Abstract: The construction of original functional sample of the portable device for fast analysis of energetic materials has been described in the paper. The portable device consisting of two parts – an original miniaturized microcolumn liquid chromatograph and a unique chemiluminescence detector – has been proposed and realized. In a very short time, this portable device is capable of identifying selectively most of military nitramine- and nitroesterbased explosives as well as inorganic nitrates occurring in trace concentrations in water or in soil. The total time required for the identification of extracts is shorter than 8 minutes.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: Atherosclerosis is the condition in which an artery
wall thickens as the result of a build-up of fatty materials such as
cholesterol. It is a syndrome affecting arterial blood vessels, a
chronic inflammatory response in the walls of arteries, in large part
due to the accumulation of macrophage white blood cells and
promoted by low density (especially small particle) lipoproteins
(plasma proteins that carry cholesterol and triglycerides) without
adequate removal of fats and cholesterol from the macrophages by
functional high density lipoproteins (HDL). It is commonly referred
to as a hardening or furring of the arteries. It is caused by the
formation of multiple plaques within the arteries.
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: Calcium magnesium acetate (CMA) is environmentally
benign deicing chemicals that can replace sodium chloride that is
widely used on roads and highways at present for snow and ice control
to provide safe driving conditions during winter. The price of CMA
from petroleum-derived acetic acid is quite expensive. The bamboo
vinegar is the by-product from bamboo charcoal production. The
bamboo vinegar was used to prepare calcium acetate as raw materials,
and its deicing and corrosive performances were studied in this paper.
The results show that the freezing temperature of calcium acetate is
lower than that of sodium chloride when they have same molar
concentration, the deicing performance of calcium acetate is better
than that of sodium chloride when they have same moles, while the
deicing performance of sodium chloride is better than that of calcium
acetate. The corrosion of sodium chloride on iron-nail and steel-nail is
larger than that of calcium acetate whether they have same mass
concentration or same molar concentration, and the corrosion of
sodium chloride and calcium acetate on iron-nail is larger than that on
steel-nail, and calcium acetate almost hasn't corrosion on steel-nail.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: Friction Stir Welding is a solid state welding technique which can be used to produce sound welds between similar and dissimilar materials. Dissimilar welds which include welds between the different series of aluminium alloys, aluminium to magnesium, steel and titanium has been successfully produced by many researchers. This review covers the work conducted in the above mentioned materials and further concludes by showing the need to fully understand the FSW process in order to expand the latter industrially.
Abstract: When considering the development of constitutive
equations describing the behavior of materials under cyclic plastic
strains, different kinds of formulations can be adopted. The primary
intention of this study is to develop computer programming of
plasticity models to accurately predict the life of engineering
components. For this purpose, the energy or cyclic strain is computed
in multi-surface plasticity models in non-proportional loading and to
present their procedures and codes results.
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: Within the last years, several technologies have been developed to help building e-learning portals. Most of them follow approaches that deliver a vast amount of functionalities, suitable for class-like learning. The SuGI project, as part of the D-Grid (funded by the BMBF), targets on delivering a highly scalable and sustainable learning solution to provide materials (e.g. learning modules, training systems, webcasts, tutorials, etc.) containing knowledge about Grid computing to the D-Grid community. In this article, the process of the development of an e-learning portal focused on the requirements of this special user group is described. Furthermore, it deals with the conceptual and technical design of an e-learning portal, addressing the special needs of heterogeneous target groups. The main focus lies on the quality management of the software development process, Web templates for uploading new contents, the rich search and filter functionalities which will be described from a conceptual as well as a technical point of view. Specifically, it points out best practices as well as concepts to provide a sustainable solution to a relatively unknown and highly heterogeneous community.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: Selective oxidation of H2S to elemental sulfur in a
fixed bed reactor over newly synthesized alumina nanocatalysts was
physio-chemically investigated and results compared with a
commercial Claus catalyst. Amongst these new materials, Al2O3-
supported sodium oxide prepared with wet chemical technique and
Al2O3 nanocatalyst prepared with spray pyrolysis method were the
most active catalysts for selective oxidation of H2S to elemental
sulfur. Other prepared nanocatalysts were quickly deactivated,
mainly due to the interaction with H2S and conversion into sulfides.
Abstract: Korea Train eXpress (KTX) is now being operated,
which allows Korea being one of the countries that operates the
high-speed rail system. The high-speed rail has its advantage of short
time transportation of population and materials, which lead to many
researches performed in this matter. In the case of high speed classical
trackbed system, the maintenance and usability of gravel ballast
system is costly. Recently, the concrete trackbed structure has been
introduced as a replacement of classical trackbed system. In this case,
the sleeper plays a critical role. Current study investigated to develop
the track sleepers readily applicable to the top of the asphalt trackbed,
as part of the trcakbed study utilizing the asphalt material. Among
many possible shapes and design of sleepers, current study proposed
two types of wide-sleepers according to the shear-key installation
method. The structural behavior analysis and safety evaluation on each
case was conducted using Korean design standard.
Abstract: Carbon steel is used in boilers, pressure vessels, heat
exchangers, piping, structural elements and other moderatetemperature
service systems in which good strength and ductility are
desired. ASME Boiler and Pressure Vessel Code, Section II Part A
(2004) provides specifications of ferrous materials for construction of
pressure equipment, covering wide range of mechanical properties
including high strength materials for power plants application.
However, increased level of springback is one of the major problems
in fabricating components of high strength steel using bending.
Presented work discuss the springback simulations for five different
steels (i.e. SA-36, SA-299, SA-515 grade 70, SA-612 and SA-724
grade B) using finite element analysis of air V-bending. Analytical
springback simulations of hypothetical layered materials are
presented. Result shows that; (i) combination of the material property
parameters controls the springback, (ii) layer of the high ductility
steel on the high strength steel greatly suppresses the springback.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: Due to its geographical location, Iran is considered one of the earthquake-prone areas where the best way to decrease earthquake effects is supposed to be strengthening the buildings. Even though, one idea suggests that the use of adobe in constructing buildings be prohibited for its weak function especially in earthquake-prone areas, however, regarding ecological considerations, sustainability and other local skills, another idea pays special attention to adobe as one of the construction technologies which is popular among people. From the architectural and technological point of view, as strong sustainable building construction materials, compressed adobe construction materials make most of the construction in urban or rural areas ranging from small to big industrial buildings used to replace common earth blocks in traditional systems and strengthen traditional adobe buildings especially against earthquake. Mentioning efficient construction using compressed adobe system as a reliable replacement for traditional soil construction materials , this article focuses on the experiences of India in the fields of sustainable development of compressed adobe systems in the form of system in which the compressed soil is combined with cement, load bearing building with brick/solid concrete block system, brick system using rat trap bond, metal system with adobe infill and finally emphasizes on the use of these systems in the earthquake-struck city of Bam in Iran.
Abstract: Three dimensional nanostructure materials have attracted the attention of many researches because the possibility to apply them for near future devices in sensors, catalysis and energy related. Tin dioxide is the most used material for gas sensing because its three-dimensional nanostructures and properties are related to the large surface exposed to gas adsorption. We propose the use of branch SnO2 nanowhiskers in interaction with ethanol. All Sn atoms are symmetric. The total energy, potential energy and Kinetic energy calculated for interaction between SnO2 and ethanol in different distances and temperatures. The calculations achieved by methods of Langevin Dynamic and Mont Carlo simulation. The total energy increased with addition ethanol molecules and temperature so interactions between them are endothermic.
Abstract: Chloride induced corrosion of steel reinforcement is
the main cause of deterioration of reinforced concrete marine
structures. This paper investigates the relative performance of
alternative repair options with respect to the deterioration of
reinforced concrete bridge elements in marine environments. Focus is
placed on the initiation phase of reinforcement corrosion. A
laboratory study is described which involved exposing concrete
samples to accelerated chloride-ion ingress. The study examined the
relative efficiencies of two repair methods, namely Ordinary Portland
Cement (OPC) concrete and a concrete which utilised Ground
Granulated Blastfurnace Cement (GGBS) as a partial cement
replacement. The mix designs and materials utilised were identical to
those implemented in the repair of a marine bridge on the South East
coast of Ireland in 2007. The results of this testing regime serve to
inform input variables employed in probabilistic modelling of
deterioration for subsequent reliability based analysis to compare the
relative performance of the studied repair options.