Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: The resistive-inductive-capacitive behavior of long
interconnects which are driven by CMOS gates are presented in this
paper. The analysis is based on the ¤Ç-model of a RLC load and is
developed for submicron devices. Accurate and analytical
expressions for the output load voltage, the propagation delay and the
short circuit power dissipation have been proposed after solving a
system of differential equations which accurately describe the
behavior of the circuit. The effect of coupling capacitance between
input and output and the short circuit current on these performance
parameters are also incorporated in the proposed model. The
estimated proposed delay and short circuit power dissipation are in
very good agreement with the SPICE simulation with average
relative error less than 6%.
Abstract: This research presented in this paper is an on-going
project of an application of neural network and fuzzy models to
evaluate the sociological factors which affect the educational
performance of the students in Sri Lanka. One of its major goals is to
prepare the grounds to device a counseling tool which helps these
students for a better performance at their examinations, especially at
their G.C.E O/L (General Certificate of Education-Ordinary Level)
examination. Closely related sociological factors are collected as raw
data and the noise of these data are filtered through the fuzzy
interface and the supervised neural network is being utilized to
recognize the performance patterns against the chosen social factors.
Abstract: This paper presents Genetic Algorithm (GA) based
approach for the allocation of FACTS (Flexible AC Transmission
System) devices for the improvement of Power transfer capacity in an
interconnected Power System. The GA based approach is applied on
IEEE 30 BUS System. The system is reactively loaded starting from
base to 200% of base load. FACTS devices are installed in the
different locations of the power system and system performance is
noticed with and without FACTS devices. First, the locations, where
the FACTS devices to be placed is determined by calculating active
and reactive power flows in the lines. Genetic Algorithm is then
applied to find the amount of magnitudes of the FACTS devices. This
approach of GA based placement of FACTS devices is tremendous
beneficial both in terms of performance and economy is clearly
observed from the result obtained.
Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: In this paper, we present C@sa, a multiagent system aiming at modeling, controlling and simulating the behavior of an intelligent house. The developed system aims at providing to architects, designers and psychologists a simulation and control tool for understanding which is the impact of embedded and pervasive technology on people daily life. In this vision, the house is seen as an environment made up of independent and distributed devices, controlled by agents, interacting to support user's goals and tasks.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: The broadcast problem including the plan design is
considered. The data are inserted and numbered at predefined order
into customized size relations. The server ability to create a full,
regular Broadcast Plan (RBP) with single and multiple channels after
some data transformations is examined. The Regular Geometric
Algorithm (RGA) prepares a RBP and enables the users to catch their
items avoiding energy waste of their devices. Moreover, the
Grouping Dimensioning Algorithm (GDA) based on integrated
relations can guarantee the discrimination of services with a
minimum number of channels. This last property among the selfmonitoring,
self-organizing, can be offered by servers today
providing also channel availability and less energy consumption by
using smaller number of channels. Simulation results are provided.
Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The dynamic behaviour of a four-bar linkage driven by a velocity controlled DC motor is discussed in the paper. In particular the author presents the results obtained by means of a specifically developed software, which implements the mathematical models of all components of the system (linkage, transmission, electric motor, control devices). The use of this software enables a more efficient design approach, since it allows the designer to check, in a simple and immediate way, the dynamic behaviour of the mechanism, arising from different values of the system parameters.
Abstract: Multimedia information availability has increased
dramatically with the advent of video broadcasting on handheld
devices. But with this availability comes problems of maintaining the
security of information that is displayed in public. ISMA Encryption
and Authentication (ISMACryp) is one of the chosen technologies for
service protection in DVB-H (Digital Video Broadcasting-
Handheld), the TV system for portable handheld devices. The
ISMACryp is encoded with H.264/AVC (advanced video coding),
while leaving all structural data as it is. Two modes of ISMACryp are
available; the CTR mode (Counter type) and CBC mode (Cipher
Block Chaining) mode. Both modes of ISMACryp are based on 128-
bit AES algorithm. AES algorithms are more complex and require
larger time for execution which is not suitable for real time
application like live TV. The proposed system aims to gain a deep
understanding of video data security on multimedia technologies and
to provide security for real time video applications using selective
encryption for H.264/AVC. Five level of security proposed in this
paper based on the content of NAL unit in Baseline Constrain profile
of H.264/AVC. The selective encryption in different levels provides
encryption of intra-prediction mode, residue data, inter-prediction
mode or motion vectors only. Experimental results shown in this
paper described that fifth level which is ISMACryp provide higher
level of security with more encryption time and the one level provide
lower level of security by encrypting only motion vectors with lower
execution time without compromise on compression and quality of
visual content. This encryption scheme with compression process
with low cost, and keeps the file format unchanged with some direct
operations supported. Simulation was being carried out in Matlab.
Abstract: In this study, the Taguchi method was used to optimize the effect of HALO structure or halo implant variations on threshold voltage (VTH) and leakage current (ILeak) in 45nm p-type Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) device. Besides halo implant dose, the other process parameters which used were Source/Drain (S/D) implant dose, oxide growth temperature and silicide anneal temperature. This work was done using TCAD simulator, consisting of a process simulator, ATHENA and device simulator, ATLAS. These two simulators were combined with Taguchi method to aid in design and optimize the process parameters. In this research, the most effective process parameters with respect to VTH and ILeak are halo implant dose (40%) and S/D implant dose (52%) respectively. Whereas the second ranking factor affecting VTH and ILeak are oxide growth temperature (32%) and halo implant dose (34%) respectively. The results show that after optimizations approaches is -0.157V at ILeak=0.195mA/μm.
Abstract: High precision in motion is required to manipulate the
micro objects in precision industries for micro assembly, cell
manipulation etc. Precision manipulation is achieved based on the
appropriate mechanism design of micro devices such as
microgrippers. Design of a compliant based mechanism is the better
option to achieve a highly precised and controlled motion. This
research article highlights the method of designing a compliant based
three fingered microgripper suitable for holding asymmetric objects.
Topological optimization technique, a systematic method is
implemented in this research work to arrive a topologically optimized
design of the mechanism needed to perform the required micro
motion of the gripper. Optimization technique has a drawback of
generating senseless regions such as node to node connectivity and
staircase effect at the boundaries. Hence, it is required to have post
processing of the design to make it manufacturable. To reduce the
effect of post processing stage and to preserve the edges of the image,
a cubic spline interpolation technique is introduced in the MATLAB
program. Structural performance of the topologically developed
mechanism design is tested using finite element method (FEM)
software. Further the microgripper structure is examined to find its
fatigue life and vibration characteristics.
Abstract: Network Management Systems have played a great important role in information systems. Management is very important and essential in any fields. There are many managements such as configuration management, fault management, performance management, security management, accounting management and etc. Among them, configuration, fault and security management is more important than others. Because these are essential and useful in any fields. Configuration management is to monitor and maintain the whole system or LAN. Fault management is to detect and troubleshoot the system. Security management is to control the whole system. This paper intends to increase the network management functionalities including configuration management, fault management and security management. In configuration management system, this paper specially can support the USB ports and devices to detect and read devices configuration and solve to detect hardware port and software ports. In security management system, this paper can provide the security feature for the user account setting and user management and proxy server feature. And all of the history of the security such as user account and proxy server history are kept in the java standard serializable file. So the user can view the history of the security and proxy server anytime. If the user uses this system, the user can ping the clients from the network and the user can view the result of the message in fault management system. And this system also provides to check the network card and can show the NIC card setting. This system is used RMI (Remote Method Invocation) and JNI (Java Native Interface) technology. This paper is to implement the client/server network management system using Java 2 Standard Edition (J2SE). This system can provide more than 10 clients. And then this paper intends to show data or message structure of client/server and how to work using TCP/IP protocol.
Abstract: Dedicated Short Range Communication (DSRC) is a
key enabling technology for the next generation of
communication-based safety applications. One of the important
problems for DSRC deployment is maintaining high performance
under heavy channel load. Many studies focus on congestion control
mechanisms for simulating hundreds of physical radios deployed on
vehicles. The U.S. department of transportation-s (DOT) Intelligent
Transportation Systems (ITS) division has a plan to chosen prototype
on-board devices capable of transmitting basic “Here I am" safety
messages to other vehicles. The devices will be used in an IntelliDrive
safety pilot deployment of up to 3,000 vehicles. It is hard to log the
information of 3,000 vehicles. In this paper we present the designs and
issues related to the DSRC Radio Testbed under heavy channel load.
The details not only include the architecture of DSRC Radio Testbed,
but also describe how the Radio Interfere System is used to help for
emulating the congestion radio environment.
Abstract: Development of motor car safety devices has reduced
fatality rates in car accidents. Yet despite this increase in car safety,
neck injuries resulting from rear impact collisions, particularly at low
speed, remain a primary concern. In this study, FEA(Finite Element
Analysis) of seat was performed to evaluate neck injuries in rear
impact. And the FEA result was verified by comparison with the actual
test results. The dummy used in FE model and actual test is BioRID II
which is regarded suitable for rear impact collision analysis. A
threshold of the BioRID II neck injury indicators was also proposed to
upgrade seat performance in order to reduce whiplash injury. To
optimize the seat for a low-speed rear impact collision, a method was
proposed, which is multi-objective optimization idea using DOE
(Design of Experiments) results.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.