Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: Texture classification is a trendy and a catchy
technology in the field of texture analysis. Textures, the repeated
patterns, have different frequency components along different
orientations. Our work is based on Texture Classification and its
applications. It finds its applications in various fields like Medical
Image Classification, Computer Vision, Remote Sensing,
Agricultural Field, and Textile Industry. Weed control has a major
effect on agriculture. A large amount of herbicide has been used for
controlling weeds in agriculture fields, lawns, golf courses, sport
fields, etc. Random spraying of herbicides does not meet the exact
requirement of the field. Certain areas in field have more weed
patches than estimated. So, we need a visual system that can
discriminate weeds from the field image which will reduce or even
eliminate the amount of herbicide used. This would allow farmers to
not use any herbicides or only apply them where they are needed. A
machine vision precision automated weed control system could
reduce the usage of chemicals in crop fields. In this paper, an
intelligent system for automatic weeding strategy Multi Resolution
Combined Statistical & spatial Frequency is used to discriminate the
weeds from the crops and to classify them as narrow, little and broad
weeds.
Abstract: It is expected that ubiquitous era will come soon. A ubiquitous environment has features like peer-to-peer and nomadic environments. Such features can be represented by peer-to-peer systems and mobile ad-hoc networks (MANETs). The features of P2P systems and MANETs are similar, appealing for implementing P2P systems in MANET environment. It has been shown that, however, the performance of the P2P systems designed for wired networks do not perform satisfactorily in mobile ad-hoc environment. Subsequently, this paper proposes a method to improve P2P performance using cross-layer design and the goodness of a node as a peer. The proposed method uses routing metric as well as P2P metric to choose favorable peers to connect. It also utilizes proactive approach for distributing peer information. According to the simulation results, the proposed method provides higher query success rate, shorter query response time and less energy consumption by constructing an efficient overlay network.
Abstract: All the geophysical phenomena including river
networks and flow time series are fractal events inherently and fractal
patterns can be investigated through their behaviors. A non-linear
system like a river basin can well be analyzed by a non-linear
measure such as the fractal analysis. A bilateral study is held on the
fractal properties of the river network and the river flow time series.
A moving window technique is utilized to scan the fractal properties
of them. Results depict both events follow the same strategy
regarding to the fractal properties. Both the river network and the
time series fractal dimension tend to saturate in a distinct value.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: This research aims at development of the Multiple
Intelligences Measurement of Elementary Students. The structural
accuracy test and normality establishment are based on the Multiple
Intelligences Theory of Gardner. This theory consists of eight aspects
namely linguistics, logic and mathematics, visual-spatial relations,
body and movement, music, human relations, self-realization/selfunderstanding
and nature. The sample used in this research consists
of elementary school students (aged between 5-11 years). The size of
the sample group was determined by Yamane Table. The group has
2,504 students. Multistage Sampling was used. Basic statistical
analysis and construct validity testing were done using confirmatory
factor analysis. The research can be summarized as follows; 1.
Multiple Intelligences Measurement consisting of 120 items is
content-accurate. Internal consistent reliability according to the
method of Kuder-Richardson of the whole Multiple Intelligences
Measurement equals .91. The difficulty of the measurement test is
between .39-.83. Discrimination is between .21-.85. 2). The Multiple
Intelligences Measurement has construct validity in a good range,
that is 8 components and all 120 test items have statistical
significance level at .01. Chi-square value equals 4357.7; p=.00 at the
degree of freedom of 244 and Goodness of Fit Index equals 1.00.
Adjusted Goodness of Fit Index equals .92. Comparative Fit Index
(CFI) equals .68. Root Mean Squared Residual (RMR) equals 0.064
and Root Mean Square Error of Approximation equals 0.82. 3). The
normality of the Multiple Intelligences Measurement is categorized
into 3 levels. Those with high intelligence are those with percentiles
of more than 78. Those with moderate/medium intelligence are those
with percentiles between 24 and 77.9. Those with low intelligence
are those with percentiles from 23.9 downwards.
Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: The objectives of this research paper were to study the
influencing factors that contributed to the success of electronic
commerce (e-commerce) and to study the approach to enhance the
standard of e-commerce for small and medium enterprises (SME).
The research paper focused the study on only sole proprietorship
SMEs in Bangkok, Thailand. The factors contributed to the success
of SME included business management, learning in the organization,
business collaboration, and the quality of website. A quantitative and
qualitative mixed research methodology was used. In terms of
quantitative method, a questionnaire was used to collect data from
251 sole proprietorships. The System Equation Model (SEM) was
utilized as the tool for data analysis. In terms of qualitative method,
an in-depth interview, a dialogue with experts in the field of ecommerce
for SMEs, and content analysis were used.
By using the adjusted causal relationship structure model, it was
revealed that the factors affecting the success of e-commerce for
SMEs were found to be congruent with the empirical data. The
hypothesis testing indicated that business management influenced the
learning in the organization, the learning in the organization
influenced business collaboration and the quality of the website, and
these factors, in turn, influenced the success of SMEs. Moreover, the
approach to enhance the standard of SMEs revealed that the majority
of respondents wanted to enhance the standard of SMEs to a high
level in the category of safety of e-commerce system, basic structure
of e-commerce, development of staff potentials, assistance of budget
and tax reduction, and law improvement regarding the e-commerce
respectively.
Abstract: Three sulphonic acid-doped polyanilines were
synthesized through chemical oxidation at low temperature (0-5 oC)
and potential of these polymers as sensing agent for O2 gas detection
in terms of fluorescence quenching was studied. Sulphuric acid,
dodecylbenzene sulphonic acid (DBSA) and camphor sulphonic acid
(CSA) were used as doping agents. All polymers obtained were dark
green powder. Polymers obtained were characterized by Fourier
transform infrared spectroscopy, ultraviolet-visible absorption
spectroscopy, thermogravimetry analysis, elemental analysis,
differential scanning calorimeter and gel permeation
chromatography. Characterizations carried out showed that polymers
were successfully synthesized with mass recovery for sulphuric aciddoped
polyaniline (SPAN), DBSA-doped polyaniline (DBSA-doped
PANI) and CSA-doped polyaniline (CSA-doped PANI) of 71.40%,
75.00% and 39.96%, respectively. Doping level of SPAN, DBSAdoped
PANI and CSA-doped PANI were 32.86%, 33.13% and
53.96%, respectively as determined based on elemental analysis.
Sensing test was carried out on polymer sample in the form of
solution and film by using fluorescence spectrophotometer. Samples
of polymer solution and polymer film showed positive response
towards O2 exposure. All polymer solutions and films were fully
regenerated by using N2 gas within 1 hour period. Photostability
study showed that all samples of polymer solutions and films were
stable towards light when continuously exposed to xenon lamp for 9
hours. The relative standard deviation (RSD) values for SPAN
solution, DBSA-doped PANI solution and CSA-doped PANI
solution for repeatability were 0.23%, 0.64% and 0.76%,
respectively. Meanwhile RSD values for reproducibility were 2.36%,
6.98% and 1.27%, respectively. Results for SPAN film, DBSAdoped
PANI film and CSA-doped PANI film showed the same
pattern with RSD values for repeatability of 0.52%, 4.05% and
0.90%, respectively. Meanwhile RSD values for reproducibility were
2.91%, 10.05% and 7.42%, respectively. The study on effect of the
flow rate on response time was carried out using 3 different rates
which were 0.25 mL/s, 1.00 mL/s and 2.00 mL/s. Results obtained
showed that the higher the flow rate, the shorter the response time.
Abstract: Since the feasibility study of R&D programs have been
initiated for efficient public R&D investments, year 2008, feasibility
studies have improved in terms of precision. Although experience
related to these studies of R&D programs have increased to a certain
point, still methodological improvement is required. The feasibility
studies of R&D programs are consisted of various viewpoints, such as
technology, policy, and economics. This research is to provide
improvement methods to the economic perspective; especially the cost
estimation process of R&D activities. First of all, the fundamental
concept of cost estimation is reviewed. After the review, a statistical
and econometric analysis method is applied as empirical analysis.
Conclusively, limitations and further research directions are provided.
Abstract: In a complex project environment, project teams face
multi-dimensional communication problems that can ultimately lead
to project breakdown. Team Performance varies in Face-to-Face
(FTF) environment versus groups working remotely in a computermediated
communication (CMC) environment. A brief review of the
Input_Process_Output model suggested by James E. Driskell, Paul H.
Radtke and Eduardo Salas in “Virtual Teams: Effects of
Technological Mediation on Team Performance (2003)", has been
done to develop the basis of this research. This model theoretically
analyzes the effects of technological mediation on team processes,
such as, cohesiveness, status and authority relations, counternormative
behavior and communication. An empirical study
described in this paper has been undertaken to test the
“cohesiveness" of diverse project teams in a multi-national
organization. This study uses both quantitative and qualitative
techniques for data gathering and analysis. These techniques include
interviews, questionnaires for data collection and graphical data
representation for analyzing the collected data. Computer-mediated
technology may impact team performance because of difference in
cohesiveness among teams and this difference may be moderated by
factors, such as, the type of communication environment, the type of
task and the temporal context of the team. Based on the reviewed
model, sets of hypotheses are devised and tested. This research,
reports on a study that compared team cohesiveness among virtual
teams using CMC and non-CMC communication mediums. The
findings suggest that CMC can help virtual teams increase team
cohesiveness among their members, making CMC an effective
medium for increasing productivity and team performance.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: Segmentation is an important step in medical image
analysis and classification for radiological evaluation or computer
aided diagnosis. This paper presents the problem of inaccurate lung
segmentation as observed in algorithms presented by researchers
working in the area of medical image analysis. The different lung
segmentation techniques have been tested using the dataset of 19
patients consisting of a total of 917 images. We obtained datasets of
11 patients from Ackron University, USA and of 8 patients from
AGA Khan Medical University, Pakistan. After testing the algorithms
against datasets, the deficiencies of each algorithm have been
highlighted.
Abstract: Lanthanide-doped upconversion nanoparticles which can convert near-infrared lights to visible lights have attracted growing interest because of their great potentials in fluorescence imaging. Upconversion fluorescence imaging technique with excitation in the near-infrared (NIR) region has been used for imaging of biological cells and tissues. However, improving the detection sensitivity and decreasing the absorption and scattering in biological tissues are as yet unresolved problems. In this present study, a novel NIR-reflected multispectral imaging system was developed for upconversion fluorescent imaging in small animals. Based on this system, we have obtained the high contrast images without the autofluorescence when biocompatible UCPs were injected near the body surface or deeply into the tissue. Furthermore, we have extracted respective spectra of the upconversion fluorescence and relatively quantify the fluorescence intensity with the multispectral analysis. To our knowledge, this is the first time to analyze and quantify the upconversion fluorescence in the small animal imaging.
Abstract: Electromyography (EMG) is the study of muscles function through analysis of electrical activity produced from muscles. This electrical activity which is displayed in the form of signal is the result of neuromuscular activation associated with muscle contraction. The most common techniques of EMG signal recording are by using surface and needle/wire electrode where the latter is usually used for interest in deep muscle. This paper will focus on surface electromyogram (SEMG) signal. During SEMG recording, several problems had to been countered such as noise, motion artifact and signal instability. Thus, various signal processing techniques had been implemented to produce a reliable signal for analysis. SEMG signal finds broad application particularly in biomedical field. It had been analyzed and studied for various interests such as neuromuscular disease, enhancement of muscular function and human-computer interface.
Abstract: This paper discusses the novel graphical approach for
stability analysis of multi induction motor drive controlled by a single
inverter. Stability issue arises in parallel connected induction motors
under unbalanced load conditions. The two powerful globally
accepted modeling and simulation software packages such as
MATLAB and LabVIEW are selected to perform the stability
analysis. The stability investigation is performed for different load
conditions and difference in stator and rotor resistances among the
two motors. It is very simple and effective than the techniques
presented to obtain the stability of the parallel connected induction
motor drive under unbalanced load conditions. Approximate transfer
functions are considered to model the induction motors, load
dynamics, speed controllers and inverter. Simulink library tools are
utilized to model the entire drive scheme in MATLAB. Stability
study is discussed in LabVIEW using control design and simulation
toolkits. Simulation results are illustrated for various running
conditions to demonstrate the effectiveness of the transfer function
method.
Abstract: This study has investigated the antidiabetic and
antioxidant potential of Pseudovaria macrophylla bark extract on
streptozotocin–nicotinamide induced type 2 diabetic rats. LCMSQTOF
and NMR experiments were done to determine the chemical
composition in the methanolic bark extract. For in vivo experiments,
the STZ (60 mg/kg/b.w, 15 min after 120 mg/kg/1 nicotinamide, i.p.)
induced diabetic rats were treated with methanolic extract of
Pseuduvaria macrophylla (200 and 400 mg/kg·bw) and
glibenclamide (2.5 mg/kg) as positive control respectively.
Biochemical parameters were assayed in the blood samples of all
groups of rats. The pro-inflammatory cytokines, antioxidant status
and plasma transforming growth factor βeta-1 (TGF-β1) were
evaluated. The histological study of the pancreas was examined and
its expression level of insulin was observed by
immunohistochemistry. In addition, the expression of glucose
transporters (GLUT 1, 2 and 4) were assessed in pancreas tissue by
western blot analysis. The outcomes of the study displayed that the
bark methanol extract of Pseuduvaria macrophylla has potentially
normalized the elevated blood glucose levels and improved serum
insulin and C-peptide levels with significant increase in the
antioxidant enzyme, reduced glutathione (GSH) and decrease in the
level of lipid peroxidation (LPO). Additionally, the extract has
markedly decreased the levels of serum pro-inflammatory cytokines
and transforming growth factor beta-1 (TGF-β1). Histopathology
analysis demonstrated that Pseuduvaria macrophylla has the
potential to protect the pancreas of diabetic rats against peroxidation
damage by downregulating oxidative stress and elevated
hyperglycaemia. Furthermore, the expression of insulin protein,
GLUT-1, GLUT-2 and GLUT-4 in pancreatic cells was enhanced.
The findings of this study support the anti-diabetic claims of
Pseudovaria macrophylla bark.
Abstract: Cosmic showers, during the transit through space, produce
sub - products as a result of interactions with the intergalactic
or interstellar medium which after entering earth generate secondary
particles called Extensive Air Shower (EAS). Detection and analysis
of High Energy Particle Showers involve a plethora of theoretical and
experimental works with a host of constraints resulting in inaccuracies
in measurements. Therefore, there exist a necessity to develop a
readily available system based on soft-computational approaches
which can be used for EAS analysis. This is due to the fact that soft
computational tools such as Artificial Neural Network (ANN)s can be
trained as classifiers to adapt and learn the surrounding variations. But
single classifiers fail to reach optimality of decision making in many
situations for which Multiple Classifier System (MCS) are preferred
to enhance the ability of the system to make decisions adjusting
to finer variations. This work describes the formation of an MCS
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN) with data inputs
from correlation mapping Self Organizing Map (SOM) blocks and
the output optimized by another SOM. The results show that the setup
can be adopted for real time practical applications for prediction
of primary energy and location of EAS from density values captured
using detectors in a circular grid.
Abstract: The proposed multiplexer-based novel 1-bit full
adder cell is schematized by using DSCH2 and its layout is generated
by using microwind VLSI CAD tool. The adder cell layout
interconnect analysis is performed by using BSIM4 layout analyzer.
The adder circuit is compared with other six existing adder circuits
for parametric analysis. The proposed adder cell gives better
performance than the other existing six adder circuits in terms of
power, propagation delay and PDP. The proposed adder circuit is
further analyzed for interconnect analysis, which gives better
performance than other adder circuits in terms of layout thickness,
width and height.