Abstract: The purpose of this research was to analyze and compare the instability of a contact surface between Copper and Nickel an alloy cathode in vacuum, the different ratio of Copper and Copper were conducted at 1%, 2% and 4% by using the cathode spot model. The transient recovery voltage is predicted. The cathode spot region is recognized as the collisionless space charge sheath connected with singly ionized collisional plasma. It was found that the transient voltage is decreased with increasing the percentage of an amount of Nickel in cathode materials.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: The 'wind-rain' house has a courtyard with glazed
roof, which allows more direct sunlight to come into indoor spaces
during the winter. The glazed roof can be partially opened or closed
and automatically controlled to provide natural ventilation in order to
adjust for indoor thermal conditions and the roof area can be shaded
by reflective insulation materials during the summer. Two field
studies for evaluating indoor thermal conditions of the two 'windrain'
houses have been carried out by author in 2009 and 2010.
Indoor and outdoor air temperature and relative humidity adjacent to
floor and ceiling of the two sample houses were continuously tested
at 15-minute intervals, 24 hours a day during the winter months.
Based on field study data, this study investigates relationships
between building design and indoor thermal condition of the 'windrain'
house to improve the future house design for building thermal
comfort and energy efficiency
Abstract: Optical Coherence Tomography (OCT) combined
with the Confocal Microscopy, as a noninvasive method, permits the
determinations of materials defects in the ceramic layers depth. For
this study 256 anterior and posterior metal and integral ceramic fixed
partial dentures were used, made with Empress (Ivoclar), Wollceram
and CAD/CAM (Wieland) technology. For each investigate area 350
slices were obtain and a 3D reconstruction was perform from each
stuck. The Optical Coherent Tomography, as a noninvasive method,
can be used as a control technique in integral ceramic technology,
before placing those fixed partial dentures in the oral cavity. The
purpose of this study is to evaluate the capability of En face Optical
Coherence Tomography (OCT) combined with a fluorescent method
in detection and analysis of possible material defects in metalceramic
and integral ceramic fixed partial dentures. As a conclusion,
it is important to have a non invasive method to investigate fixed
partial prostheses before their insertion in the oral cavity in order to
satisfy the high stress requirements and the esthetic function.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: The balance between nitrogen loading and runoff in the
forested headwater streams of the Kanna River was estimated to
elucidate the current status of nitrogen saturation in a forested
watershed. NO3-N concentration in the study area was far higher than
the average value in Japan. Estimated nitrogen runoff accounted for
55–57% of nitrogen loading; suggesting that the forest-s nitrogen
retention capacity is most likely in decline. Since the 1970s, Japan-s
forestry industry has been declining due to the decrease in lumber
demand and increase in cheap imported materials. Thus, this decline
will contribute significantly to further reducing nitrogen saturation in
forest ecosystems.
Abstract: This paper presents an assessment study conducted
among the distance learners in India. Open and distance learning
systems have traveled a long way since its inception and its journey
has witnessed the evolution and adoption of different generations of
technology. This study focuses on the distant learners in India.
Sampling for this study has been derived from the mass enrollment
from Tamil Nadu area, a southern state of India. Learners were
chosen from dual mode universities, private universities, Tamil Nadu
Open University and IGNOU. The main focus of the study is to
examine the coverage and appropriation of students support services
and learning aids. It explores two aspects: the facilities available and
the awareness and use of such services. It includes, self-learning
materials, face-to-face counseling, multimedia learning materials,
website, e-learning, radio and television services etc. While exploring
the student-s perspective on these learning aspects, it is important to
understand the perspectives of the teachers. Two different interests
are visible among the teachers. Majority of the teachers support faceto-
face counseling. However, the young teachers are in favour of
online learning and multimedia supports in teaching. Through the
awareness is somewhat high, the actual participation in online is very
low. This is due to the inadequate infrastructure as well as the
traditional attitudes of the teachers. Still the face-to-face sessions
remain popular than online.
Abstract: Calculations of energy efficiency of several AACbased
building envelopes under different climatic conditions are
presented. As thermal insulating materials, expanded polystyrene and
hydrophobic and hydrophilic mineral wools are assumed. The
computations are accomplished using computer code HEMOT
developed at Department of Materials Engineering, Faculty of Civil
Engineering at the Czech Technical University in Prague. The
climatic data of Athens, Kazan, Oslo, Prague and Reykjavík are
obtained using METEONORM software.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: The objective of this study is to investigate the effect of adding coal to obtain insulating ceramic product. The preparation of mixtures is achieved with 04 types of different masse compositions, consisting of gray and yellow clay, and coal. Analyses are performed on local raw materials by adding coal as additive. The coal content varies from 5 to 20 % in weight by varying the size of coal particles ranging from 0.25mm to 1.60mm.
Initially, each natural moisture content of a raw material has been determined at the temperature of 105°C in a laboratory oven. The Influence of low-coal content on absorption, the apparent density, the contraction and the resistance during compression have been evaluated. The experimental results showed that the optimized composition could be obtained by adding 10% by weight of coal leading thus to insulating ceramic products with water absorption, a density and resistance to compression of 9.40 %, 1.88 g/cm3, 35.46 MPa, respectively. The results show that coal, when mixed with traditional raw materials, offers the conditions to be used as an additive in the production of lightweight ceramic products.
Abstract: A collaboration among the Hospital S. Giovanni Battista
of Turin, the Politecnico of Turin, and the MUST company is
described. The content of the collaboration has been and is the use of
ICT-s, e-learning, and blended learning for the internal professional
education, training, and keeping up to date of the personnel of the
hospital. A platform for the delivery of the teaching materials has
been built, including an evaluation and self-evaluation tool. The first
on line courses have been developed and delivered and many more
are in preparation. The first results of the monitoring of the efficacy
of the online education have been positive.
Abstract: Nowadays e-Learning is more popular, in Vietnam
especially. In e-learning, materials for studying are very important.
It is necessary to design the knowledge base systems and expert
systems which support for searching, querying, solving of
problems. The ontology, which was called Computational Object
Knowledge Base Ontology (COB-ONT), is a useful tool for
designing knowledge base systems in practice. In this paper, a
design method for knowledge base systems in education using
COKB-ONT will be presented. We also present the design of a
knowledge base system that supports studying knowledge and
solving problems in higher mathematics.
Abstract: This study evaluated the microbiological quality
and the sensory characteristics of carp fillets processed by the
sousvide method when stored at 2 and 10 °C. Four different
combinations of sauced–storage were studied then stored at 2 or 10
°C was evaluate periodically sensory, microbiological and
chemical quality. Batches stored at 2 °C had lower growth rates of
mesophiles and psychrotrophs. Moreover, these counts decreased
by increasing the heating temperature and time. Staphylococcus
aureus, Bacillus cereus, Clostridium perfringens and Listeria
monocytogenes were not found in any of the samples. The heat
treatment of 90 °C for 15 min and sauced was the most effective to
ensure the safety and extend the shelf-life of sousvide carp
preserving its sensory characteristics. This study establishes the
microbiological quality of sous vide carp and emphasizes the
relevance of the raw materials, heat treatment and storage
temperature to ensure the safety of the product.
Abstract: The ability to predict an accurate temperature
distribution requires the knowledge of the losses, the thermal
characteristics of the materials, and the cooling conditions, all of
which are very difficult to quantify. In this paper, the impact of the
effects of iron and copper losses are investigated separately and
their effects on the heating in various points of the stator of an
induction motor, is highlighted by using two simple tests. In addition,
the effect of a defect, such as an open circuit in a phase of the stator,
on the heating is also obtained by a no-load test.
The squirrel cage induction motor is rated at 2.2 kW; 380 V; 5.2
A; Δ connected; 50 Hz; 1420 rpm and the class of insulation F, has
been thermally tested under several load conditions. Several
thermocouples were placed in strategic points of the stator.
Abstract: There is inadequate information on the practice of
female genital mutilation (FGM) in the UK, and there are often
myths and perceptions within communities that influence the
effectiveness of prevention programmes. This means it is difficult to
address the trends and changes in the practice in the UK.
To this end, FORWARD undertook novel and innovative research
using the Participatory Ethnographic and Evaluative Research
(PEER) method to explore the views of women from Eritrea, Sudan,
Somalia and Ethiopia that live in London and Bristol (two UK cities).
Women-s views, taken from PEER interviews, reflected reasons for
continued practice of FGM: marriageability, the harnessing and
control of female sexuality, and upholding traditions from their
countries of origin. It was also clear that the main supporters of the
practice were believed to be older women within families and
communities.
Women described the impact FGM was having on their lives as
isolating. And although it was clearly considered a private and
personal matter, they developed a real sense of connection with their
peers within the research process.
The women were overwhelmingly positive about combating the
practice, although they believed it would probably take a while
before it ends completely. They also made concrete
recommendations on how to improve support services for women
affected by FGM: Training for professionals (particularly in
healthcare), increased engagement with, and outreach to,
communities, culturally appropriate materials and information made
available and accessible to communities, and more consequent
implementation of legislation.
Finally, the women asked for more empathy and understanding,
particularly from health professionals. Rather than presenting FGM
as a completely alien and inconceivable practice, it may help for
those looking into these women-s lives and working with them to
understand the social and economic context in which the practice
takes place.
Abstract: An electrical apparatus for measuring moisture
content was developed by our laboratory and uses dependence of
electrical properties on water content in studied material. Error
analysis of the apparatus was run by measuring different volumes of
water in a simplified specimen, i.e. hollow plexiglass block, in order
to avoid as many side-effects as possible. Obtained data were
processed using both basic and advanced statistics and results were
compared with each other. The influence of water content on
accuracy of measured data was studied as well as the influence of
variation of apparatus' proper arrangement or factual methodics of its
usage. The overall coefficient of variation was 4%. There was no
trend found in results of error dependence on water content.
Comparison with current surveys led to a conclusion, that the studied
apparatus can be used for indirect measurement of water content in
porous materials, with expectable error and under known conditions.
Factual experiments with porous materials are not involved, but are
currently under investigation.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: The main purpose of this research was to study how to
communicate the identity of the Amphawa district, Samut Songkram
province for sustainable tourism. The qualitative data was collected
through studying related materials, exploring the area, in-depth
interviews with three groups of people: three directly responsible
officers who were key informants of the district, twenty foreign
tourists and five Thai tourist guides. A content analysis was used to
analyze the qualitative data. The two main findings of the study were
as follows:
1. The identity of the Amphawa District, Samut Songkram
province is the area controlled by Amphawa sub district (submunicipality).
The working unit which runs and looks after
Amphawa sub district administration is known as the Amphawa
mayor. This establishment was built to be a resort for normal
people and tourists visiting the Amphawa district near the
Maekong River consisting of rest accommodations. Along the
river there is a restaurant where food and drinks are served, rich
mangrove forests, a learning center, fireflies and cork trees. The
Amphawa district was built to honor and commemorate King
Rama II and is where the greatest number of fireflies and cork
trees can be seen in Thailand from May to October each year.
2. The communication of the identity of Amphawa District, Samut
Songkram Province which the researcher could find and design
to present in English materials can be summed up in 5 items: 1)
The history of the Amphawa District, Samut Songkram province
2) The history of King Rama II Memorial Park 3) The identity of
Amphawa Floating Market 4) The Learning center of
Ecosystem: Fireflies and Cork Trees 5) How to keep Amphawa
District, Samut Songkram Province for sustainable tourism.
Abstract: Nowadays due to globalization of economy and
competition environment, innovation and technology plays key role
at creation of wealth and economic growth of countries. In fact
prompt growth of practical and technologic knowledge may results in
social benefits for countries when changes into effective innovation.
Considering the importance of innovation for the development of
countries, this study addresses the radical technological innovation
introduced by nanopapers at different stages of producing paper
including stock preparation, using authorized additives, fillers and
pigments, using retention, calender, stages of producing conductive
paper, porous nanopaper and Layer by layer self-assembly. Research
results show that in coming years the jungle related products will lose
considerable portion of their market share, unless embracing radical
innovation. Although incremental innovations can make this industry
still competitive in mid-term, but to have economic growth and
competitive advantage in long term, radical innovations are
necessary. Radical innovations can lead to new products and
materials which their applications in packaging industry can produce
value added. However application of nanotechnology in this industry
can be costly, it can be done in cooperation with other industries to
make the maximum use of nanotechnology possible. Therefore this
technology can be used in all the production process resulting in the
mass production of simple and flexible papers with low cost and
special properties such as facility at shape, form, easy transportation,
light weight, recovery and recycle marketing abilities, and sealing.
Improving the resistance of the packaging materials without reducing
the performance of packaging materials enhances the quality and the
value added of packaging. Improving the cellulose at nano scale can
have considerable electron optical and magnetic effects leading to
improvement in packaging and value added. Comparing to the
specifications of thermoplastic products and ordinary papers,
nanopapers show much better performance in terms of effective
mechanical indexes such as the modulus of elasticity, tensile strength,
and strain-stress. In densities lower than 640 kgm -3, due to the
network structure of nanofibers and the balanced and randomized
distribution of NFC in flat space, these specifications will even
improve more. For nanopapers, strains are 1,4Gpa, 84Mpa and 17%,
13,3 Gpa, 214Mpa and 10% respectively. In layer by layer self
assembly method (LbL) the tensile strength of nanopaper with Tio3
particles and Sio2 and halloysite clay nanotube are 30,4 ±7.6Nm/g
and 13,6 ±0.8Nm/g and 14±0.3,3Nm/g respectively that fall within
acceptable range of similar samples with virgin fiber. The usage of
improved brightness and porosity index in nanopapers can create
more competitive advantages at packaging industry.