Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: A device analysis of the photoconductive
semiconductor switch is carried out to investigate distribution of
electric field and carrier concentrations as well as the current density
distribution. The operation of this device was then investigated as a
switch operating in X band. It is shown that despite the presence of
symmetry geometry, switch current density of the on-state steady
state mode is distributed asymmetrically throughout the device.
Abstract: Rotational Smart Lighting Control System can supply
the quantity of lighting which is required to run plants by rotating few
LED and Fluorescent instead of that are used in the existing plant
factories.The initial installation of the existing plants factory is
expensive, so in order to solve the problem with smart lighting control
system was developed.
The beam required intensity for the growth of crops, Photosynthetic
Photon Flux Density(PPFD)is calculated; and the number of LED, are
installed on the blades, set; using the Lighting Simulation
Program.Relux, it is able to confirm that the difference of the beam
intensity between the center and the outer of lighting system when the
lighting device is rotating.
Abstract: In this paper, for the first time, a two-dimensional
(2D) analytical drain current model for sub-100 nm multi-layered
gate material engineered trapezoidal recessed channel (MLGMETRC)
MOSFET: a novel design is presented and investigated using
ATLAS and DEVEDIT device simulators, to mitigate the large gate
leakages and increased standby power consumption that arise due to
continued scaling of SiO2-based gate dielectrics. The twodimensional
(2D) analytical model based on solution of Poisson-s
equation in cylindrical coordinates, utilizing the cylindrical
approximation, has been developed which evaluate the surface
potential, electric field, drain current, switching metric: ION/IOFF
ratio and transconductance for the proposed design. A good
agreement between the model predictions and device simulation
results is obtained, verifying the accuracy of the proposed analytical
model.
Abstract: In inspection and workpiece localization, sampling point data is an important issue. Since the devices for sampling only sample discrete points, not the completely surface, sampling size and location of the points will be taken into consideration. In this paper a method is presented for determining the sampled points size and location for achieving efficient sampling. Firstly, uncertainty analysis of the localization parameters is investigated. A localization uncertainty model is developed to predict the uncertainty of the localization process. Using this model the minimum size of the sampled points is predicted. Secondly, based on the algebra theory an eigenvalue-optimal optimization is proposed. Then a freeform surface is used in the simulation. The proposed optimization is implemented. The simulation result shows its effectivity.
Abstract: Sensors have been used in various kinds of academic
fields and applications. In this article, we propose the idea of
modularized sensors that combine multiple sensor modules into a
unique sensor. We divide a sensor into several units according to
functionalities. Each unit has different sensor modules, which share
the same type of connectors and can be serially and arbitrarily
connected each other. A user can combine different sensor modules
into a sensor platform according to requirements. Compared with
current modularized sensors, the proposed sensor platform is highly
flexible and reusable. We have implemented the prototype of the
proposed sensor platform, and the experimental results show the
proposed platform can work correctly.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: The following paper shows an interactive tool which
main purpose is to teach how to play a flute. It consists of three
stages the first one is the instruction and teaching process through a
software application, the second is the practice part when the user
starts to play the flute (hardware specially designed for this
application) this flute is capable of capturing how is being played the
flute and the final stage is the one in which the data captured are sent
to the software and the user is evaluated in order to give him / she a
correction or an acceptance
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: This paper presents a VLSI design approach of a highspeed
and real-time 2-D Discrete Wavelet Transform computing. The
proposed architecture, based on new and fast convolution approach,
reduces the hardware complexity in addition to reduce the critical
path to the multiplier delay. Furthermore, an advanced twodimensional
(2-D) discrete wavelet transform (DWT)
implementation, with an efficient memory area, is designed to
produce one output in every clock cycle. As a result, a very highspeed
is attained. The system is verified, using JPEG2000
coefficients filters, on Xilinx Virtex-II Field Programmable Gate
Array (FPGA) device without accessing any external memory. The
resulting computing rate is up to 270 M samples/s and the (9,7) 2-D
wavelet filter uses only 18 kb of memory (16 kb of first-in-first-out
memory) with 256×256 image size. In this way, the developed design
requests reduced memory and provide very high-speed processing as
well as high PSNR quality.
Abstract: Photonic Crystal (PhC) based devices are being
increasingly used in multifunctional, compact devices in integrated
optical communication systems. They provide excellent
controllability of light, yet maintaining the small size required for
miniaturization. In this paper, the band gap properties of PhCs and
their typical applications in optical waveguiding are considered.
Novel PhC based applications such as nonlinear switching and
tapers are considered and simulation results are shown using the
accurate time-domain numerical method based on Finite Difference
Time Domain (FDTD) scheme. The suitability of these devices for
novel applications is discussed and evaluated.
Abstract: There is need to explore emerging technologies based on carbon nanotube electronics as the MOS technology is approaching its limits. As MOS devices scale to the nano ranges, increased short channel effects and process variations considerably effect device and circuit designs. As a promising new transistor, the Carbon Nanotube Field Effect Transistor(CNTFET) avoids most of the fundamental limitations of the Traditional MOSFET devices. In this paper we present the analysis and comparision of a Carbon Nanotube FET(CNTFET) based 10(A current mirror with MOSFET for 32nm technology node. The comparision shows the superiority of the former in terms of 97% increase in output resistance,24% decrease in power dissipation and 40% decrease in minimum voltage required for constant saturation current. Furthermore the effect on performance of current mirror due to change in chirality vector of CNT has also been investigated. The circuit simulations are carried out using HSPICE model.
Abstract: Multicast Network Technology has pervaded our
lives-a few examples of the Networking Techniques and also for the
improvement of various routing devices we use. As we know the
Multicast Data is a technology offers many applications to the user
such as high speed voice, high speed data services, which is presently
dominated by the Normal networking and the cable system and
digital subscriber line (DSL) technologies. Advantages of Multi cast
Broadcast such as over other routing techniques. Usually QoS
(Quality of Service) Guarantees are required in most of Multicast
applications. The bandwidth-delay constrained optimization and we
use a multi objective model and routing approach based on genetic
algorithm that optimizes multiple QoS parameters simultaneously.
The proposed approach is non-dominated routes and the performance
with high efficiency of GA. Its betterment and high optimization has
been verified. We have also introduced and correlate the result of
multicast GA with the Broadband wireless to minimize the delay in
the path.
Abstract: Electrophoretic motion of a liquid droplet within an
uncharged cylindrical pore is investigated theoretically in this study. It
is found that the boundary effect in terms of the reduction of droplet
mobility (droplet velocity per unit strength of the applied electric field)
is very significant when the double layer surrounding the droplet is
thick, and diminishes as it gets very thin. Moreover, the viscosity ratio
of the ambient fluid to the internal one, σ, is a crucial factor in
determining its electrophoretic behavior. The boundary effect is less
significant as the viscosity ratio gets high. Up to 70% mobility
reduction is observed when this ratio is low (σ = 0.01), whereas only
40% reduction when it is high (σ = 100). The results of this study can
be utilized in various fields of biotechnology, such as a biosensor or a
lab-on-a-chip device.
Abstract: Current trends in manufacturing are characterized by
production broadening, innovation cycle shortening, and the products
having a new shape, material and functions. The production strategy
focused on time needed change from the traditional functional
production structure to flexible manufacturing cells and lines.
Production by automated manufacturing system (AMS) is one of the
most important manufacturing philosophies in the last years. The
main goals of the project we are involved in lies on building a
laboratory in which will be located a flexible manufacturing system
consisting of at least two production machines with NC control
(milling machines, lathe). These machines will be linked to a
transport system and they will be served by industrial robots. Within
this flexible manufacturing system a station for the quality control
consisting of a camera system and rack warehouse will be also
located. The design, analysis and improvement of this manufacturing
system, specially with a special focus on the communication among
devices constitute the main aims of this paper. The key determining
factors for the manufacturing system design are: the product, the
production volume, the used machines, the disposable manpower, the
disposable infrastructure and the legislative frame for the specific
cases.
Abstract: In this work a new platform for mobile-health systems is
presented. System target application is providing decision support to
rescue corps or military medical personnel in combat areas. Software
architecture relies on a distributed client-server system that manages a
wireless ad-hoc networks hierarchy in which several different types of
client operate. Each client is characterized for different hardware and
software requirements. Lower hierarchy levels rely in a network of
completely custom devices that store clinical information and patient
status and are designed to form an ad-hoc network operating in the
2.4 GHz ISM band and complying with the IEEE 802.15.4 standard
(ZigBee). Medical personnel may interact with such devices, that are
called MICs (Medical Information Carriers), by means of a PDA
(Personal Digital Assistant) or a MDA (Medical Digital Assistant),
and transmit the information stored in their local databases as well as
issue a service request to the upper hierarchy levels by using IEEE
802.11 a/b/g standard (WiFi). The server acts as a repository that
stores both medical evacuation forms and associated events (e.g., a
teleconsulting request). All the actors participating in the diagnostic
or evacuation process may access asynchronously to such repository
and update its content or generate new events. The designed system
pretends to optimise and improve information spreading and flow
among all the system components with the aim of improving both
diagnostic quality and evacuation process.
Abstract: The posteroanterior manipulation technique is usually include in the procedure of the lumbar spine to evaluate the intervertebral motion according to mechanical resistance. The mechanical device with visual feedback was proposed that allows one to analysis the lumbar segments mobility “in vivo" facilitating for the therapist to take its treatment evolution. The measuring system uses load cell and displacement sensor to estimate spine stiffness. In this work, the device was tested by 2 therapists, female, applying posteroanterior force techniques to 5 volunteers, female, with frequency of approximately 1.2-1.8 Hz. A test-retest procedure was used for 2 periods of day. The visual feedback results small variation of forces and cycle time during 6 cycles rhythmic application. The stiffness values showed good agreement between test-retest procedures when used same order of maximum forces.
Abstract: The need for micromechanical inertial sensors is increasing
in future electronic stability control (ESC) and other positioning,
navigation and guidance systems. Due to the rising density of
sensors in automotive and consumer devices the goal is not only to get
high performance, robustness and smaller package sizes, but also to
optimize the energy management of the overall sensor system. This
paper presents an evaluation concept for a surface micromachined
yaw rate sensor. Within this evaluation concept an energy-efficient
operation of the drive mode of the yaw rate sensor is enabled. The
presented system concept can be realized within a power management
subsystem.
Abstract: Existing methods in which the animation data of all frames are stored and reproduced as with vertex animation cannot be used in mobile device environments because these methods use large amounts of the memory. So 3D animation data reduction methods aimed at solving this problem have been extensively studied thus far and we propose a new method as follows. First, we find and remove frames in which motion changes are small out of all animation frames and store only the animation data of remaining frames (involving large motion changes). When playing the animation, the removed frame areas are reconstructed using the interpolation of the remaining frames. Our key contribution is to calculate the accelerations of the joints of individual frames and the standard deviations of the accelerations using the information of joint locations in the relevant 3D model in order to find and delete frames in which motion changes are small. Our methods can reduce data sizes by approximately 50% or more while providing quality which is not much lower compared to original animations. Therefore, our method is expected to be usefully used in mobile device environments or other environments in which memory sizes are limited.
Abstract: Magnetic and semiconductor nanomaterials exhibit
novel magnetic and optical properties owing to their unique size and
shape-dependent effects. With shrinking the size down to nanoscale
region, various anomalous properties that normally not present in bulk
start to dominate. Ability in harnessing of these anomalous properties
for the design of various advance electronic devices is strictly
dependent on synthetic strategies. Hence, current research has focused
on developing a rational synthetic control to produce high quality
nanocrystals by using organometallic approach to tune both size and
shape of the nanomaterials. In order to elucidate the growth
mechanism, transmission electron microscopy was employed as a
powerful tool in performing real time-resolved morphologies and
structural characterization of magnetic (Fe3O4) and semiconductor
(ZnO) nanocrystals. The current synthetic approach is found able to
produce nanostructures with well-defined shapes. We have found that
oleic acid is an effective capping ligand in preparing oxide-based
nanostructures without any agglomerations, even at high temperature.
The oleate-based precursors and capping ligands are fatty acid
compounds, which are respectively originated from natural palm oil
with low toxicity. In comparison with other synthetic approaches in
producing nanostructures, current synthetic method offers an effective
route to produce oxide-based nanomaterials with well-defined shapes
and good monodispersity. The nanocystals are well-separated with
each other without any stacking effect. In addition, the as-synthesized
nanopellets are stable in terms of chemically and physically if
compared to those nanomaterials that are previous reported. Further
development and extension of current synthetic strategy are being
pursued to combine both of these materials into nanocomposite form
that will be used as “smart magnetic nanophotocatalyst" for industry
waste water treatment.