw materials obtained
from hydroponic and wild plants of Thymus species correspond to
the demands of SPh XI, and the content of artificial radionuclides
does not exceed the MACL.
Abstract: Semiconductor nanomaterials like TiO2 nanoparticles
(TiO2-NPs) approximately less than 100 nm in diameter have become
a new generation of advanced materials due to their novel and
interesting optical, dielectric, and photo-catalytic properties. With the
increasing use of NPs in commerce, to date few studies have
investigated the toxicological and environmental effects of NPs.
Motivated by the importance of TiO2-NPs that may contribute to the
cancer research field especially from the treatment prospective
together with the fractal analysis technique, we have investigated the
effect of TiO2-NPs on colony morphology in the dark condition
using fractal dimension as a key morphological characterization
parameter. The aim of this work is mainly to investigate the cytotoxic
effects of TiO2-NPs in the dark on the growth of human cervical
carcinoma (HeLa) cell colonies from morphological aspect. The in
vitro studies were carried out together with the image processing
technique and fractal analysis. It was found that, these colonies were
abnormal in shape and size. Moreover, the size of the control
colonies appeared to be larger than those of the treated group. The
mean Df +/- SEM of the colonies in untreated cultures was
1.085±0.019, N= 25, while that of the cultures treated with TiO2-NPs
was 1.287±0.045. It was found that the circularity of the control
group (0.401±0.071) is higher than that of the treated group
(0.103±0.042). The same tendency was found in the diameter
parameters which are 1161.30±219.56 μm and 852.28±206.50 μm
for the control and treated group respectively. Possible explanation of
the results was discussed, though more works need to be done in
terms of the for mechanism aspects. Finally, our results indicate that
fractal dimension can serve as a useful feature, by itself or in
conjunction with other shape features, in the classification of cancer
colonies.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: The main emphasis of metallurgists has been to process the materials to obtain the balanced mechanical properties for the given application. One of the processing routes to alter the properties is heat treatment. Nearly 90% of the structural applications are related to the medium carbon an alloyed steels and hence are regarded as structural steels. The major requirement in the conventional steel is to improve workability, toughness, hardness and grain refinement. In this view, it is proposed to study the mechanical and tribological properties of unalloyed structural (AISI 1140) steel with different thermal (heat) treatments like annealing, normalizing, tempering and hardening and compared with as brought (cold worked) specimen. All heat treatments are carried out in atmospheric condition. Hardening treatment improves hardness of the material, a marginal decrease in hardness value with improved ductility is observed in tempering. Annealing and normalizing improve ductility of the specimen. Normalized specimen shows ultimate ductility. Hardened specimen shows highest wear resistance in the initial period of slide wear where as above 25KM of sliding distance, as brought steel dominates the hardened specimen. Both mild and severe wear regions are observed. Microstructural analysis shows the existence of pearlitic structure in normalized specimen, lath martensitic structure in hardened, pearlitic, ferritic structure in annealed specimen.
Abstract: This article first summarizes reasons why current approaches supporting Open Learning and Distance Education need to be complemented by tools permitting lecturers, researchers and students to cooperatively organize the semantic content of Learning related materials (courses, discussions, etc.) into a fine-grained shared semantic network. This first part of the article also quickly describes the approach adopted to permit such a collaborative work. Then, examples of such semantic networks are presented. Finally, an evaluation of the approach by students is provided and analyzed.
Abstract: In this paper, a generalized self-consistent scheme, or “three phase model", is used to set up a micro-mechanics model for rough surface contact with randomly distributed asperities. The dimensionless average real pressure p is obtained as function of the ratio of the real contact area to the apparent contact area, 0 A / A r . Both elastic and plastic materials are considered, and the influence of the plasticity of material on p is discussed. Both two-dimensional and three-dimensional rough surface contact problems are considered.
Abstract: The feasibility of applying a simple and cost effective sliding friction testing apparatus to study the friction behaviour of a clutch facing material, effected by the variation of temperature and contact pressure, was investigated. It was found that the method used in this work was able to give a convenient and cost effective measurement of friction coefficients and their transitions of a clutch facing material. The obtained results will be useful for the development process of new facing materials.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: The stilling basins are commonly used to dissipate the
energy and protect the downstream floor from erosion. The aim of
the present experimental work is to improve the roughened stilling
basin using T-shape roughness instead of the regular cubic one and
design this new shape. As a result of the present work the best
intensity and the best roughness length are identified. Also, it is
found that the T-shape roughness save materials and reduce the jump
length compared to the cubic one. Sensitivity analysis was performed
and it was noticed that the change in the length of jump is more
sensitive to the change in roughness length than the change in
intensity.
Abstract: Based on 276 responses from academic staff in an
evaluation of an online learning environment (OLE), this paper
identifies those elements of the OLE that were most used and valued
by staff, those elements of the OLE that staff most wanted to see
improved, and those factors that most contributed to staff perceptions
that the use of the OLE enhanced their teaching. The most used and
valued elements were core functions, including accessing unit
information, accessing lecture/tutorial/lab notes, and reading online
discussions. The elements identified as most needing attention related
to online assessment: submitting assignments, managing assessment
items, and receiving feedback on assignments. Staff felt that using the
OLE enhanced their teaching when they were satisfied that their
students were able to access and use their learning materials, and
when they were satisfied with the professional development they
received and were confident with their ability to teach with the OLE.
Abstract: In the modern construction practices, industrial wastes
or by-products are largely used as raw materials in cement and
concrete. These impart many benefits to the environment and bringabout
an economic impact because the cost of waste disposal is
constantly increasing due to strict environmental regulations. It was
reported in literature that the leakage of oil onto concrete element in
older cement grinding unit resulted in concrete with greater resistance
to freezing and thawing. This effect was thought to be similar to
adding an air-entraining chemical admixture to concrete. This paper
presents an investigation on the load deflection behaviour and crack
patterns of reinforced concrete (RC) beams subjected to four point
loading. Ten 120x260x1900 mm beams were cast with 100%
ordinary Portland cement (OPC) concrete, 20% fly ash (FA) and 20%
rice husk ash (RHA) blended cement concrete. 0.15% dosage of
admixtures (used engine oil, new engine oil, and superplasticizer)
was used throughout the experiment. Results show that OPC and
OPC/RHA RC beams containing used engine oil and superplasticizer
exhibit higher capacity, 18-26% than their corresponding control
mix.
Abstract: In this paper, the bio-mechanical analysis of human joints is carried out and the study is extended to the robot manipulator. This study will first focus on the kinematics of human arm which include the movement of each joint in shoulder, wrist, elbow and finger complexes. Those analyses are then extended to the design of a human robot manipulator. A simulator is built for Direct Kinematics and Inverse Kinematics of human arm. In the simulation of Direct Kinematics, the human joint angles can be inserted, while the position and orientation of each finger tips (end-effector) are shown. Inverse Kinematics does the reverse of the Direct Kinematics. Based on previous materials obtained from kinematics analysis, the human manipulator joints can be designed to follow prescribed position trajectories.
Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: Human always tried to create a suitable situation for their life according to environmental conditions. In fact, geography has an important role in the shape of our living area. Iran also as a four-season country has different climate type: hot and humid, hot and dry, mid and humid, and cold; therefore, we can find different architecture styles in Iran. Gilan-s traditional architecture is a suitable sample of sustainable construction in Iran. Because the main factors of every dwelling are the climatic, social, economic and cultural effects which demonstrate the interaction between environment and people settlement. This paper was determined the interaction between environmental factors and the rural dwellings in the Gilan province. Also, traditional village (city) of Masouleh as a rare sample of rural and sustainable architecture was introduced.
Abstract: An investigation of the process of deformation hardening and evolution of deformation defect medium in dispersion-hardened materials with face centered cubic matrices and nanoparticles was done. Mathematical model including balance equation for the deformation defects was used.