Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: This research was to evaluate a technical feasibility of
making single-layer experimental particleboard panels from bamboo
waste (Dendrocalamus asper Backer) by converting bamboo into
strips, which are used to make laminated bamboo furniture. Variable
factors were density (600, 700 and 800 kg/m3) and temperature of
condition (25, 40 and 55 °C). The experimental panels were tested for
their physical and mechanical properties including modulus of
elasticity (MOE), modulus of rupture (MOR), internal bonding
strength (IB), screw holding strength (SH) and thickness swelling
values according to the procedures defined by Japanese Industrial
Standard (JIS). The test result of mechanical properties showed that
the MOR, MOE and IB values were not in the set criteria, except the
MOR values at the density of 700 kg/m3 at 25 °C and at the density
of 800 kg/m3 at 25 and 40 °C, the IB values at the density of 600
kg/m3, at 40 °C, and at the density of 800 kg/m3 at 55 °C. The SH
values had the test result according to the set standard, except with
the density of 600 kg/m3, at 40 and 55 °C. Conclusively, a valuable
renewable biomass, bamboo waste could be used to manufacture
boards.
Abstract: The method of modeling is the key technology for
digital mockup (DMU). Based upon the developing for mechanical
product DMU, the theory, method and approach for virtual
environment (VE) and virtual object (VO) were studied. This paper
has expounded the design goal and architecture of DMU system,
analyzed the method of DMU application, and researched the general
process of physics modeling and behavior modeling.
Abstract: This article is devoted to the numerical solution of
large-scale quadratic eigenvalue problems. Such problems arise in
a wide variety of applications, such as the dynamic analysis of
structural mechanical systems, acoustic systems, fluid mechanics,
and signal processing. We first introduce a generalized second-order
Krylov subspace based on a pair of square matrices and two initial
vectors and present a generalized second-order Arnoldi process for
constructing an orthonormal basis of the generalized second-order
Krylov subspace. Then, by using the projection technique and the
refined projection technique, we propose a restarted generalized
second-order Arnoldi method and a restarted refined generalized
second-order Arnoldi method for computing some eigenpairs of largescale
quadratic eigenvalue problems. Some theoretical results are also
presented. Some numerical examples are presented to illustrate the
effectiveness of the proposed methods.
Abstract: The plastic flow of metal in the extrusion process is
an important factor in controlling the mechanical properties of the
extruded products. It is, however, difficult to predict the metal flow
in three dimensional extrusions of sections due to the involvement of
re-entrant corners. The present study is to find an upper bound
solution for the extrusion of triangular sectioned through taper dies
from round sectioned billet. A discontinuous kinematically
admissible velocity field (KAVF) is proposed. From the proposed
KAVF, the upper bound solution on non-dimensional extrusion
pressure is determined with respect to the chosen process parameters.
The theoretical results are compared with experimental results to
check the validity of the proposed velocity field. An extrusion setup
is designed and fabricated for the said purpose, and all extrusions are
carried out using circular billets. Experiments are carried out with
commercially available lead at room temperature.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: Most file systems overwrite modified file data and
metadata in their original locations, while the Log-structured File
System (LFS) dynamically relocates them to other locations. We
design and implement the Evergreen file system that can select
between overwriting or relocation for each block of a file or metadata.
Therefore, the Evergreen file system can achieve superior write
performance by sequentializing write requests (similar to LFS-style
relocation) when space utilization is low and overwriting when
utilization is high. Another challenging issue is identifying
performance benefits of LFS-style relocation over overwriting on a
newly introduced SSD (Solid State Drive) which has only
Flash-memory chips and control circuits without mechanical parts.
Our experimental results measured on a SSD show that relocation
outperforms overwriting when space utilization is below 80% and vice
versa.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.
Abstract: A biophysically based multilayer continuum model of the facial soft tissue composite has been developed for simulating wrinkle formation. The deformed state of the soft tissue block was determined by solving large deformation mechanics equations using the Galerkin finite element method. The proposed soft tissue model is composed of four layers with distinct mechanical properties. These include stratum corneum, epidermal-dermal layer (living epidermis and dermis), subcutaneous tissue and the underlying muscle. All the layers were treated as non-linear, isotropic Mooney Rivlin materials. Contraction of muscle fibres was approximated using a steady-state relationship between the fibre extension ratio, intracellular calcium concentration and active stress in the fibre direction. Several variations of the model parameters (stiffness and thickness of epidermal-dermal layer, thickness of subcutaneous tissue layer) have been considered.
Abstract: During the last decade ultrafine grained (UFG) and nano-structured (NS) materials have experienced a rapid development. In this research work finite element analysis has been carried out to investigate the plastic strain distribution in equal channel angular process (ECAP). The magnitudes of Standard deviation (S. D.) and inhomogeneity index (Ci) were compared for different ECAP passes. Verification of a three-dimensional finite element model was performed with experimental tests. Finally the mechanical property including impact energy of ultrafine grained pure commercially pure Aluminum produced by severe plastic deformation method has been examined. For this aim, equal channel angular pressing die with the channel angle, outer corner angle and channel diameter of 90°, 20° and 20mm had been designed and manufactured. Commercial pure Aluminum billets were ECAPed up to four passes by route BC at the ambient temperature. The results indicated that there is a great improvement at the hardness measurement, yield strength and ultimate tensile strength after ECAP process. It is found that the magnitudes of HV reach 67HV from 21HV after the final stage of process. Also, about 330% and 285% enhancement at the YS and UTS values have been obtained after the fourth pass as compared to the as-received conditions, respectively. On the other hand, the elongation to failure and impact energy have been reduced by 23% and 50% after imposing four passes of ECAP process, respectively.
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: Low frequency power oscillations may be triggered
by many events in the system. Most oscillations are damped by the
system, but undamped oscillations can lead to system collapse.
Oscillations develop as a result of rotor acceleration/deceleration
following a change in active power transfer from a generator. Like
the operations limits, the monitoring of power system oscillating
modes is a relevant aspect of power system operation and control.
Unprevented low-frequency power swings can be cause of cascading
outages that can rapidly extend effect on wide region. On this regard,
a Wide Area Monitoring, Protection and Control Systems
(WAMPCS) help in detecting such phenomena and assess power
system dynamics security. The monitoring of power system
electromechanical oscillations is very important in the frame of
modern power system management and control. In first part, this
paper compares the different technique for identification of power
system oscillations. Second part analyzes possible identification
some power system dynamics behaviors Using Wide Area
Monitoring Systems (WAMS) based on Phasor Measurement Units
(PMUs) and wavelet technique.
Abstract: A multi fingered dexterous anthropomorphic hand is
being developed by the authors. The focus of the hand is the
replacement of human operators in hazardous environments and also
in environments where zero tolerance is observed for the human
errors. The robotic hand will comprise of five fingers (four fingers
and one thumb) each having four degrees of freedom (DOF) which
can perform flexion, extension, abduction, adduction and also
circumduction. For the actuation purpose pneumatic muscles and
springs will be used. The paper exemplifies the mechanical design for
the robotic hand. It also describes different mechanical designs that
have been developed before date.
Abstract: The thermal expansion behaviour of silicon carbide
(SCS-2) fibre reinforced 6061 aluminium matrix composite subjected
to the influenced thermal mechanical cycling (TMC) process were
investigated. The thermal stress has important effect on the
longitudinal thermal expansion coefficient of the composites. The
present paper used experimental data of the thermal expansion
behaviour of a SiC/Al composite for temperatures up to 370°C, in
which their data was used for carrying out modelling of theoretical
predictions.
Abstract: The development of the power electronics has allowed
increasing the precision and reliability of the electrical devices, thanks
to the adjustable inverters, as the Pulse Wide Modulation (PWM)
applied to the three level inverters, which is the object of this study.
The authors treat the relation between the law order adopted for a
given system and the oscillations of the electrical and mechanical
parameters of which the tolerance depends on the process with which
they are integrated (paper factory, lifting of the heavy loads,
etc.).Thus, the best choice of the regulation indexes allows us to
achieve stability and safety training without investment (management
of existing equipment). The optimal behavior of any electric device
can be achieved by the minimization of the stored electrical and
mechanical energy.
Abstract: Hardness of the widely used structural steel is of vital
importance since it may help in the determination of many
mechanical properties of a material under loading situations. In order
to obtain reliable information for design, properties homogeneity
should be validated. In the current study the hardness variation over
the different diameters of the same AISI 4140 bar is investigated.
Measurements were taken on the two faces of the stock at equally
spaced eight sectors and fifteen layers. Statistical and graphical
analysis are performed to asses the distribution of hardness
measurements over the specified area. Hardness measurements
showed some degree of dispersion with about ± 10% of its nominal
value provided by manufacturer. Hardness value is found to have a
slight decrease trend as the diameter is reduced. However, an
opposite behavior is noticed regarding the sequence of the sector
indicating a nonuniform distribution over the same area either on the
same face or considering the corresponding sector on the other face
(cross section) of the same material bar.
Abstract: Computer aided design accounts with the support of
parametric software in the design of machine components as well as
of any other pieces of interest. The complexities of the element under
study sometimes offer certain difficulties to computer design, or ever
might generate mistakes in the final body conception. Reverse
engineering techniques are based on the transformation of already
conceived body images into a matrix of points which can be
visualized by the design software. The literature exhibits several
techniques to obtain machine components dimensional fields, as
contact instrument (MMC), calipers and optical methods as laser
scanner, holograms as well as moiré methods. The objective of this
research work was to analyze the moiré technique as instrument of
reverse engineering, applied to bodies of nom complex geometry as
simple solid figures, creating matrices of points. These matrices were
forwarded to a parametric software named SolidWorks to generate
the virtual object. Volume data obtained by mechanical means, i.e.,
by caliper, the volume obtained through the moiré method and the
volume generated by the SolidWorks software were compared and
found to be in close agreement. This research work suggests the
application of phase shifting moiré methods as instrument of reverse
engineering, serving also to support farm machinery element designs.