Abstract: This paper reviews the optimization available
transmission capability (ATC) of power systems using a device of
FACTS named SSSC equipped with energy storage devices. So that,
emplacement and improvement of parameters of SSSC will be
illustrated. Thus, voltage magnitude constraints of network buses,
line transient stability constraints and voltage breakdown constraints
are considered. To help the calculations, a comprehensive program in
DELPHI is provided, which is able to simulate and trace the
parameters of SSSC has been installed on a specific line.
Furthermore, the provided program is able to compute ATC, TTC
and maximum value of their enhancement after using SSSC.
Abstract: We developed a GPS-based navigation device for the
blind, with audio guidance in Thai language. The device is composed
of simple and inexpensive hardware components. Its user interface is
quite simple. It determines optimal routes to various landmarks in our
university campus by using heuristic search for the next waypoints.
We tested the device and made note of its limitations and possible
extensions.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: Multi-level voltage source inverters offer several
advantages such as; derivation of a refined output voltage with
reduced total harmonic distortion (THD), reduction of voltage ratings
of the power semiconductor switching devices and also the reduced
electro-magnetic-interference problems etc. In this paper, new
carrier-overlapped phase-disposition or sub-harmonic sinusoidal
pulse width modulation (CO-PD-SPWM) and also the carrieroverlapped
phase-disposition space vector modulation (CO-PDSVPWM)
schemes for a six-level diode-clamped inverter topology
are proposed. The principle of the proposed PWM schemes is similar
to the conventional PD-PWM with a little deviation from it in the
sense that the triangular carriers are all overlapped. The overlapping
of the triangular carriers on one hand results in an increased number
of switchings, on the other hand this facilitates an improved spectral
performance of the output voltage. It is demonstrated through
simulation studies that the six-level diode-clamped inverter with the
use of CO-PD-SPWM and CO-PD-SVPWM proposed in this paper is
capable of generating multiple levels in its output voltage. The
advantages of the proposed PWM schemes can be derived to benefit,
especially at lower modulation indices of the inverter and hence this
aspect of the proposed PWM schemes can be well exploited in high
power applications requiring low speeds of operation of the drive.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: Fuel cell's system requires regulating circuit for
voltage and current in order to control power in case of connecting to
other generative devices or load. In this paper Fuel cell system and
convertor, which is a multi-variable system, are controlled using
sliding mode method. Use of weighting matrix in design procedure
made it possible to regulate speed of control. Simulation results show
the robustness and accuracy of proposed controller for controlling
desired of outputs.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: This paper presents a web based remote access
microcontroller laboratory. Because of accelerated development in
electronics and computer technologies, microcontroller-based devices
and appliances are found in all aspects of our daily life. Before the
implementation of remote access microcontroller laboratory an
experiment set is developed by teaching staff for training
microcontrollers. Requirement of technical teaching and industrial
applications are considered when experiment set is designed.
Students can make the experiments by connecting to the experiment
set which is connected to the computer that set as the web server. The
students can program the microcontroller, can control digital and
analog inputs and can observe experiment. Laboratory experiment
web page can be accessed via www.elab.aku.edu.tr address.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: A generalized method for small-signal simulation of
avalanche noise in Mixed Tunneling Avalanche Transit Time
(MITATT) device is presented in this paper where the effect of series
resistance is taken into account. The method is applied to a
millimeter-wave Double Drift Region (DDR) MITATT device based
on Silicon to obtain noise spectral density and noise measure as a
function of frequency for different values of series resistance. It is
found that noise measure of the device at the operating frequency
(122 GHz) with input power density of 1010 Watt/m2 is about 35 dB
for hypothetical parasitic series resistance of zero ohm (estimated
junction temperature = 500 K). Results show that the noise measure
increases as the value of parasitic resistance increases.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: This paper presents the control performance of a high-precision positioning device using the hybrid actuator composed of a piezoelectric (PZT) actuator and a voice-coil motor (VCM). The combined piezo-VCM actuator features two main characteristics: a large operation range due to long stroke of the VCM, and high precision and heavy load positioning ability due to PZT impact force. A one-degree-of-freedom (DOF) experimental setup was configured to examine the fundamental characteristics, and the control performance was effectively demonstrated by using a switching controller. In rough positioning state, an integral variable structure controller (IVSC) was used for the VCM to conduct long range of operation; in precision positioning state, an impact force controller (IFC) for the PZT actuator coupled with presliding states of the sliding table was used to obtain high-precision position control and achieve both forward and backward actuations. The experimental results showed that the sliding table having a mass of 881g and with a preload of 10 N was successfully positioned within the positioning accuracy of 10 nm in both forward and backward position controls.
Abstract: This work presents an approach for the measurement
of mutual inductance on near field inductive coupling. The mutual
inductance between inductive circuits allows the simulation of energy
transfer from reader to tag, that can be used in RFID and powerless
implantable devices. It also allows one to predict the maximum
voltage in the tag of the radio-frequency system.
Abstract: Since communications between tag and reader in RFID
system are by radio, anyone can access the tag and obtain its any
information. And a tag always replies with the same ID so that it is
hard to distinguish between a real and a fake tag. Thus, there are many
security problems in today-s RFID System. Firstly, unauthorized
reader can easily read the ID information of any Tag. Secondly,
Adversary can easily cheat the legitimate reader using the collected
Tag ID information, such as the any legitimate Tag. These security
problems can be typically solved by encryption of messages
transmitted between Tag and Reader and by authentication for Tag.
In this paper, to solve these security problems on RFID system, we
propose the Tag Authentication Scheme based on self shrinking
generator (SSG). SSG Algorithm using in our scheme is proposed by
W.Meier and O.Staffelbach in EUROCRYPT-94. This Algorithm is
organized that only one LFSR and selection logic in order to generate
random stream. Thus it is optimized to implement the hardware logic
on devices with extremely limited resource, and the output generating
from SSG at each time do role as random stream so that it is allow our
to design the light-weight authentication scheme with security against
some network attacks. Therefore, we propose the novel tag
authentication scheme which use SSG to encrypt the Tag-ID
transmitted from tag to reader and achieve authentication of tag.
Abstract: This paper describes the experimental efficiency of a
compact organic Rankine cycle (ORC) system with a compact
rotary-vane-type expander. The compact ORC system can be used for
power generation from low-temperature heat sources such as waste
heat from various small-scale heat engines, fuel cells, electric devices,
and solar thermal energy. The purpose of this study is to develop an
ORC system with a low power output of less than 1 kW with a hot
temperature source ranging from 60°C to 100°C and a cold
temperature source ranging from 10°C to 30°C. The power output of
the system is rather less due to limited heat efficiency. Therefore, the
system should have an economically optimal efficiency. In order to
realize such a system, an efficient and low-cost expander is
indispensable. An experimental ORC system was developed using the
rotary-vane-type expander which is one of possible candidates of the
expander. The experimental results revealed the expander
performance for various rotation speeds, expander efficiencies, and
thermal efficiencies. Approximately 30 W of expander power output
with 48% expander efficiency and 4% thermal efficiency with a
temperature difference between the hot and cold sources of 80°C was
achieved.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: We focus on the excitation and propagation properties
of surface plasmon polariton (SPP). We have developed a SPP
excitation device in combination with a grating structures fabricated
by using the scanning probe lithography. Perturbation approach was
used to investigate the coupling properties of SPP with a spatial
harmonic wave supported by a metallic grating. A phase shift grating
SPP coupler has been fabricated and the optical property was
evaluated by the Fraunhofer diffraction formula. We have been
experimentally confirmed the induced stop band by diffraction
measurement. We have also observed the wavenumber shift of the
resonance condition of SPP owing to effect of a phase shift.